Four E's Scientific MI0103002 User manual

Operating Instructions
Oribital and Li near Shaker
MI0103002

Contents
Preface
Service
Warranty
1. Safety Instr uctions
2. Inspection
2.1 Receiving Inspection
2.2 Listing of Items
3. Control and Display
3.1 Control
3.2 Display
4. Operation
5. Faults
6. Maintenance and Cleaning
7. Associated standards and regulations
8. Specifications
9. Accessories
2
2
2
3
4
4
6
6
7
8
9
10
1

Preface
Please read the user mannual carefully before use, and follow
all operating and safety instructions!
Technical specifications and outline are subject to change
without prior notice
Service
When help needed , you can always contact us for technical
support.
Please provide the customer care representative with the
following information:
• Serial number ( on the rear panel )
• Descriptio n o f problem ( i.e., hardware or software )
• Your contact information
Warranty
This instrument is warranted to be free from defects in materials
and workmanship under normal use and service, for a period of
24 months from the date of invoice. The warranty is extended
only to the original purchaser. It shall not apply to any product or
parts which have been damaged on account of improper
installation, improper connections, misuse, accident or abnormal
conditions of operation.
For claims under the warranty,please contact your local supplier
or us directly.
2

1. Safety Instructions
Warning !
• Read the operating instructions carefully before use.
• Ensure that only trained staff works with the instrument.
Protective ground contact !
• Ensure the socket must be grounded (protective ground
contact) before use.
• When working wear personal safety guards to avoid the risk of:
- Splashing liquids
- Broken glass containers
• Follow the safety instructions, guidelines and accident prevention
regulations.
• Do not touch the running, moving instrument care not rolling your
fingers.
• Set up the instrument on a stable, clean, non-slip, dry and
fireproof surface. Do not operate the operate the instrument in
explosive atmospheres, with hazardous substances or under
water.
• If the instrument does not run smoothly, please decrease the
motor speed.
• Firmly secure the accessories and vessels in place to avoid
damage or risk.
• Only proce ss samples that will not react dangerously.
• Use the sta ndard accessories listed in the “accessories” section,
and follow the instructions to use accessories to ensure safety.
Please switch off the power before assembly of accessories,
confirm the instrument and accessories are intact before
switching on each time.
• The voltage stated on the nameplate must correspond to the
mains voltage.
• Do not cover the instrument during running.
• Keep the instrument away from the high magnetic field.
3

2. Inspection
2.1 Receiving Inspection
Unpack the instrument carefully and check for any damages
which may happen during transport. If any damage happens,
please contact us for technical support.
Note:
If there is any apparent damage to the system,
please do not connect to the power line.
2.2 Listing of Items
4
Qty
1
1
1
4
4
1
Items
Main unit
Power cable
User manual
Rubber plug
Column(Linear)
Universal attachment with 4 bar
3. Control and Display
3.1 Control
Items
Speed control knob
Timer control knob
Speed display
Time display
Power switch
Descriptions
Set target speed. Push down the knob
to start/stop the shaking function.
Set target time. Push down the knob to
start/stop the shaking function.
Display the set and real speed values.
Display the set and remain time values.
Switch ON/OFF instrument.

5
Speed display
Timer control
knob
Speed control
knob
Time display
Power switch
Linear Shaking
Orbital Shaking
Time Dispaly
speed Dispaly
Descriptions
Means motor blocked .
Means motor overspeed.
The displayed reading is for the set
value when it flashes and for the actual
value when it stops flashing
Display
Er 1
Er 2
Display area
3.2 Display

4. Operation
• Place the instrument on a safe and stable platform ensure the
required operating voltage and power supply voltage matched,
and the socket must be earthed reliably.
• Connect the power cable.
• Switch ON instrument.
• The instrument begins self-checking.
• When initialization is over, Digital displays the last running
values of spe ed.
• Rotate the speed control knob to set target speed.
Press the speed control knob to start shaking
Press the speed c ontrol knob again to stop shaking
• Rotate the timer control knob to set target time.
Press the timer control button to start shaking function at the
set speed and time. During operation, motion can be stopped
at any time by pressing the speed control knob or timer control
knob. If the timer control knob is pressed again, the shaking
function will start again and the timer will restart countdown.
When the timer reaches zero, the unitl will stop automatically
and ring the alarm .
If these operations above are normal, the instrument is
ready to operate. If not, the instrument may be damaged
during transportation, please contact us for the technical support
Note:
The speed value can be altered during shaking.
5. Faults
• When switched ON, the instrument does not work.
- Check whether the power cable is connected.
- Check whether the fuse is broken.
6

7
• Shaking suddenly stops.
- Digital displays “Er 01”, indicate the failure of “motor blocked”.
- Digital displays “Er 02”, indicate the failure of “motor
overspeed”
- Pressing the speed control knob or timer control knob first to
stop shaking , and then restart shaking with less load.If
shaking cannot start ,then repeat the process and gradually
reduce load.
6. Maintenance and Cleaning
• Proper maintenance can keep the instrume nt working properly
and lengthen its lifetime.
• Do not spray cleanser into the instrument when cleaning.
• Do not remove the power line when cleaning. Only use
recommended cleansers:
• Before using other method for cleaning or decontamination,
the user must ascertain with the manufacturer that this method
will not damage the instrument. Wear the proper protective
gloves during cleaning of the instrument.
Note:
• Electronic device cannot be clean with cleans er.
• If maintenance service required, the instrument
• must be cleaned first to avoid pollution of
• hazardous substances.
Dyes
Construction materials
Cosmetics
Foodstuffs
Fuels
Isopropyl alcohol
Water containing tenside / Isopropyl alcohol
Water containing tenside / Isopropyl alcohol
Water containing tenside
Water containing tenside

8
• If the instrument will not use for a long time, please
switch it off and place it in a dry, cleans,room
temperature and stable location.
7. Associated standards and regulations
Construction in accordance with the following safety standards:
EN 61010-1
UL 3101-1
CAN/CSA C22.2(1010-1)
EN 61010-2-10
Construction in accordance with the following EMC standards:
EN 61326-1
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.

8. Specifications
9
Items
Model
Shaking motion
Motor type
Max.load capacity with platform [kg]
Orbital diameter [mm]
Speed range [rpm]
Speed Display
Timer range
Timer Display
Operation type
Permissible ambient temperature [°C]
Permissible relative humidity
Protection class acc.to DIN EN60529
Voltage [VAC]
Frequency [Hz]
Power
Weight [kg]
Dimensions [W× D×H]
Specifications
MI0103002
Orbital / Linear
Brush less DC motor
7.5
10
30-500
Digital Display
0-99Hr59Min
Digital Display
Continuous / times
operation
5-40
80%
IP21
100-240
50/60
40
11
450x400x1065

10
9. Accessories
Cat. No.
MI0103002-101
MI0103002-102-1
MI0103002-102a
MI0103002-102b
MI0103002-102c
MI0103002-102d
MI0103002-102e
Descriptions
MI0103002 Universal
attachment
MI0103002 Fixing
clip attachment
MI0103002 Fixing clip
for flask volume 25 ml
MI0103002 Fixing clip
for flask volume 50 ml
MI0103002 Fixing clip
for flask volume 100 ml
MI0103002 Fixing Clip
for flask volume
200 /250ml
MI0103002 Fixing clip
for flask volume 500ml