Friedrich ZoneAire Compact P08S User manual

Table of Contents
Important Safety Guidelines………….………. 2
Introduction……………………………………………. 3
Unpacking Instructions & Contents .………. 4
Parts ……………............................................ 5
Display Functions …………………………………… 6
Remote Control Functions ………..…..………. 9
Drain Pipe ………………………….……..…..………. 12
Maintenance & Cleaning………………………... 13
Installation …………………………………………….. 14
Troubleshooting…………………………………….. 16
P08S/P10S Owner’s Manual
98081002_02

IMPORTANT
Do not install and use your portable air conditioner unit before carefully reading this instruction guide.
Please retain this manual brochure for product warranty and future reference
IMPORTANT SAFETY GUIDELINES
2
CAUTION
Operate this unit in an ambient of 89°F or less.
The heating function of the unit should be
operated in an indoor ambient temperature
between 44°F and 73°F.
Clean air filter periodically to enjoy the most
efficient cooling.
When the unit is shut off, please wait at least 3.5
minutes before restarting; this is to prevent the
compressor from being damaged.
This unit is for indoor cooling, heating and
dehumidifying.
When turning on the unit, the fan will operate but
the compressor will start up after the cooling
alarm flashes for three minutes.
In heating function, the heating alarm will flash for
3.5 minutes before the compressor and fan start
up.
If you have fuses , they should be of the time delay
type. Before you install or relocate this unit, be sure
that the amperage rating of the circuit breaker or
time delay fuse does not exceed the amp rating
listed in Table 1.
Table 1.
MODEL
CIRCUIT
RATING OR
TIME DELAY
FUSE
REQUIRED
WALL
RECEPTACLE
AMP VOLT NEMA
NO.
P08S,P10S
15
125
5-15P

INTRODUCTION
Congratulations on your purchase and welcome to Friedrich!
ZoneAire Compact: PORTABLE AIR CONDITIONER
The Air Conditioner has been designed and manufactured to the highest standards of modern
engineering.
Our product not only provides you a remote control to help user operate all the functions easily and
conveniently but also includes the following benefits:
•3-IN-1 SYSTEM: Offers cooling, dehumidification bonus heat for year-round conditioning
and comfort.
•Innovative design: One side offers cooling, simply turn the unit around and apply the exclusive
“heat clip“ for bonus heat option.
•Super portability with built in hose storage compartment underneath unit.
•Dual, easy-access antimicrobial nylon filters
•4-Speed fan with “Auto” setting for ultimate comfort
•24-hour timer for both cooling and dehumidification
•Unique Sleep Control function – Increases temperature 2 degrees every 4 hours
•LCD remote control
•Moves easily from room to room on easy glide castors.
3
and

UNPACKING INSTRUCTIONS & CONTENTS
UNPACKING INSTRUCTIONS
1. Place the unit in the correct upright position before unpacking.
2. Cut the two packing straps.
3. Slide the carton in an upward motion and it will release from the base.
4. Grip the carry handles located on either sides of the unit and carefully lift until it slides out of
the foam base.
5. Lift and lean the unit slightly to take out exhaust hose from unit’s bottom as picture.
6. Install the exhaust hose on the unit before operating the unit.
CONTENTS
1. Air conditioner unit
2. Exhaust Hose
3. Remote control
4. Batteries
5. Window Kit
6. Heat Clip Connector
4
Exhaust Hose
Heat Clip
Window Kit

PARTS
1. Control panel
2. Remote control receiver
3. Hot air-outlet
4. Evaporator’s filter
5. Cool air-inlet
6. Air-outlet’s joint part
7. Cool air-outlet
8. Condenser’ s filter
9. Hot air-inlet
10. Drain hole
5

