FREE MOTION SFTL27808.0 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
Model No. SFTL27808.0
Serial No.
Write the serial number in the space
above for reference.
www.freemotionfitness.com
QUESTIONS?
If you have questions, or if parts are
damaged or missing, CONTACT
THE STORE WHERE YOU
PURCHASED THIS PRODUCT.
If you are unable to contact the
store, see HOW TO CONTACT
CUSTOMER CARE on the back
cover of this manual.
USER'S MANUAL

TABLE OF CONTENTS
WARNIN DECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS .................................................................3
BEFOREYOUBE IN .......................................................................5
ASSEMBLY ...............................................................................6
HOWTOUSETHECHESTPULSESENSOR ...................................................12
OPERATIONANDADJUSTMENT ............................................................13
HOWTOMOVETHETREADMILL ............................................................25
TROUBLESHOOTIN ......................................................................26
EXERCISE UIDELINES ...................................................................28
PARTLIST ...............................................................................30
EXPLODEDDRAWIN ......................................................................32
HOWTOCONTACTCUSTOMERCARE ...............................................BackCover
LIMITEDWARRANTY ..............................................................BackCover
These drawings show the locations of the
warning decals. If a decal is missing or il-
legible, see the back cover of this manual
and request a free replacement decal.
Apply the decal in the location shown.
Note: The decals may not be shown at ac-
tual size.
WARNING DECAL PLACEMENT
FREEMOTION is a registered trademark of ICON IP, Inc.
2
!
!

1. Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over age 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by per-
sons weighing 350 lbs. (159 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
11. When connecting the power cord (see page
13), plug the power cord into a surge suppres-
sor (not included) and plug the surge sup-
pressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
the back cover of this manual and order part
number 146148, or see your local electronics
store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 26 if the tread-
mill is not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. FreeMotion
Fitness assumes no responsibility for personal injury or property damage sustained by or through
the use of this product.
IMPORTANT PRECAUTIONS
3

18. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
19. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the “off” position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the reset/off circuit
breaker.)
21. Do not attempt to move the treadmill until it is
properly assembled. (See ASSEMBLY on page
6, and HOW TO MOVE THE TREADMILL on
page 25.) You must be able to safely lift 45 lbs.
(20 kg) to move the treadmill.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert or drop any object into any
opening on the treadmill.
25. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
26. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
4
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the revolutionary FREEMO-
TION®t5.8 treadmill. The t5.8 treadmill offers an im-
pressive selection of features designed to make your
workouts at home more enjoyable and effective.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the back cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Console
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Power Cord
Idler Roller
Adjustment Bolts
Pulse Sensor
Walking Platform
Accessory Tray

6
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key and your own Phillips screwdriver .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem-
bly. Extra hardware may be included.
3/8" Star
Washer (2)–6
#8 x 2 1/4" Machine Screw (3)–6
#8 x 1/2" Machine
Screw (4)–2
#6 x 5/8" Screw
(128)–2 3/8" x 3 1/4" Bolt (1)–6

7
2. Insert the end of the Upright Wire (111) through
the looped plastic ties at the top of the Upright
(81). Make sure that the Upright Wire is be-
hind the crossbar on the Upright. Then, gen-
tly pull up on the Upright Wire as you tighten the
plastic ties around the Upright Wire.
111
2
1. Make sure that
the Power Cord
(70) is unplugged
and lying on the
floor.
Slide the Upright Cover (not shown) off of the
Upright (81). Orient the Upright and the plastic
ties as shown. Set the Upright on the tabs on
the Frame (53). Attach the Upright to the Frame
with four 3/8" x 3 1/4" Bolts (1) and four 3/8"
Star Washers (2). Start all four Bolts before
tightening any of them. Be careful not to
pinch the Upright Wire (111).
81
53 111
1
12
2
Plastic Ties
81
Plastic Ties
Crossbar
1
70
!
!

