Fromm P322.0001.01 User manual

1-1
SERVICE MANUAL
BATTERY - POWERED
PLASTIC STRAPPING TOOL
MODEL P322.0001.01
Manual for authorized dealers and service points
P322.0001.01.sen/MAS/© 11.05

1-2
INDEX PAGE
1.1 ACCESSORIES 1-3
1.1.1 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.2 Battery chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.3 Battery tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.4 Charger for car batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1.5 Battery light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.2 TECHNICAL DETAILS 1-4
1.2.1 Electric schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.2.2 Connecting plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.2.3 Strap tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.3 CONVERSION PARTS P322 1-5
1.3.1 Conversion parts: strap width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.3.2 Conversion parts: strap thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.4 PERIODIC MAINTENANCE AND CONTROL 1-6
1.4.1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.4.2 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.4.3 Battery test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.4.4 Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.4.5 Glueing rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.4.6 Lubrication rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1.4.7 Assembly informations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.5 RECOMMENDED SPARE PARTS 1-12
1.6 ACCESSORY TOOLS 1-13
1.7 USE OF ACCESSORY TOOLS 1-14
1.8 ORDERING SPARE PARTS 1-18
1.8.1 Ordering manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
1.8.2 Ordering address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
1.8.3 Finding out of the tool type (item number), the serial number
and the version number: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
1.9 SERVICE ADDRESS 1-19
1.10 CHART OF TYPES 1-19

1-3
1.1 ACCESSORIES
1.1.1 Battery
Use only original Fromm batteries N5.4309 (NiCd) or N5.4316 (NiMH) for the P322 tool.
In case of a damaged battery housing, it can be ordered separately under item no. N5.4318.
1.1.2 Battery chargers
The battery charger must be separately ordered according to the table mentioned below.
Standard charger
Turbo charger
1.1.3 Battery tester
For testing the batteries order battery tester N7.5121.
1.1.4 Charger for car batteries
The charger N5.4407 must be ordered for connection to a car battery with 12 or 24V.
1.1.5 Battery light
For completely discharging of the battery the battery light N5.4313 can be used.
Item-No. Voltage / frequency Admitted for country
N5.4414 220 - 240V / 50 - 60Hz A, B, BG, BIH, BOL, BR, BY, CH, CL, CZ, D, DK, DZ, E, EAS, EST, ET, F,
FIN, GE, GR, H, HK, HR, I, IL, IND, IR, IRQ, IS, JOR, KSA, KWT, L, LAR, LT,
LV, MA, MC, MK, MOC, N, NL, P, PK, PE, PL, PRC, PY, RA, RCH, RI, RL,
RO, ROK, ROU, RP, RUS, S, SK, SLO, SYR, THA, TN, TR, UA, UAE, YU,
YV, (Z), (ZA), (ZW)
N5.4416 220 - 240V / 50 - 60Hz BRN, BRU, CY, EAK, EAT, GB, IRL, M, MAL, OM, SGP, Y
N5.4418 220 - 240V / 50 - 60Hz AUS, NZ
N5.4420 220V / 60Hz ROK
Item-No. Voltage / frequency Admitted for country
N5.4422 220 - 240V / 50 - 60Hz A, B, BG, BIH, BOL, BR, BY, CH, CL, CZ, D, DK, DZ, E, EAS, EST, ET, F,
FIN, GE, GR, H, HK, HR, I, IL, IND, IR, IRQ, IS, JOR, KSA, KWT, L, LAR, LT,
LV, MA, MC, MK, MOC, N, NL, P, PK, PE, PL, PRC, PY, RA, RCH, RI, RL,
RO, ROK, ROU, RP, RUS, S, SK, SLO, SYR, THA, TN, TR, UA, UAE, YU,
YV, (Z), (ZA), (ZW)
N5.4424 120V / 60Hz BR, C, CDN, CO, CR, DOM, EC, GCA, J, JA, KSA, LB, MEX, NIC, PA,
Puerto Rico, RC, RP, USA, YV
N5.4426 110V / 50 - 60Hz GB
N5.4428 220 - 240V / 50 - 60Hz BRN, BRU, CY, EAK, EAT, GB, IRL, M, MAL, OM, SGP, Y
N5.4430 220 - 240V / 50 - 60Hz AUS, NZ