DISPLAY FUNCTIONS
KEY
Press to turn unit "ON" or "OFF".
2. MODE
Press this key to select cooling, heating, or dehumidifying.
3. TEMPERATURE REGULATION KEY (UP)
- During cooling function：This key raises the preset temperature by 1°F each time it is pressed
and the maximum limit is 86°F.
- During heating function：This key raises the preset temperature by 1°F each time it is pressed
and the maximum limit is 77°F.
4. TEMPERATURE REGULATION KEY (DOWN)
-During cooling function：This key lowers the preset temperature by 1°F each time it is pressed
and the minimum limit is 63°F.
- During heating function：This key lowers the preset temperature by 1°F each time it is pressed
and the minimum limit is 59°F.
5. L.E.D. DISPLAY
The display indicates the current setting temperature or the timer setting. When the set
temperature or the timer is adjusted, the new setting is shown then the display returns the
current set temperature.
6
※The display is also used to show error codes should a fault occur, see TROUBLE SHOOTING.
1. ON/OFF
when the unit is not working, hold the function button for 10 seconds to change the temperature
scale /°F.°C

6. FAN SPEED
Press to select either LOW, MEDIUM, HIGH or AUTO fan speed.
If "AUTO" is selected (During cooling function),”HIGH” or "MEDIUM" or “LOW" will be
selected automatically according to the difference between setting temperature and
ambient temperature.
Note: In heating function and dehumidifying function, this key is invalid because the
unit is defined to be high speed in heating mode and low speed in dehumidifying mode.
7. PROGRAMMABLE TIMER
Programmable timer ON/OFF key.
TIMER-ON: The timer-on is used to turn on the unit automatically after the set time is over.
1. Press the "TIMER" key at stand-by status to set the time you desired.
2. Once the set hour has come to an end, the unit will turn on automatically.
3. Press the "POWER" key before the time out; the set time will be canceled and the unit will turn on.
4. You can set the function and fan speed while setting the timer.
TIMER-OFF: The timer-off is used to turn off the unit automatically after the setting time is over.
1. Press the "TIMER" key at operating status to set the time you desired.
2. Once the set hour has come to an end, the unit will turn off automatically.
3. Press the "POWER" key before the time out, the set time will be canceled and the unit will
turn off.
DISPLAY FUNCTIONS
7

MAINTENANCE AND CLEANING
8. SLEEP CONTROL FUNCTION
1. While in cooling mode, press the SLEEP key to set the temperature. It increases 2°F after an
hour and at most increases 4°F after 2 hours.
2. While in heating mode, press the SLEEP key to set the temperature. It decreases 2°F after
hour and at most decreases 4°F after 2 hours.
3. Press the SLEEP key again to cancel the setting.
9. ALARM
When the water tank is full,"E4" will be displayed on the display panel. To resume operation,
please remove the rubber cap of the drain hose to drain out the water firstly. The E4 warning
will disappear after draining, and then you can restart the unit by pressing the POWER key.
DISPLAY FUNCTIONS
8
In “Sleep” mode, your unit will automatically go into low fan speed allowing the temperature
to slowly drift up (in cooling) or down (in heating). See below:

9
REMOTE CONTROL FUNCTIONS
Instruction for the operating keys:
When a remote control signal is transmitted, a transmission icon on the display flashes once,
indicating the signal has been transmitted.

10
1. Transmission window
2. Liquid crystal display
3. Mode select key:
Select from among the three functions: cooling, heating and dehumidifying. The fast key
function indicates the above operating modes in a cycle when the key is pressed without
being released. However, the transmission icon will not appear until the key is released and
the confirmed mode is transmitted.
4. Setting keys for room temperature:
The set temperature will rise by 1°F when the ▲key is pressed once and the set temperature
will fall by 1°F when the ▼key is pressed once. Both keys have the fast key function and can
make the set temperature rise or fall continuously when the keys are pressed without release.
5. Power key:
When this key is pressed, the memorized modes and other information about temperature,
speed, direction of airflow, sleep, etc., in the remote control will be transmitted to the unit and
it will operate correspondingly. When the key is pressed again, the main unit will stop
immediately.
6. Sleep key
When this key is pressed, the air flow of the unit changes into sleep mode (low speed).
(1) Press “SLEEP” key, set sleep function; press again, and cancel sleep setting.
(2) The temperature will increase 2°F half an hour after setting sleep function, and will
increase at most 4°F every two hours after that.
(3) When the main power supply is cut off, the sleep function setting will be cancelled
automatically.
(4) When you turn off the unit, sleep function setting will be cancelled automatically.
REMOTE CONTROL FUNCTIONS