8
4. Have a second person hold the handrail assem-
bly near the Upright (81). Insert the Upright Wire
(111) up through center of the handrail assem-
bly. Slide the bracket on the handrail assembly
over the crossbar on the Upright and set the
handrail assembly on the Upright. Be careful
not to pinch any wires.
Handrail
Assembly
4
3. Slide the Upright Cover (80) down onto the
Upright (81). Be careful not to pinch the
Upright Wire (111). Be careful not to hit the
ceiling.
111
80
3
81
81
Bracket
111
Crossbar

9
6. Have a second person hold the Console (101)
near the handrail assembly.
Connect the Upright Wire (111) and the handrail
wires to the console wires. Make sure that the
console wire and the handrail wire that you are
connecting have connectors that are the same
size. See the lower drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and
then try again. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
Insert the excess wires down into the Upright
Cover (80).
Set the Console (101) on the handrail assembly.
Be careful not to pinch any wires.
80
101
111
6
Console
Wires
111
Console
Wire
Handrail
Assembly
Handrail
Wires Handrail
Wire
5. Remove the two #8 x 1/2" Washer Head Screws
(23) and the Fan rill (102) from the Console
(101). The Washer Head Screws and the Fan
rill will be used in step 9.
5
23
102
101

7. Align the holes in the Console (101) with the
holes in the handrail assembly and the holes in
the Upright (not shown). Attach the Console and
the handrail assembly to the Upright with two
3/8" x 3 1/4" Bolts (1) and two 3/8" Star
Washers (2). Do not fully tighten the Bolts
yet. Note: It may be helpful to press the indi-
cated bracket against the Upright (81) and to
press down on the Console to align the
holes.
7101
81 Handrail
Assembly
1
2
Bracket
9. Reattach the Fan rill (102) to the Console
(101) with two #8 x 1/2" Washer Head Screws
(23). See the lower drawing. Make sure that
the teeth on the Fan Grill (102) sit inside the
grooves on the Upright Cover (80).
See step 7. Tighten the two 3/8" x 3 1/4"
Bolts (1).
9
23
102 101
10
Teeth
80
8. Tighten two #6 x 5/8" Screws (128) into the
Upright Cover (80) in the locations shown. Be
careful not to overtighten the Screws.
8
80
128

12. If necessary, move the treadmill to the desired
location (see HOW TO MOVE THE TREADMILL
on page 25).
After the treadmill is placed in the location where
it will be used, make sure that the Leveling Feet
(64) rest firmly on the floor. If the treadmill rocks
even slightly, loosen one of the 1/2" Nuts (36),
turn the Leveling Foot clockwise or counter-
clockwise until the rocking motion is eliminated,
and retighten the Nut.
64
12
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see page 27).
36
11. Tighten two #8 x 1/2" Machine Screws (4) into
the bottom of the handrail assembly. Be careful
not to overtighten the Machine Screws.
See step 10. Tighten the six #8 x 2 1/4"
Machine Screws (3). Be careful not to over-
tighten the Machine Screws.
11
Handrail
Assembly
4
4
3
10
Handrail
Assembly
86
3
10. Remove the packaging from the Handrail Cover
(86). Attach the Handrail Cover to the handrail
assembly with six #8 x 2 1/4" Machine Screws
(3). Start all six Machine Screws but do not
tighten them yet.
11

12
HOW TO PUT ON THE CHEST PULSE SENSOR
The chest pulse sensor consists of two components—
the chest strap and the sensor unit.
Insert the tab on one end of the chest strap into the
hole in one end of the sensor unit, as shown in the inset
drawing above. The tab should be flush with the front of
the sensor unit.
Next, wrap the chest
pulse sensor around
your chest and attach
the other end of the
chest strap to the
sensor unit. Adjust
the length of the
chest strap, if neces-
sary. The chest pulse
sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens so-
lution, wet both electrode areas. Return the sensor unit
to a position against your chest.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° F (50° C) or below 14°
F (-10° C).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain
how the chest pulse sensor is used with the con-
sole. If the chest pulse sensor does not function
properly, try the steps below.
• Make sure that you are wearing the chest pulse sen-
sor as described at the left. Note: If the chest pulse
sensor does not function when positioned as de-
scribed, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, rewet the electrode areas.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within armʼs length of the console.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
Chest Strap
Tabs
Sensor Unit
Tab
Sensor
Unit Buckle
HOW TO USE THE CHEST PULSE SENSOR

13
OPERATION AND AD USTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see the
back cover of this manual and order part number
146148, or see your local electronics store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
rounded Outlet Box
rounded Outlet Box
rounding Plug
Surge Suppressor
Surge Suppressor
rounding Pin
Adapter
Lug
Metal Screw
rounded Outlet
rounding Pin