1-4
1.2 TECHNICAL DETAILS
1.2.1 Electric schematic
1.2.2 Connecting plan
1.2.3 Strap tension
The tension force values mentioned in the P322 operation manual (400-2000N) are not achievable with each
strap. They depend on following factors:
• Hardness of the package,
the maximum tension force values are achievable with hard packages.
• Elongation and creep properties of the plastic strap,
the maximum tension force values are achievable by using plastic straps with a low elongation.
• Surface quality of the plastic strap,
the maximum tension force values are achievable with waxed and embossed straps.
• Strap width, strap thickness,
the maximum tension force values are achievable with the thick and the wide straps.
Tensioning motor
Welding motor
red point
red point
red
white black
white
red
1
2
3
4
white
black
red
red point
red pointred

1-5
1.3 CONVERSION PARTS P322
When changing strap thickness or strap width following parts must be exchanged.
1.3.1 Conversion parts: strap width
1.3.2 Conversion parts: strap thickness
10mm 11.1mm 12mm 12.7mm 13mm 15mm 15.5mm 16mm
Guide
pin P30.1156 P30.1158 P30.1156 P30.1157 P30.1158 P30.1159 P30.1160 P30.1161
Guide
pin P30.1162 P30.1164 P30.1162 P30.1163 P30.1164 P30.1165 P30.1166 P30.1167
Guide
case P32.1205 P32.1205 P32.1206 P32.1206 P32.1206 P32.1206 P32.1206 P32.1206
Strap
stop P32.1230 P32.1231 P32.1232 P32.1233 P32.1234 P32.1235 P32.1236 P32.1237
Strap
guide P32.1239 P32.1240 P32.1241 P32.1242 P32.1243 P32.1244 P32.1245 P32.1246
0.4-0.64mm 0.65-1.05mm
Steel insert P32.1201 P32.1202
Tensioning wheel P32.1219 P32.1220
Gripper P32.1222 P32.1225
Gripper P32.1223 P32.1226
Gripper P32.1224 P32.1227
Attention!
When converting tools always change the item number on the type label
Replace following parts:
Type label N43.9108
2 x hammer head bolts N2.4902
Enclose the suitable operation manual with the tool after each
conversion
(see paragraph 1.8.1 Ordering manuals)

1-6
1.4 PERIODIC MAINTENANCE AND CONTROL
(Carry out 12- months cycles doing one shift work. Doing more shift work respectively often.)
1.4.1 Procedure
Before using check tool for following possible faults:
• Visual test of the tool for loose, lost or damaged parts
• Clean all dirty parts of the tool, especially strap abrasion in the tensioning or the welding unit by
using compressed air. (Never use any hard tools like a wire brush or a screw driver for cleaning)
Carry out a test strapping and check following:
• Strap feed and strap tensioning
• Tensioning force adjustment (see operation manual P322)
• Cutting of the upper strap
• Welding time adjustment (see operation manual P322)
• Seal quality (see operation manual P322)
• Function of the LED - display
• Insertion of the strap
Proceed according to paragraph 1.4.2 after a fault appears.
Attention!
Remove battery from tool before each maintenance work.
For exchange of wearing parts see operation Manual P322.
Never use water or solvents for cleaning the tool’s surface.

