Friedrich Z-Star ZQ05 User manual

Room Air Conditioner
Installation and Operation
Manual
MODEL NUMBER SERIAL NUMBER PURCHASE DATE
ZStar®
920-095-03 (12/02)
ZQ05115 Volts ZQ07
Registering Your Room Air Conditioner
Model information can be found on the name plate located on the
side of the unit near the control panel. Please complete and mail
the owner registration card furnished with this product or register
on-line at www.friedrich.com (USA only). For your future
convenience, record the model information here.
ENGLISH FRANÇAIS ESPAÑOL

ENGLISH
Congratulations!
You have purchased a Friedrich ZStar®
room air conditioner. The Friedrich
ZStar®is designed to give maximum
comfort and quietness.
Table of Contents
Introduction ..................................................................................2
Safety Precautions.......................................................................3
How to operate your Friedrich ZStar
®
.......................................5
Installation Instructions...............................................................7
Troubleshooting Tips.................................................................11
Warranty......................................................................................12

Before Operating Your Unit
Make sure the wiring is adequate for your unit.
If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that
the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in figure 1.
DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical power to the unit; an extension cord will not.
Make sure that the receptacle is compatible with the wall plug provided.
This insures proper grounding. If you have a two-prong receptacle you will need to have the circuit replaced
by a certified electrician with a grounded circuit that meets all national and local codes and ordinances. You
must use the three-prong plug furnished with the air conditioner.
Figure 1
For the Best Cooling Performance and Energy Efficiency
Keep the filter clean
Make sure that your air conditioner is always in top performing condition by cleaning the filter regularly.
Instructions for removing and cleaning the filter can be found on page 6.
Provide good airflow
Make sure that the airflow to and from the unit is clear. Your air conditioner puts the air out at the top of
the unit, and takes in air at the bottom. Airflow is critical to good operation. It is just as important on the
outside of the building that the airflow around the unit exterior is not blocked.
Unit Placement
If your air conditioner can be placed in a window or a wall that is shaded by a tree or another building, the
unit will operate even more efficiently. Using drapes or blinds on the sunny side of the dwelling will also
add to your unit's efficiency.
Insulation
Good insulation will be a big help in maintaining desirable comfort levels. Doors should have weather
stripping. Be sure to caulk around doors and windows.
2
Introduction
MODEL
ZQ05
ZQ07
AMP VOLT NEMA NO.
15 125 5-15P
CIRCUIT
RATING OR
TIME DELAY
FUSE PLUG FACE

ENGLISH
3
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be
followed.
■Incorrect operation due to ignoring of instruction will cause harm or damage, the seriousness is classified
by the following indications.
WARNING
WARNING This symbol indicates the possibility of death or serious injury.
CAUTION This symbol indicates the possibility of injury or damage to
properties only.
■Meanings of symbols used in this manual are as shown below.
Never Do This
Always Do This
Plug in the power plug
properly.
•Otherwise,itwillcauseelectric
shock or fire due to heat
generation.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
• It will cause electric shock or fire
due to heat generation.
Do not damage or use an
unspecified power cord.
• It will cause electric shock or fire.
• If the power cord is damaged, it must
be replaced by the manufacturer or a
Friedrich-certified service agent.
Do not modify power cord
length or share the outlet
with other appliances.
• It will cause electric shock or fire
due to heat generation.
Do not operate with wet
hands or in damp
environment.
• It will cause electric shock.
Do not direct air flow at room
occupants only.
•
This could lead to health problems .

4
Safety Precautions
Sharp
edges
When the air filter is to be
removed, do not touch the
metal parts of the unit.
•They are sharp and may cause
an injury.
Do not clean the air
conditioner with water.
•Water may enter the unit and
degrade the insulation. It may
causeanelectricshock.
Whentheunitistobe
cleaned, switch the unit off,
and unplug it.
•Since the fan rotates at high
speed during operation, it may
causeaninjury.
Do not operate the unit
without the air filter or when
the front intake grille has
been removed.
•It could cause dust to
accumulate on the heat
exchanger.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
•This could injure the pets
or plants.
Do not use for special
purposes.
•Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects.
It may cause deterioration of
quality, etc.
Do not operate switches
with wet hands .
•It may cause an electric shock.
Do not apply an insecticide
or flammable spray.
•It may cause a fire or
deformation of the cabinet.
SHARP EDGES!
The edges of the case can
be SHARP!
•Use caution when handling the
case.Gripitfirmlyanddonotallow
it to slip while holding it.
• Use heavy gloves to handle
the case if necessary.
• DO NOT
allow the
case to slide
against
your skin!

