Fromm P330 User manual

OPERATION MANUAL / SPARE PARTS LIST
BATTERY - POWERED
PLASTIC STRAPPING TOOL
MODEL P330
43.0266.01
CE Declaration of conformity
We declare that the machine P330
is in conformity with the following standard or
standardised documents:
98/37/EC (until 28.12. 2009),
2006/42/EC (from 29.12. 2009 on),
2004/108/EC
Technical file at:
FROMM System GmbH
D-77855 Achern
27.08.2008
R.Fromm
Director
FROMM Holding AG
Hinterbergstrasse 26
CH - 6330 Cham
43026601.en/MAS/© 05.09 Original instructions
For Parts & Service 1-877-862-6699

2
INDEX PAGE
1 GENERAL SAFETY RULES 3
2 SAFETY RULES FOR STRAPPING TOOLS 5
3 TECHNICAL DATA 6
4 ACCESSORIES 7
4.1 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 Battery - chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.3 Wearing plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.4 Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.5 Turning button kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 OPERATING ELEMENTS 10
6OPERATION 10
6.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.2 Displaying of the status of the battery charge . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.3 Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.4 Feeding the strap around the package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.5 Inserting the strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.6 Tensioning the strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.7 Sealing of the joint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.8 Removing the tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.9 Seal - Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7 CHART OF TYPES 14
8 ELECTRIC SCHEMATIC 14
9 EXCHANGE OF WEARING PARTS 15
9.1 Exchange of tensioning wheel and grippers . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9.2 Exchange of cutter, welding stop gripper and welding gripper . . . . . . . . . . . . 16
9.3 Adjustment of the coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10 SERVICE 17
11 CLEANING 17
12 DISPOSAL 18
13 WARRANTY CONDITIONS AND LIABILITY 18
14 APPROPRIATE USE 18
15 SPARE PARTS LIST 43.0266.01 23
www.traditionaltool.com
For Parts & Service 1-877-862-6699

3
P330mane.fm
1 GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock,
fire and/ or serious injury. The term "power tool" in all of the warnings listed below refers to your mains
operated (corded) power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1.1 Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
1.2 Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will
reduce the risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of electric shock.
1.3 Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal
injuries.
c) Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying
power tools with your finger on the switch or plugging in power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of these devices can reduce dust related hazards.
www.traditionaltool.com
For Parts & Service 1-877-862-6699

4P330mane.fm
1.4 Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the operation of the power tool. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and
in the manner intended for the particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
1.5 Battery tool use and care
a) Ensure the switch is in the off position before inserting the battery pack. Inserting the battery
pack into power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when used with another battery pack.
c) Use power tools only with specifically designated battery packs. Use of any other battery packs
may create a risk of injury and fire.
d) When the battery pack is not in use, keep it away from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal objects that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
e) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
1.6 Service
a) Have your power tool repaired only by qualified personnel using original spare parts. This will
ensure that the safety of the power tool is maintained.
www.traditionaltool.com
For Parts & Service 1-877-862-6699

5
P330mane.fm
2 SAFETY RULES FOR STRAPPING TOOLS
2.1 Joints
You are fully responsible to review the joints made by your tool. Become familiar with the seal
control and seal adjustment described in this operation manual.
Misformed joints may not secure the load and could cause serious injury. Never handle or ship any load
with improperly formed joints.
2.2 Dispensing strap
Only dispense strap from a dispenser specifically designed for strap.
Tuck strap end back into dispenser when not in use.
2.3 Strap warnings
Never use strap as a means of pulling or lifting loads. Failure to follow these warnings can result in
severe personal injury.
2.4 Strap breakage hazard
Improper operation of the tool, excessive tensioning, using strap not recommended for this tool or sharp
corners on the load can result in a sudden loss of strap tension or in strap breakage during tensioning,
which could result in the following:
A sudden loss of balance causing you to fall.
Both tool and strap flying violently towards your face.
Note as follows:
If the load corners are sharp, use edge protectors.
Place the strap correctly around a properly positioned load.
Positioning yourself in-line with the strap, during tensioning and sealing, can result in severe
personal injury from flying strap or tool. When tensioning or sealing, position yourself to one
side of the strap and keep all bystanders away.
Use the correct strap quality, strap width, strap gauge and strap tensile strength
recommended in this manual for your tool. Using strap not recommended for this tool can result in
strap breakage during tensioning.
2.5 Cutting tensioned strap
When cutting strapping, use the proper strapping cutter and keep other personnel and yourself at a
safe distance from the strap. Always stand to side of the strap, away from the direction the loosened
strap end will fly. Use only cutters designed for strap and never hammers, pliers, hacksaws, axes, etc.
2.6 Environment protection
Do not dispose of used batteries in the household refuse, water or by burning them.
FROMM distributors offer an environment friendly battery disposal service.
www.traditionaltool.com
For Parts & Service 1-877-862-6699