1-7
1.4.2 Troubleshooting
Ensure before each tool repair that the battery is charged and the tool’s specific strap
is used
SYMPTOM CAUSE REMEDY
Tool doesn’t work at all Battery is empty or defective Charge or replace battery
Contact problems caused by a broken
battery housing N5.4318.
Replace battery housing
Contact problems caused by a
damaged connecting plate P32.1118
or damaged motor housing P32.1418
and P32.1419
Replace connecting plate or motor
housing
Defective busbar P32.1111/14 Replace busbar
Contact problem of the internal wires Check contacts and fix them if required
or change defective parts
Defective circuit board Replace circuit board
Tool doesn’t tension Tensioning wheel is dirty or worn Clean tensioning wheel or replace it,
don’t use any hard objects for this
(see operation manual P322)
P32.1051 is not meshing with
P32.1048, because spring N2.5822 is
defective or parts are dirty
Replace spring N2.5822,
clean dirty parts
Faulty tensioning wheel or tensioning
wheel is assembled reversed
Correct assembling
(see operation manual P322)
Grippers are dirty, worn or faulty
assembled
Replace grippers, clean them or
assemble correct,
don’t use any hard objects for this
(see operation manual P322)
Gearing parts from the tensioning gear
are defective
Loose pinion on P32.1044
Loose pinion on tensioning motor
Check tensioning gear and replace
defect parts
Defective tensioning motor Replace tensioning motor
Defective circuit board Replace circuit board
Micro switch N5.2322 for tensioning
motor is defective
Replace micro switch
Contact problem of the internal wires Check contacts and fix them if required
or change defective parts
Defective gear bearings Replace bearings
Defective tensioning body Replace tensioning body
Needle free wheeling assembled
reversed
Correct assembling

1-8
Tensioning wheel turns
back immediately after the
tensioning cycle
Shaft P32.1014 in lever P32.1051 is
loose
Check parts and replace as required
Defective needle free wheeling
N3.4509
Tool doesn’t weld Welding gripper is dirty or worn Replace or clean welding gripper,
don’t use any hard objects for this
(see operation manual P322)
Welding stop gripper P32.1203 is dirty
or worn
Replace or clean welding stop gripper,
don’t use any hard objects for this
(see operation manual P322)
Damaged housing parts Replace housing parts
Defective circuit board Replace circuit board
Defective welding motor Replace welding motor
Pressure spring N2.5294 defective Replace pressure spring
Loose pinion P32.1119 on
welding motor
Replace pinion
Gearing parts of the welding gear are
defective
Check welding gear and replace
defect parts
Micro switch N5.2322 for welding
motor is defective
Replace micro switch
Defective busbar P32.1108 Replace busbar
Contact problem of the internal wires Check contacts and fix them if required
or change defective parts
Defective gear bearing Replace bearing
Tool badly cuts the strap or
doesn’t cut at all
Cutter is worn or damaged Replace cutter
(see operation manual P322)
Faulty adjustment of the coupler
P32.1250
Check adjustment and readjust if
necessary
(see operation manual P322)
Welding gripper is worn Replace welding gripper
(see operation manual P322)
Welding time too short Change adjustment
(see operation manual P322)
Defective pressure spring N2.5237 Replace pressure spring
Tool switches off after a few
strappings
(Displaying empty battery)
Battery defective or empty Check the battery and change
defective batteries
Gear noise Tensioning or welding gear is worn Check component parts and replace
defect one’s
SYMPTOM CAUSE REMEDY