ENGLISH
5
How to operate your Friedrich ZStar®
Hi
Fan
Lo
Fan
Hi
Cool
Off
Lo
Cool
Temperature
Mode
Warmer Cooler
O
O
Function Controls
When the air conditioner has finished cooling the room and is turned off or set to the fan
position, wait at least 3 minutes before resetting to the cooling operation again.
FUNCTION CONTROL
This dial allows you to select 2 cooling and 2 fan speeds.
Turn to Off to turn everything off.
Turn to Hi Cool for quick cooling.
Turn to Lo Cool to maintain a desired temperature.
The Hi Fan setting provides maximum circulation of filtered room air
without cooling.
The Lo Fan setting is a slow fan speed without cooling.
TEMPERATURE CONTROL
This dial is the thermostat. Turn it clockwise for cooler and
counterclockwise for a warmer temperature.
•FOR NORMAL COOLING
1. Turn the Mode switch to the Hi Cool or the Lo Cool setting.
2. Set the Temperature control to the desired temperature point (the mid-point is a good
starting position). If the room temperature is not satisfactory after a reasonable time, adjust the
control to a cooler or warmer setting, as appropriate.
•FOR MAXIMUM COOLING
1. Turn the Mode switch to the Hi Cool setting.
2. Set the temperature control to the coolest temperature point (all the way to the right).
•FOR QUIETER OPERATION
1. Turn the Mode switch to the Lo Cool setting.
2. Set the Temperature control as needed.
CAUTION

6
How to operate your Friedrich ZStar®
Do not force
open or open too
far (about 56°)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Additional controls and important information.
Care and Maintenance
Air Direction
• ADJUSTING THE AIR DIRECTION USING THE HORIZONTAL AIR-DEFLECTOR CONTROL
Using the Control Tabs, the air flow can be directed
to the left, right, straight ahead, or any combination
of these directions.
TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.
•To Remove the Filter
1. Remove the front cover by gripping the top outside
edges and pulling toward you (see Fig.1).
You will notice that the grille will only open to
about 56°. Do not force the grille open too far.
2. Find the two clips that hold the filter in place.
Gently lift the filter out.
•To Clean the Filter
1. Clean with warm water. Be sure to shake all water off
before replacing the filter.
2. Carefully position the filter, bottom first, and snap
back into place.
The filter should be cleaned every two weeks for best
results.
•Cleaning The Air Conditioner
The front grille and Inlet grille may be wiped with a
cloth dampened in a mild detergent and lukewarm water
solution. (Fig. 2)
The cabinet may be washed with mild soap or detergent and
lukewarm water.
To ensure continued peak efficiency, the condenser
coils(outside of unit) should be checked periodically and
cleaned if clogged with soot or dirt from the atmosphere.
Consult a certified Friedrich service agent for more information.
•Removing the Front Grille
1. Remove the temperature and mode control knobs by gently
pulling them off.(Fig.3)
2. Remove the screw securing the Front Grille.(Fig.3) The screw is
located behind the bottom temperature knob.
3. Push the grille up from the bottom and pull the top of the grille
away from the case as the top tabs lift out of their slots.(Fig. 4)
4. Carefully position the grille, bottom first, and snap back into
place.
5. Reposition the screw that secures the front grille and replace the
knobs.

ENGLISH
7
1
8
6
5
3
2
7
9
4
Learning the key components will help you properly install the unit.
Features
1. CABINET
2. HORIZONTAL AIR DEFLECTOR
3. COOL AIR DISCHARGE
4. FRONT GRILLE
5. INLET GRILLE
6. AIR FILTER
7. KNOBS
8. AIR INTAKE
9. UPPER GUIDE
Installation Instructions

8
Installation Instructions
OUTDOORSINDOORS
INNER
SILL
OUTER
SILL
INNER
SILL
WOOD STRIP MOUNTED
ON TOP OF INNER SILL
WOOD STRIP
FOR
L BRACKET
3/4"
CLEARANCE
1" MAX.
STORM
WINDOW
FRAME
OUTDOORSINDOORS
OUTER
SILL
TYPE B: 5EA
(WOOD SCREW)
HARDWARE
TYPE A: 11EA
(SHORT SCREW) TYPE C: 3EA ( L BRACKET)
TYPE E: 1EA
(SASH SEAL)
(Not adhesive backed)
TYPE D: 1EA
(SEAL STRIP)
(Adhesive backed)
TYPE F: 2EA
(GUIDE PANEL) TYPE G: 1EA (SUPPORT BRACKET)
10mm
16mm
Fig. 5-1 Fig. 5-2
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
1. This unit is designed for installation in standard double hung windows with actual opening widths of
22" to 36". The upper and lower sash must open sufficiently to allow a clear vertical opening of 13"
from the bottom of the sash to the window stool.
2.If storm window presents interference, fasten a 2" wide wood strip to the inner window sill across
the full width of the sill. The wood strip should be thick enough to raise the height of the window sill
so that the unit can be installed without interference by the storm window frame.
See Fig. 5-2. The top of the wood strip should be approximately 3/4" higher than the storm window
frame (STORM WINDOW FRAME) or wood strip (OUTDOORS) to help condensation to drain
properly to the outside.
3. Install a second wood strip (approximately 6" long by 11/2" wide and same thickness as first strip) in
the center of the outer sill flush against the back off the inner sill. This will raise the Lbracket as
shown Fig. 5-2.
4. If the distance between STORM WINDOW FRAME and WOOD STRIP MOUNTED ON TOP OF
INNER SILL is more than 1", two of wood strips are not necessary.
Window Requirements
Installation