6P330mane.fm
3 TECHNICAL DATA
Description of the tool
The tool model P330 has been designed to strap packages with plastic strapping. The plastic strapping is fed
around the package manually or in combination with a strap feeder. The straps are inserted in the tool,
automatically tensioned, sealed by friction welding and separated.
Tool size with battery
Length: 395 mm / 14“
Width: 137 mm / 5“
Height: 143 mm / 5“
Weight: 5,7 kg / 12,57 lbs
Noise information
The A-weighted equivalent continuous sound level at the work place of the machine operator is
typical 84 dB (A). The sound power level is 92 dB (A).
This value was determined according to DIN EN 60745-1 (12.2003).
Deviation K: 2.5 dB
Wear ear protection!
Vibration information
The weighted effective value of the acceleration typically amounts to less than 2.5 m/s2.
This value was determined according to DIN EN 60745-1 (12.2003).
Deviation K: 0,6 m/s2
Strap material
Strap qualities: PET (Polyester) and PP (Polypropylene) plain or embossed.
Use only plastic straps recommended by your sales shop (name and address
on the rear of the operation manual).
Strap dimensions: 19.0 - 25.0 mm / 3/4 - 1" x 0,40 - 1,53 mm / .016 - .060" (see chart of types).
Use only plastic straps with the correct strap dimensions for your tool.
Strap tension
Tensioning force*: Adjustable from 1200 - max. 6000 N / 270 - max. 1350 lbs.
Tensioning speed*: approx. 70 - 87 mm/s / 2,76 - 3,43 inch/sec.
Joint strength*: approx. 75% of the tensile strength of the plastic strap.
* The value depends on the strap quality.
Working temperature
The ambient temperature should be between -10° and 45° C (14° and 113°F).
The best performance is achieved between 15° and 20°C (59° and 68°F).
www.traditionaltool.com
For Parts & Service 1-877-862-6699

7
P330mane.fm
4 ACCESSORIES
Use only parts and accessories mentioned in the operating instruction. Using other
parts or accessories can cause injuries to you and other persons.
4.1 Battery
The battery is not automatically supplied with the tool and has to be ordered
separately under the following item number:
4.2 Battery - chargers
The charger must be ordered separately according to below shown table.
Item-No. Battery Voltage Capacity
N5.4326 Li-Ion 28 VDC 3,0 Ah
Item-No. Voltage / frequency Admitted for country
N5.4435 220 - 240V / 50 - 60Hz A, B, BG, BIH, BOL, BR, BY, CH, CL, CZ, D, DK, DZ, E, EAS, EST, ET, F,
FIN, GE, GR, H, HK, HR, I, IL, IND, IR, IRQ, IS, JOR, KSA, KWT, L, LAR, LT,
LV, MA, MC, MK, MOC, N, NL, P, PK, PE, PL, PRC, PY, RA, RCH, RI, RL,
RO, ROK, ROU, RP, RUS, S, SK, SLO, SYR, THA, TN, TR, UA, UAE, YU,
YV, (Z), (ZA), (ZW)
N5.4437 120V / 50 - 60Hz BR, C, CDN, CO, CR, DOM, EC, GCA, J, JA, KSA, LB, MEX, NIC, PA,
Puerto Rico, RC, RP, USA, YV
N5.4439 220 - 240V / 50 - 60Hz BRN, BRU, CY, EAK, EAT, GB, IRL, M, MAL, OM, SGP, Y
N5.4441 220 - 240V / 50 - 60Hz AUS, NZ
www.traditionaltool.com
For Parts & Service 1-877-862-6699

8P330mane.fm
4.3 Wearing plate
In order to protect the P330 when using on packages
with hard and rough surface, the tool can be
equipped with a wearing plate and a disk for level
compensation.
The complete wearing plate together with disk and
fastening screws can be ordered under item number
P33.0121.
If the complete bottom side of the tool has to be
protected, the plate P33.0122 must be used.
4.4 Suspension
When working stationary the P330 can be suspended at a spring loaded balancer by using a suspension
bracket.
For working in normal position a stiff suspension bracket with screws and washers can be ordered under item
number P32.0112.
P33.0122
N1.2221
N1.2221
P32.2031
P33.1305
P32.2069
N1.5124
P33.1306
P33.0121
P32.0112
N1.6503
N1.1912
P32.1303
www.traditionaltool.com
For Parts & Service 1-877-862-6699

9
P330mane.fm
For working in alternating positions a turn able suspension bracket with screws and washers can be ordered
under item number P33.0120.
4.5 Turning button kit
For a remaining adjustment of tension force and welding time.
After exchanging of the turning buttons the adjustment can only be changed with the allen key (2mm) that
comes with the kit. The kit can be ordered under the item number P32.2061.
P33.0120
N1.5105
N2.5623 c
P35.2073 c
P33.1302
P35.2069 c
cP33.1301
N1.1904
N1.6503
cMobilux EP2
www.traditionaltool.com
For Parts & Service 1-877-862-6699

10 P330mane.fm
5 OPERATING ELEMENTS
6OPERATION
6.1 Installation
Do not expose power tools to rain or wet conditions!
For safety reasons the battery is delivered uncharged.
Charge the battery before working.
See separate operating instruction of the battery charger.
When charging the battery the very first time, we recommend a charging time of at least 12 hours.
Never charge a damaged battery. Replace by a new one immediately.
Do not open batteries and store them only in dry and frost-proof rooms.
The maximum ambient temperature is 50°C.
Keep dry at all times.
Inserting the battery
Insert the battery from top to bottom into the tool
until both unlatching push buttons are engaged.
When inserting the battery the LED - indication
shortly lights green.
Removing the empty battery
If the red LED starts blinking while a tensioning or welding procedure, the capacity of the battery is exhausted.
All electric functions of the tool are locked.
The seal efficiency is insufficient.
Warning! Straps with insufficient seal strength must be removed from the package!
The battery must be recharged.
Push the unlatching push buttons at both sides of the battery.
Push the battery out of the tool in the opposite direction of insertion.
LED - Indication
Green During tensioning the LED
lights green.
Green During welding the LED lights
green.
Yellow Cooling time is running, the
tool must not be removed from
the strap.
Green Cooling time is finished, the
tool can be removed from the
strap.
Red blinking Charge the battery.
Tension button
Sealing lever
Unlatching push button
LED
Handle lever
www.traditionaltool.com
For Parts & Service 1-877-862-6699