Freescale Semiconductor Kinetis TWR-K24F120M User manual

Quick Start Guide
TWR-K24F120M
Low-power MCU Platform with
High RAM Density for Connectivity
and Sensor Fusion Applications
TOWER SYSTEM

2
Quick Start Guide
Get to Know the TWR-K24F120M
K24F
Micro-USB
Reset
Button (SW3)
Power/Open
SDA Micro-USB
K20 OpenSDA
Debug
K24F JTAG
Power
Selection
K24FN256VDC12 MCU
Audio
Out/Mic
Audio In
Potentiometer
General Purpose
TWRPI Plug-In
Accelerometer
+ Magnetometer
Primary
Connector
Secondary
Connector
Pushbutton
(SW2)
Pushbutton
(SW1)
LEDs
Figure 1: Front side of TWR-K24F120M

3
TOWER SYSTEM
TWR-K24F120M
Freescale Tower System
The TWR-K24F120M MCU module is designed to work either in stand-alone
mode or as part of the Freescale Tower System, a modular development platform
that enables rapid prototyping and tool re-use through reconfigurable hardware.
Begin constructing your Tower System today by visiting freescale.com/Tower for
additional Tower System MCU modules and compatible peripherals.
Figure 2: Back side of TWR-K24F120M
Battery
Receptacle
for VBAT

4
Quick Start Guide
TWR-K24F120M Features
• K24FN256VDC12 MCU (120 MHz, 256 KB Flash, 256 KB RAM, low power,
121 MAPBGA thin-profile package)
• Dual-role USB interface with micro-AB USB connector
• General-purpose Tower plug-in (TWRPI) socket
• On-board debug circuit: K20DX128VFM5 OpenSDAv2 with virtual serial port
• Three-axis combination accelerometer and magnetometer (FXOS8700CQ)
• Four (4) user-controllable LEDs plus RGB LED
• Two (2) user pushbutton switches for GPIO interrupts
• On-board Freescale SGTL5000 audio codec
• 16 Mbit SPI serial flash memory
• Li-Ion battery charging circuit (battery not included)
• One (1) user pushbutton switch for MCU reset
• Potentiometer
• Independent, battery-operated power supply for real-time clock (RTC) module

5
TOWER SYSTEM
In this quick start guide, you will learn how to set up the TWR-K24F120M
module and run the included demonstrated software. For more detailed
information, review the user manual at freescale.com/TWR-K24F120M.
Step-by-Step Installation Instructions
Download and Install
the Serial Driver
The directions and link to the latest
ARM
®
mbed
™
serial port driver can
be found at: mbed.org/handbook/
Windows-serial-configuration
Configure the
Hardware
Install the included battery into the
VBAT (RTC) battery holder. Connect
one end of the USB cable to the
PC and the other end to the Power/
OpenSDAv2 micro-AB connector on
the TWR-K24F120M module. Allow
the PC to automatically configure the
USB drivers if needed.
21

6
Run the
Quick Start Demo
Set up the serial port connection on your
terminal program for 115200 baud rate,
8-bit data, no parity, 1 stop bit.
Press the reset button on the board to
display the following message:
Select from the following menu:
1: Audio demo
2: Bubble level
3: eCompass demo
4: Metal Detector demo
5: Stopwatch demo
Enter a number key (1–5) on the keyboard
to run each option from the Quick
Start Demo. Further information will be
displayed on the terminal as the demo runs.
Step-by-Step Installation Instructions (continued)
Quick Start Guide
3

7
TOWER SYSTEM
TWR-K24F120M Jumper Options
The following is a list of all jumper options available on the TWR-K24F120M. The default
installed jumper settings are indicated by white text within the red boxes.
Jumper Option Setting Description
J33 Debug target
power
ON Connect P5V_TRG_SDA to target power
OFF Disconnect P5V_TRG_SDA from target power
J15 Enable USB
power
ON Connect PTB23 to USB power enable on power switch MIC2005
OFF Disconnect PTB23 from USB power enable on power switch MIC2005
J19 USB ID
connection
ON Connect PTD7 to USB ID pin
OFF Disconnect PTD7 from USB ID pin
J16 USB over-
current flag
ON Connect PTB22 to over-current flag on power switch MIC2005
OFF Disconnect PTB22 from over-current flag on power switch MIC2005
J21 USB switch
1-2 Connect MCU USB0_DP and USB0_DM pins to micro-USB
connector (J23)
2-3 Connect MCU USB0_DP and USB0_DM pins to Tower Elevator
J26 VREGIN input
to processor
1-2 Connect P5V0_VREGIN_K24 to MCU VREGIN pin
2-3 Connect on-board regulator output P3V3_REG to MCU VREGIN pin
J28 P5V0_ VREGIN_K24
selection
5-6 5V MCU input from on-board USB connector (J23)
6-8 5V MCU input from tower USB VBUS
4-6 & 1-3 5V from OpenSDA USB/TWR 5V (P5V_TRG_SDA)

