Four E's Scientific KING KONG MI0102001D User manual

Operating Instructions
Mini Magnetic Stirrer
KING KONG
MI0102001D

Contents
Safety Instructions
Unpacking
Correct Use
Operator’s Control
Installation
Maintenance
Accessories
Warranty
Technical Data
2
4
5
5
5
6
6
7
8
1

Safety Instructions
For your protection
• Read the operating instructions in full before
starting up and follow the safety instructions.
• Keep the operating instructions in a place where they
can be accessed by everyone.
• Ensure that only trained staff work with the appliance.
• Follow the safety instructions, guidelines, occupational
health and safety and accident prevention regulations.
• Caution-Magnetism! Effects of the magnetic field have
to be taken in to account (e.g. data storage media,
cardiac pacemakers…).
• Wear your personal protective equipment in accordance
with the hazard category of the media to be processed.
Otherwise there is a risk from:
- Splashing and evaporation of liquids
- Ejection of parts
- Release of toxic or combustible gases
• Use only the AC adapter supplied
• Set up the appliance in a spacious area on an even,
stable, clean, non-slip, dry and fireproof surface.
• The base plate must be clean and intact.
• Check the appliance and accessories before hand for
damage each time you use them. Do not use damaged
components.
• Reduce the speed if
- The medium splashes out of the vessel because the
speed is too high
2

- The appliance is not running smoothly
- The container moves on the base plate
• Beware of hazards due to:
- Flammable materials
- Combustible media with a low boiling temperature
- Incorrect container size
- Overfilling of media
- Unsafe condition of container.
• The appliance may heat up when in use.
• Process pathogenic materials only in closed vessels
under a suitable extractor hood. Please contact 4E’s if
you have questions.
• Do not operate the appliance in explosive atmospheres,
with hazardous substances or under water.
• Only process media that will not react dangerously to
the extra energy produced through processing. This also
applies to any extra energy produced in other ways, e.g.
through light irradiation.
• Safe operation is only guaranteed with the accessories
described in the “Accessories” chapter.
• The centre of gravity of the assembly must lie within the
surface on which it is set up.
• The appliance must only be disconnected from the mains
supply by pulling out the plug-in power supply unit.
• Abrasion of the dispersion equipment or the rotating
accessories can get into the medium you are working on.
• When using the PTFE-coated magnetic bars, the
following has to be noted: chemical reactions of PTFE
occur in contact with molten or dissolved alkaline and
alkaline-earth metals, as well as with fine particle
powders of metals of the 2. and 3. group of the
3

periodical system at temperatures above 300-400°C .
Only elementary fluorine, chlorine trifluoride and alkaline
metals do attack PTFE, halogen hydrocarbons have a
reversible swelling effect.
To the protection of the equipment
Caution: Equipment may not be poured over with
aggressive media! Equipment never under water set!
• The voltage stated on the nameplate must correspond
to the mains voltage.
• Do not cover the device, even partially e.g. with metallic
plates or film. This results in overheating.
• Protect the appliance and accessories from bumps and
impacts.
• Ensure that the base plate is kept clean.
Unpacking
• Unpacking
- Please unpack the device carefully
- In the case of any damage a fact report must be set
immediately (post, rail or forwarder)
• Delivery scope
- Magnetic stirrer
- Plug-in power supply
- Operating instruction
Correct Use
• Use
- For mixing liquids
• Range of use
- Laboratories - Schools - Pharmacies
4

Speed
Time
Stop
Run
(When the cursor is switched to be at the time setting
area, press for 3 times)
Continuous
running
5
Operator’s Control
KEY
KEY KEY KEY
OLED
: Run/Stop
: 1) It works as the shift key to change the position of
the cursor before the unit is running
2) It works as the shift key to switch between the
Non-reverse mode and Reverse mode when the
unit is running.
: “+” Increase
: “-” Reduce
OLED Display
: Reverse mode
(The stirring direction will be inverted by 50 seconds)
: Non-reverse mode (Single-direction rotation)

Installation
• Connect the appliance to a socket (the voltages stated on
the nameplates must correspond to the mains voltage).
• OLED is light and records the speed and time data of
last running
• Set the timing operation and continuous operation
before running. (Switch the cursor to the time setting
area by and set the value by and )
• Place a stirring bar in a vessel which is penetrable for
magnetic field lines and fill the vessel with the medium
to be processed.
• Place the vessel on the centre of the set-up surface.
• Start the unit by “Run/stop”
• Set the reverse mode only when the unit is running
Maintenance
The appliance is maintenance-free.
Cleaning
Only use cleansing agents which have been
recommended by us
Use to remove
6
Dyes
Constructions materials
Cosmetics
Foodstuffs
Fuels
isopropyl alcohol
water containing tenside /
isopropyl alcohol
water containing tenside /
isopropyl alcohol
water containing tenside
water containing tenside

7
• Do not allow moisture to get into the appliance when
cleaning.
• Wear protective gloves during cleaning the devices
Before using another than recommended method for
cleaning or decontamination, the user must ascertain
with us that this method does not destroy the
instrument.
Accessories
25mm*7mm Stirring bar
12V 1A Power adapter
Operating Instruction
Warranty
In accordance with our warranty conditions, the warranty
period is 24 months. For claims under the warranty please
contact your local dealer. You may also send the machine
directly to our factory, enclosing the delivery invoice and
giving reasons for the claim. You will be liable for freight
costs.
The warranty covers the centrifuge and rotor. It is void in
the event of incorrect operation, use of nonstandard spare
parts or accessories and unauthorized modification of the
rotor or centrifuge. The rotor warranty does not cover
normal wear and tear or damage and/or weakening
caused by radioactive contamination, cleaning agents, or
over tightening of the allen screw.

8
Model
Stirring Positions
Working plate material
Speed range [rpm]
Display
Max. Stirring quantity [H2O, mL]
Motor rating input [W]
Motor rating output [W]
Max. Stirring bar [mm]
Set-up surface [mm]
Permissible ambient temperature [°C]
Permissible relative humidity
DIN EN60529 Protection class
Voltage [VAC]
Frequency [Hz]
Input power
Dimension [W x D x H, mm]
Weight [kg]
MI0102001D
1
Tempered glass
15 - 1500
OLED
1000
5
3
25
Φ100
5 - 40
80%
IP 65
100 - 240
50/60
6W
117 x 12 x 180
0.3
Technical Data