1-9
1.4.3 Battery test
The battery should be checked while each maintenance by using the battery tester N7.5121.
The use is described in the instruction manual of the battery tester.
• NiCd-Batteries 14,4V / 2,4Ah must be replaced by an capacity less than 1,7 Ah.
• NiMH-Batteries 14,4V / 2,7Ah(3,0Ah) must be replaced by an capacity less than 1,9 Ah(2,1Ah).
1.4.4 Checklist
Carry out some test strappings and check following tool components.
• Insert battery in the tool and check function of the LED-display (see operation manual P322)
• Strap feed and strap tension
• Tension force adjustment (see operation manual P322)
• Cutting of the upper strap
• Welding time adjustment (see operation manual P322)
• Seal quality (see operation manual P322)
• Function of the LED-display (see operation manual P322)
• Inserting of the strap
• Correct type label
1.4.5 Glueing rules
Following parts have to be glued with LOCTITE 603:
Planet shaft P32.1044
with the parallel pins N2.2145.
Tensioning body P32.1254
with the parallel pins N2.2189
Body P32.1402 with
swivel shaft P32.1003
and parallel pins N2.2188
N2.2145
P32.1044
N2.2189
P32.1254
N2.2188
P32.1003
P32.1402

1-10
Additional the screws N1.2112 have to be glued with the
idler step P32.0118 using LOCTITE 222.
Don’t clamp the planet shaft on the pinion while loosening or
tightening the screws N1.2112.
1.4.6 Lubrication rules
All gear parts have to be lubricated with MOLYKOTE BR 2 PLUS grease.
Lubrication interval: While each maintenance or after 12 months at the latest.
All bearing parts of the welding unit have to be cleaned and
lubricated with Klüber Isoflex Alltime SL2 grease while
each maintenance.
Lubrication interval: While each maintenance or after 12
months at the latest.
All other parts have to be greased due to the explosion drawing.
Lubrication interval: While each maintenance
P32.0118
N1.2112
Clamp
here
P32.1029
N3.1702 (6X)
P32.1027
P32.1053
Bearing
welding unit

1-11
1.4.7 Assembly informations
Pay attention to the correct position of the torsional
stops while fitting the welding motor
(see illustration).
Pay attention to the assembling direction
of the needle free wheeling N3.4509.
The sense of rotation is stamped in the
front of the free wheeling
By installing the grippers into the tensioning
body P32.1254 it must be observed the
direction of the teeths.(look at the picture)
Welding motor
Torsional stops
Motor support
N3.4509
P32.1254
Grippers

1-12
1.5 RECOMMENDED SPARE PARTS
Following spare parts are recommended for stock keeping:
Besides should be stocked the wearing parts of the different Types.
Stock only parts from tools that are in sale.
Item-No. Description Pieces per tool
N1.1305 Screw 2
N1.1904 Screw 5
N1.1909 Flat head screw 2
N1.1929 Screw 1
N1.1934 Flat head screw 6
N1.6503 Safety washer 6
N1.6504 Safety washer 13
N1.6505 Safety washer 3
N1.7207 PT-screw 4
N1.7208 PT-screw 4
N2.1118 Security ring 1
N2.1121 Security ring 5
N2.1606 Spring ring 1
N2.1801 Tensioning ring 1
N3.1702 Ball 6
N5.2322 Micro switch 2
N5.4318 Housing 1
P32.0107 Welding motor 1
P32.0108 Tensioning motor 1
P32.1418 Motor housing 1
P32.0142 Lever 1
P32.1401 Body 1
P32.1419 Motor housing 1
P32.1118 Connecting plate 1
P32.1421 Motor cover 1
P32.1413 Circuit board 1
P32.1238 End cover 1

