Forest garden OASBFP User manual

Pre-drill
for each screw
used.
This article contains biocidal products to give protection against
wood destroying insects & wood rotting fungi. Contents may vary.
May contain : Basic copper carbonate (Copper (II) carbonate –
Copper (II) hydroxide (1:1), Cupric oxide, Copper hydroxide
carbonate, oxyethyl, ammoniumpropionate, Copper HDO,
Propiconazole, Tebuconazole, Boric acid, Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing
dust when cutting treated or untreated wood. Dispose of off-cuts
responsibly – do not burn.
Drill/Pozi Drive
Screwdriver
Tape Measure
Tools Required
Not Supplied
Spirit Level
Hammer
Sharp Knife
Fixing Pack Code = OASBFP
a
c
aad
ae
f
50mm Screw Qty 12 25mm Screw Qty 59
30mm Nail Qty 32
Hasp And Staple Qty 1
Flush Hinge Qty 2
b
Felt Tacks Qty 30
Shiplap Small Garden Store
OASBFP
Please make sure you quote from the parts list in the event you need to order replacemements.
Important:
Assembly of this product requires a minimum of two
adults.
Attention:
nFor Domestic Use Only.
nMust be built on a and base.solid level
nRegularly check that all fixing are tight and secure.
nRegularly check the felt for damage.
Forest Garden Ltd. | Unit 288 | Oak Drive | Hartlebury Trading Estate | Hartlebury| Worcestershire | DY10 4JB Issue 0218
This product is pressure to ensure longevity of all timber componentstreated
and to protect against rot. This may leave a colour difference on some parts
that will even out as the moisture content stabilises This will not need.
additional treatment.
nPlease keep all plastic bags and small parts away from children.
nThe roof of this product is not a load bearing structure.
nTimber is a natural material and will shrink and swell as a result of
varying moisture content.
Assembly of damaged parts may be deemed to be acceptance and this may
affect the remedies you are entitled to.
If the product is not constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot be held liable for
any resulting damage.
Please check all parts prior to assembly.
Item Document Number Title Quantity
1 HSBFRP PTR HALF SENTRY BOX FRONT PANEL 1
2 SPMSSP SLAP PTR MIDI STORE SIDE PANEL 3
3 PHSBDR PTR HALF SENTRY BOX DOOR 1
4 44121255PPT STRIP 44x12x1255mm PAR PTREAT 4
5 121120392AII70PT BOARD 121x12x392mm ANGLED PTREAT 4
6 4823358 OSB 482x335x8mm 2
7 28280482 BATTEN 28x28x482mm 2
8 45280150PT BATTEN 45x28x150mm PTREAT 4
9 121120282PAII70PT BOARD 121x12x282mm PAR ANGLED PTREAT 4
10 5034478 OSB 503x447x8mm 1
11 28280503PT BATTEN 28x28x503mm PTREAT 2
12 28280070PT BATTEN 28x28x70mm PTREAT 4
13 121120481PPT BOARD 121x12x481mm PAR PTREAT 2
14 85068 GREEN FELT 1.3x1 METRE 1
Help line: 08:30 to 17:00 Monday to Friday0333 7777 089
SPASGS PARTS LISTSPASGS PARTS LIST

AB
CD
PRE-DRILL PRE-DRILL PRE-DRILL
ae
1
2Place the panels on top of the base
making sure that they are all tight
and flush before fixing the panels
together using 2x 50mm screws for
each corner.
Fix the front and back panels to
the floor using 2 x 50mm screws
for each screwing down through
the framing from inside.
f
f
f
f
f
f
f
f
11
10
9
Place the angled boards against the
front and back panels as shown to
create an apex. Fix each board in
place using 2 x 25mm screws.
Fix each of the corner strips along the
edges so that they are flush and fix
each in place using 3 x nails.
f
f
f
Floor Assembly
Board and batten
should be flush.
e
4
e
ee
d
d
85mm
The top point of the
board should be offset
85mm from the panel

EF
GH
ab
Take care when
trimming the roof
felt.
14
ab
ab
d
x 6
The top of the hinge
should be in line with
the horizontal batten
Fix the smaller
piece of the hinge
to the door.
ac
6
8
8
7
f
f
f
f
f
f
ff
ff
d
Fix the roof board to the battens as
shown using nails.
Repeat for the other roof section.
Slot the roof sections so that they line up at the apex. Fix these from the inside screwing through
the apex boards into the 150mm battens using 25mm screws for each.
Place the felt over the roof so that
there is approximately a 45mm
overhang on all sides. Secure the felt to
the roof, nailing into the ba! ens from
the sides using felt tacks placed at
150mm intervals.
Cut and fold the felt at the corners as
shown.
PRE-DRILL PRE-DRILL PRE-DRILL
45mm
3

IJ
K
13
12
5
d
d
d
d
d
d
d
d
d
d
Position and line up the hasp
and staple with framing on the
inside of the door.
a
d
x 7
Fix the 481mm board to two of the 70mm battens.
These should be flush on the short side and off set
10mm from the long side. Fix the battens in place
using 2 x 25mm screws for each.
Repeat with the remaining blocks and 481mm board.
Forest Garden Ltd. | Unit 288 | Oak Drive | Hartlebury Trading Estate | Hartlebury | Worcestershire | DY10 4JB Issue 0218
Make sure that the screws are
positioned so that each locates
into the batten.
PRE-DRILL PRE-DRILL PRE-DRILL
138cm
50cm
65cm
48cm