8
Quick Start Guide
Jumper Option Setting Description
J28
3.3V regulator
input selection
1-2 5V from OpenSDA USB/TWR 5V (P5V_TRG_SDA)
3-5 & 2-4 5V power from on-board USB connector (J23)
J27
MCU power
selection
3-4 3.3V from regulator
1-3 VOUT_3V3 (from MCU)
3-5 1.8V from regulator
J27
Rechargeable
battery
selection
6-8 Rechargeable battery powers input to 3.3V regulator
4-6 Rechargeable battery powers input to 1.8V regulator
J30
MCU VDD
current
measurement
ON Connect V_BRD to MCU_PWR
OFF Allow current measurement on MCU VDD
J29
VDDA and
VREFH power
ON Connect V_BRD to VDDA and VREFH
OFF Disconnect V_BRD from VDDA and VREF
J17 VBAT power
1-2 Connect VBAT to MCU_PWR
2-3 Connect VBAT to the higher voltage between MCU_PWR and
coin-cell battery (P3V0_COINCELL)
J3
LED
connections
1-2 Connect PTD4 to Yellow LED (D7)
3-4 Connect PTD5 to Red LED (D4)
5-6 Connect PTD6 to Orange LED (D3)
7-8 Connect PTD7 to Yellow/Green LED (D2)
TWR-K24F120M Jumper Options (continued)

9
TOWER SYSTEM
Jumper Option Setting Description
J2
Audio codec
power
ON Supply 3.3V power to audio codec
OFF Remove power from audio codec. Audio codec cannot be used when operating the board at 1.8V. So J2 should be OFF for 1.8V
board operation.
J13
TWRPI current
measurement
ON Connect V_BRD to TWRPI 3-V power (GPT_VBRD)
OFF
Disconnect V_BRD from TWRPI 3-V power (GPT_VBRD) to measure
TWRPI current
J5
Accelerometer/
magnetometer*
I
2
C SCL
connection
ON Connect PTE24 to I
2
C_SCL_SNSR
OFF Disconnect PTE24 from I
2
C_SCL_SNSR
J6
Accelerometer/
magnetometer
I
2
C SDA
connection
ON Connect PTE25 to I
2
C_SDA_SNSR
OFF Disconnect PTE25 from I
2
C_SDA_SNSR
J9
Accelerometer/
magnetometer
I
2
C slave
address SA0
ON Pull accelerometer/magnetometer SA0 low
OFF Pull accelerometer/magnetometer SA0 high
J8
Magnetometer
slave address
SA1
ON Pull magnetometer SA1 high
OFF Pull magnetometer SA1 low (also used for accelerometer GND)
J12
Accelerometer/
Magnetometer
I
2
C interrupt 1
ON Connect PTB0 to INT1
OFF Disconnect PTB0 from INT1
J10
Accelerometer/
Magnetometer
I
2
C interrupt 2
ON Connect PTB1 to INT2
OFF Disconnect PTB1 from INT2
TWR-K24F120M Jumper Options (continued)

10
Quick Start Guide
Jumper Option Setting Description
J1
Potentiometer
enable
ON Connect PTB2 to POT_5K
OFF Disconnect PTB2 from POT_5K
J40
Reset push
button
1-2 Connect SW3 to SDA_RST_TGTMCU_J_B
2-3 Connect SW3 to RST_TGTMCU_B
J38
SWD_DIO
isolation
ON Connect SWD_DIO_TGTMCU_BUF to SWD_DIO_TGTMCU
OFF Disconnect SWD_DIO_TGTMCU_BUF from SWD_DIO_TGTMCU
J34
SWD_CLK
isolation
ON Connect SWD_CLK_TGTMCU_BUF to SWD_CLK_TGTMCU
OFF Disconnect SWD_CLK_TGTMCU_BUF from SWD_CLK_TGTMCU
J25
UART RX
selection
1-2 Connect UART1_RX_TGTMCU to UART1_RX_ELEV_BUF
(Tower Elevator)
2-3
Connect UART1_RX_TGTMCU to UART1_RX_TGTMCU_BUF
(OpenSDA)
J22
UART TX
selection
1-2 Connect UART1_TX_TGTMCU to UART1_TX_ELEV_BUF
(Tower Elevator)
2-3
Connect UART1_TX_TGTMCU to UART1_TX_TGTMCU_BUF
(OpenSDA)
J7
RESET-OUT_B
selection
1-2 Connect Tower Elevator RESET_OUT_B to PTA14
2-3 Connect Tower Elevator RESET_OUT_B to PTA17
TWR-K24F120M Jumper Options (continued)

11
TOWER SYSTEM
Expanded Software and
Tools Now Available for
Kinetis MCUs
To take your design to the next level,
leverage the Kinetis SDK and other
online enablement software and tools
for Kinetis MCUs, available for download
at the relevant links listed here.
• Kinetis SDK at
freescale.com/KSDK
• MQX
™
RTOS at
freescale.com/MQX
• Kinetis Design Studio IDE at
freescale.com/KDS
• Bootloader for Kinetis MCUs at
freescale.com/Kboot
Get Started
Download installation software and documentation for the
Quick Start Demo under “Jump Start Your Design” at
freescale.com/TWR-K24F120M.

For more information, visit
freescale.com/TWR-K24F120M, freescale.com/Kinetis
or freescale.com/Tower
Join the online Tower community at towergeeks.org
Freescale, the Freescale logo, CodeWarrior, the Energy Efficient Solutions logo
and Kinetis are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat.
& Tm. Off. Tower is a trademark of Freescale Semiconductor, Inc. All other
product or service names are the property of their respective owners. ARM and
mbed are registered trademarks of ARM Limited in the EU and/or elsewhere.
All rights reserved. © 2014 Freescale Semiconductor, Inc.
Doc Number: TWRK24F120MQSG REV 0
Agile Number: 926-78862 Rev A
Support
Visit freescale.com/support for a list of phone
numbers within your region.
Warranty
Visit freescale.com/warranty for complete
warranty information.
Quick Start GuideQuick Start Guide