14
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When you use the manual mode of
the console, you can change the speed and incline of
the treadmill with the touch of a button. As you exer-
cise, the console will display continuous exercise feed-
back. You can even measure your heart rate using the
handgrip pulse sensor or the chest pulse sensor (see
page 12 for information on the chest pulse sensor).
In addition, the console features fourteen personal
trainer workouts. Each preset workout automatically
controls the speed and incline of the treadmill as it
guides you through an effective exercise session.
The console also offers twelve interactive trainer work-
outs that allow you to customize your workout. The in-
teractive trainer workouts include three heart rate
workouts that control the speed and incline of the
treadmill to keep your heart rate near the target heart
rate settings. In addition, three fitness test workouts
measure your fitness level or your VO2max.
The console also features the new iFit interactive work-
out system. The iFit system is compatible with iFit inter-
active workout cards containing workout programs de-
signed to help you achieve specific fitness goals. For
example, lose unwanted pounds with the iFit Weight
Loss program, or train for a long-distance run with the
iFit Marathon program. iFit programs automatically
control the speed and incline of the treadmill. To pur-
chase iFit cards, please see the back cover of this
manual or go to www.iFit.com. iFit cards are also
available at select stores.
Whether you select the manual mode or a preset work-
out, you can listen to your favorite workout music or
audio books with the consoleʼs stereo sound system.
To turn on the power, see page 15. To use the man-
ual mode, see page 15. To use a personal trainer
workout, see page 17. To use a walk/run workout or
a manual control workout, see page 19. To use a
fitness test workout, see page 20. To use a heart
rate workout, see page 21. To use a custom work-
out, see page 22. To use an iFit workout, see page
23. To use the maintenance mode, see page 24. To
use the stereo sound system, see page 24.
CONSOLE
DIAGRAM

15
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord
(see page 13). Next,
locate the reset/off cir-
cuit breaker on the
treadmill frame near
the power cord. Make
sure that the circuit
breaker is in the “reset” position.
Next, stand on the foot
rails of the treadmill.
Locate the clip at-
tached to the key (see
the drawing at the
right), and slide the clip
securely onto the
waistband of your
clothes. Then, insert
the key into the console. After a moment, the displays
will light. IMPORTANT: In an emergency situation,
the key can be pulled from the console, causing
the walking belt to slow to a stop. Test the clip by
carefully taking a few steps backward; if the key is
not pulled from the console, adjust the position of
the clip.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To pre-
vent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment
of the walking belt, and center the walking belt if
necessary (see page 27).
Note: The console will display speed and distance in
either miles or kilometers. For simplicity, all instruc-
tions in this section refer to miles.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
The incline will automatically rise the maximum in-
cline level and then return to the minimum incline
level.
2. Select the manual mode.
Each time the key
is inserted, the
manual mode will
be selected. If you
have selected a
workout, press any
of the workout buttons repeatedly until zeros ap-
pear in the display.
3. Start the walking belt and adjust the speed.
To start the walking belt, press the Start/Stop but-
ton, the Speed increase button, or one of the
Precision Quick Touch Speed buttons numbered 1
to 12.
If you press the Start/Stop button or the Speed in-
crease button, the walking belt will begin to move
at 1 mph. As you exercise, change the speed of
the walking belt as desired by pressing the Speed
increase and decrease buttons. Each time you
press a button, the speed setting will change by
0.1 mph; if you hold down the button, the speed
setting will change in increments of 0.5 mph.
If you press one of the numbered Precision Quick
Touch Speed buttons, the walking belt will gradu-
ally change speed until it reaches the selected
speed setting. To select a speed setting that in-
cludes a decimal—such as 3.5 mph—press two
numbered buttons in succession. For example, to
select a speed setting of 3.5 mph, press the 3 but-
ton and then immediately press the 5 button.
To stop the walking belt, press the Start/Stop but-
ton. To restart the walking belt, press the
Start/Stop button, the Speed increase button, or
one of the numbered Precision Quick Touch Speed
buttons.
Clip
Key
Reset
Position