1-13
1.6 ACCESSORY TOOLS
* a) These tools are also included in the P320 tool set.
b) These tools are also included in the P321 tool set.
c) These tools are also included in the P323 tool set.
d) These tools are also included in the P355 tool set.
e) These tools are also included in the P356 tool set.
Item
number
Description
N71.3235 *a,b,c,d,e Press in and press out arbor for N3.4509/P32.1016
N71.3236 *a,b,c Press in and press out pressure pad for N3.4509/P32.1016
N71.3237 *a,b,c,d,e Press in and press out arbor for N3.1159/P32.1037
N71.3238 *a,b,c,d,e Press in and press out pressure pad for N3.1159/P32.1037
N71.3239 *a,b,c,d,e Press in arbor for N3.2347/P32.1024
N71.3240 *a,b,c,d,e Press out arbor for N3.2347/P32.1024
N71.3241 *a,b,c,d,e Press in and press out pressure pad for N3.2347/P32.1024
N71.3242 *a,d Press in and press out arbor for N3.2346/P32.1238
N71.3243 *a,b,c,d,e Press in arbor for N3.1134, P32.1023/P32.1022
N71.3244 *a,b,c,d,e Press out arbor for N3.1134, P32.1023/P32.1022; N5.1129/P32.1123
N71.3245 *a,b,c,d,e Pressure pad for N3.1134, P32.1023/P32.1022; N3.2346/P32.1238
N71.3246 *a,d Press in and press out arbor for N3.1157/P32.1044
N71.3247 *a,d,e Press in and press out pressure pad for N3.1157/P32.1044
N71.3248 *a,b,c,d,e Press in arbor for N3.3172/P32.1254
N71.3249 *a,d Press in and press out pressure pad for N3.3172/P32.1254
N71.3250 *a,d,e Press in and press out arbor N3.3172/P32.1401; N3.3172/P32.1254
N71.3253 *a,b,c,d Press in and press out arbor for P32.1119,N3.1158,P32.1120/N5.1129
N71.3255 *a,b,c Distance sleeve for N3.1158,P32.1120,P32.1119/N5.1129;P32.1123/N5.1129
N71.3256 *a,b,c Press in and press out pressure pad for N3.1158,P32.1120,P32.1119/N5.1129
N71.3257 *a,b,c Press out pressure pad for P32.1119/N5.1129; P32.1123/N5.1129
N71.3258 *a,b,c Press in arbor for P32.1123/N5.1129
N71.3259 *a,b,c Press in and press out pressure pad for P32.1123/N5.1129
N71.3260 *a,b,c Press out arbor for N3.1158,P32.1120,P32.1119/N5.1129
N71.3261 *a,b,c Distance sleeve for N3.1158,P32.1120, P32.1119/N5.1129

1-14
1.7 USE OF ACCESSORY TOOLS
Accessory tools should only be used with the suitable arbor press
N7.5108 to prevent a jam of the parts have to be pressed in.
Additional a retainer (N7.3215) is necessary.
Part Disassembly Assembly
N3.1157/
P32.1044
N3.1159/
P32.1037
N7.5108
N7.3215
N71.3246
N71.3247
N3.1157
P32.1044
N71.3237
N71.3238
N3.1159
P32.1037

1-15
N3.2346/
P32.1238
N3.2347/
P32.1024
N3.3172/
P32.1401
Part Disassembly Assembly
N71.3242
N71.3245
N3.2346
P32.1238
N71.3240
N71.3241
N71.3239
P32.1024
N3.2347
N71.3250
N3.3172
P32.1401

1-16
N3.3172/
P32.1254
N3.4509/
P32.1016
N5.1129/
P32.1119/
N3.1158/
P32.1120
Part Disassembly Assembly
N71.3250
N71.3249
N71.3248
N3.3172
P32.1254
N71.3235
N71.3236
N3.4509*
P32.1016
*Pay attention to the
assembling direction
see assembly informations
N71.3260
N71.3256
N71.3261
N71.3257
N71.3253
P32.1119
N3.1158
P32.1120
N5.1129
N71.3255
N71.3253

1-17
N5.1129/
P32.1123
P32.1023/
N3.1134/
P32.1022
Part Disassembly Assembly
N71.3244
N71.3259
N71.3255
N71.3257
N71.3258
P32.1123
N5.1129
N71.3244
N71.3245
N71.3243
P32.1022
N3.1134
P32.1023