16
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the Quick Touch Incline buttons numbered 0 to 15.
Each time you press the Incline increase or de-
crease button, the incline will change by 0.5%. If
you press one of the numbered Quick Touch
Incline buttons, the incline will gradually change
until it reaches the selected incline setting.
5. Select a display mode and monitor your
progress with the display.
When the manual
mode is selected,
the console offers
six display modes.
The display mode
that you select will
determine which workout information is shown.
Press the Display button repeatedly to select the
desired display mode.
As you walk or run on the treadmill, the upper dis-
play can show the following workout information:
• The elapsed time.
• The distance that you have walked or run.
• The speed of the walking belt.
• The incline level of the treadmill.
• The approximate number of calories you have
burned.
• The approximate number of calories burned per
hour.
• Your exercise intensity in METs. One MET is the
amount of energy you use while resting.
• Your walking or running pace, in minutes per
mile or minutes per kilometer.
Regardless of which display mode you select, the
speed or incline setting will appear in the display
for a few seconds each time you change the set-
ting.
The lower right and lower left displays will show the
speed of the walking belt and incline of the tread-
mill.
As you switch between workouts and the manual
mode, the console will keep track of the total dis-
tance that you have walked or run and the approxi-
mate number of calories you have burned. You can
keep your totals even when you switch to a new
workout. To reset the console, press the Clear but-
ton.
6. Measure your heart rate if desired.
Note: If you use the handgrip pulse sensor and
the chest pulse sensor at the same time, the
console will not display your heart rate accu-
rately. See page 12 for information on the chest
pulse sensor.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from
the metal con-
tacts. In addi-
tion, make
sure that your
hands are clean.
To measure your heart rate, stand on the foot
rails and hold the contacts for approximately
ten seconds—avoid moving your hands. When
your pulse is detected, a heart-shaped indicator
will flash in the display and your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
Contacts

17
7. Turn on the fan if desired.
The fan has high and low speed settings. Press the
Fan button repeatedly to select a fan speed or to
turn off the fan. Note: If the fan is on when the
walking belt stops, the fan will automatically turn off
after a few minutes.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Start/Stop button,
remove the key from the console, and put it in a se-
cure place. The incline will automatically rise the
maximum incline level and then return to the mini-
mum incline level.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
HOW TO USE A PERSONAL TRAINER WORKOUT
1. Insert the key into the console.
See step 1 on page 15.
2. Select one of the personal trainer workouts.
To select a per-
sonal trainer work-
out, press the
Interval Workouts
button, the Terrain
Workouts button, or
the Random Workouts button repeatedly until the
name of the desired workout appears in the dis-
play. Interval workouts use speed settings to pro-
vide a personalized workout. Terrain workouts use
speed and incline settings to simulate an actual
walking experience. Random workouts use preset
speed and incline settings.
When a workout is selected, the display will show
the name, the maximum incline setting, the maxi-
mum speed setting and the duration of the work-
out. The display will also show a profile of the
speed settings of the workout.
Press the Enter button to select the desired work-
out. Select your age, your weight, and the workout
duration using the increase and decrease buttons
next to the Enter button. Press the Enter button
after each selection. Note: To use the Interval
workouts, you must also enter your minimum and
maximum speed settings using the Precision Quick
Touch Speed buttons or the Speed increase and
decrease buttons.

18
3. Press the Start/Stop button to start the workout.
A moment after you press the Start/Stop button,
the treadmill will automatically adjust to the first
speed and incline settings of the workout. Hold the
handrails and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed and/or incline
setting may be programmed for consecutive seg-
ments.
During the workout,
the profile will show
your progress. The
flashing segment
of the profile repre-
sents the current
segment of the workout. The height of the flashing
segment indicates the speed setting for the current
segment. At the end of each segment, a series of
tones will sound and the next segment of the profile
will begin to flash. If a new speed or incline setting
is programmed for the next segment of the workout,
the speed or incline setting will appear at the top of
the display for a few moments to alert you.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Speed or
Incline buttons; however, when the next segment
of the workout begins, the treadmill will auto-
matically adjust to the speed and incline set-
tings for the next segment. Note: If you use an
Interval workout, the incline will not adjust automati-
cally.
To stop or restart the workout at any time, press
the Start/Stop button.
4. Select a display mode and monitor your
progress with the display.
The console offers three display modes. The dis-
play mode that you select will determine which
workout information is shown. Press the Display
button repeatedly to select the desired display
mode.
The display can show the speed of the walking belt,
the incline of the treadmill, a profile of the speed
settings of the workout, the time remaining in the
workout, the distance you have walked or run, the
approximate number of calories you have burned,
your exercise intensity in METs, the approximate
number of calories burned per hour, your pace, and
your power output in watts.
5. Measure your heart rate if desired.
See step 6 on page 16.
6. Turn on the fan if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.
Current Segment