1-18
1.8 ORDERING SPARE PARTS
On principle spare part numbers should be taken from the drawings or spare parts lists. Check if the version
number of the tool and the spare parts list are the same.
Type dependent spare parts should be ordered as follows:
Ordering example
Ordering a tensioning wheel:
• Take item numbers of the tensioning wheel from drawing (P32.1219/20)
• Find out the tool type in which the tensioning wheel should be assembled (e.g. 43.2161)
• Find out the item number of the needed tensioning wheel by using the type dependent spare
parts lists (for type 43.2161 it is tensioning wheel P32.1219).
Order as follows if 10 tensioning wheels are needed:
P32.1219 Tensioning wheel 10 pcs.
1.8.1 Ordering manuals
When converting tools make sure that the used manual has still validity.
If tools change their item number because of the conversion (see chart of types) the adequate manual must
be ordered as follows.
Ordering example:
Tool item number: 43.2161
Version number: 01
Language of the manual: de
The manual order for this tool must look as follows:
43216101.de
If the manual is needed in another language replace the shorthand expression
"de" (see table).
1.8.2 Ordering address
Spare parts and manuals can be ordered at:
Fromm Holding AG Tel.: [phone]
Hinterbergstrasse 26 Fax: [phone]
CH-6330 Cham e-mail: [e-mail]
Switzerland
1.8.3 Finding out of the tool type (item number), the serial number and the version
number:
Type label P322
de German
en English
fr French
it Italian
nl Dutch
po Portuguese
se Swedish
fin Finnish
sp Spanish
ru Russian
cz Czech
43.2161
0100284
{
Item number
Serial number
Version number

1-19
1.9 SERVICE ADDRESS
You will get further assistance and information at:
Post address Physical address:
Fromm System GmbH Fromm System GmbH
Technical customer support Technical customer support
Postfach 12 46 Neulandstr. 10
D-77843 Achern D-77855 Achern
Germany Germany
Phone: [phone] / 62 94-22
Fax: [phone] / 62 94-11
e-mail: [e-mail]
1.10CHART OF TYPES
Item no. Model Strap width Strap thickness
43.2101 P322/10/0.40-0.64 10.0 mm / 3/8" 0.4 - 0.64 mm / .016 - .025"
43.2102 P322/10/0.65-1.05 10.0 mm / 3/8" 0.65 - 1.05 mm / .026 - .041"
43.2111 P322/11.1/0.40-0.64 11.1 mm / 7/16" 0.4 - 0.64 mm / .016 - .025"
43.2112 P322/11.1/0.65-1.05 11.1 mm / 7/16" 0.65 - 1.05 mm / .026 - .041"
43.2121 P322/12/0.40-0.64 12.0 mm 0.4 - 0.64 mm / .016 - .025"
43.2122 P322/12/0.65-1.05 12.0 mm 0.65 - 1.05 mm / .026 - .041"
43.2123 P322/12.7/0.40-0.64 12.7 mm / 1/2" 0.4 - 0.64 mm / .016 - .025"
43.2124 P322/12.7/0.65-1.05 12.7 mm / 1/2" 0.65 - 1.05 mm / .026 - .041"
43.2131 P322/13/0.40-0.64 13.0 mm 0.4 - 0.64 mm / .016 - .025"
43.2132 P322/13/0.65-1.05 13.0 mm 0.65 - 1.05 mm / .026 - .041"
43.2151 P322/15/0.40-0.64 15.0 mm 0.4 - 0.64 mm / .016 - .025"
43.2152 P322/15/0.65-1.05 15.0 mm 0.65 - 1.05 mm / .026 - .041"
43.2153 P322/15.5/0.40-0.64 15.5 mm 0.4 - 0.64 mm / .016 - .025"
43.2154 P322/15.5/0.65-1.05 15.5 mm 0.65 - 1.05 mm / .026 - .041"
43.2161 P322/16/0.40-0.64 16.0 mm / 5/8" 0.4 - 0.64 mm / .016 - .025"
43.2162 P322/16/0.65-1.05 16.0 mm / 5/8" 0.65 - 1.05 mm / .026 - .041"

1-20