19
HOW TO USE A WALK/RUN WORKOUT OR A
MANUAL CONTROL WORKOUT
1. Insert the key into the console.
See step 1 on page 15.
2. Select one of the workouts.
To select a walk/run workout, press the Walk/Run
Workouts button repeatedly until the 5K Walk, the
10K Run, or the Cross Country workout appears in
the display.
To select a manual
control workout,
press the Manual
Control button re-
peatedly until the
Manual Time, the
Manual Distance, or the Manual Calories workout
appears in the display. The display will show the
name, and the time, distance, or calorie goal of the
workout.
Press the Enter button to select the desired work-
out. Select your age and then your weight using
the increase and decrease buttons next to the
Enter button. Press the Enter button after each
selection. Note: To use the cross country work-
outs, you must also enter your distance goal. To
use a manual control workout, enter your time, dis-
tance, or calorie goal.
3. Press the Start/Stop button to start the workout.
A moment after you press the Start/Stop button,
the treadmill will begin moving. Hold the handrails
and begin walking.
During the workout, the profile will show the speed
of the walking belt. As you exercise, change the
speed and incline of the walking belt as desired by
pressing the Speed and Incline buttons.
The workout will continue until you reach your time,
distance, or calorie goal. The walking belt will then
slow to a stop.
To stop or restart the workout at any time, press
the Start/Stop button.
4. Select a display mode and monitor your
progress with the display.
See step 4 on page 18.
5. Measure your heart rate if desired.
See step 6 on page 16.
6. Turn on the fan if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.

20
HOW TO USE A FITNESS TEST WORKOUT
The fitness test workouts measure your relative fitness
level. For the most accurate results, use a fitness test
workout when you are not feeling tired, when you have
not eaten for at least two hours, and when you have not
exercised for at least 24 hours.
The treadmill features three fitness workouts. The
Ebbeling Fitness Test measures VO2max, or aerobic
capacity, and lasts 9 minutes. The erkin Fitness Test
also measures VO2max. The erkin Fitness Test be-
gins with a three-minute warm-up period and ends after
either 14 minutes or when you reach a certain heart
rate. The FreeMotion Fitness Test measures your fit-
ness level on a scale of 1 to 10. The FreeMotion
Fitness Test ends after either 28 minutes or when you
reach a certain heart rate.
1. Put on the chest pulse sensor.
To use a fitness test, you must wear the chest
pulse sensor or use the handgrip pulse sensor.
Note: For best results, you should wear the chest
pulse sensor.
2. Insert the key into the console.
See step 1 on page 15.
3. Select a fitness test workout.
To select a fitness test workout, press the Fitness
Tests button repeatedly until the name of the de-
sired fitness test appears in the display.
Press the Enter button to select the desired work-
out. Select your age and then your weight using
the increase and decrease buttons next to the
Enter button. Press the Enter button after each
selection. Note: To use the Ebbeling Fitness Test,
you must also enter your gender.
4. Press the Start/Stop button to start the workout.
A moment after you press the Start/Stop button,
the treadmill will automatically adjust to the first
speed and incline settings of the fitness test. Begin
walking on the treadmill. Note: For the most accu-
rate results, do not hold the handrails during a fit-
ness test workout.
During the workout, the speed and incline of the
treadmill will periodically change. The speed set-
ting or the incline setting will appear in the display
to alert you before each change. IMPORTANT:
The Speed and Incline buttons will not function
during a fitness test workout.
Note: If you press the Start/Stop button during the
fitness test, the fitness test will end.
When the workout ends, the walking belt will slow
to a stop and your fitness level or VO2max will ap-
pear in the display.
If your pulse is not detected during the workout, the
words CHECK HEART RATE MONITOR will ap-
pear in the display and the speed of the treadmill
may automatically decrease. If your pulse is still not
detected, the fitness test will be aborted.
5. Select a display mode and monitor your
progress with the display.
See step 4 on page 18. Note: The fitness tests will
display your fitness level instead of your exercise
intensity in METs. The console may display a “W”
when you are warming up or a “C” when you are
cooling down.
6. Turn on the fan if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.