Front Runner Pro Water Tank with Strap User manual

WTAN063_REV_A01 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
WTAN063
ENG
1
Pro Water Tank with Strap
/42L -by Front Runner
Thank you for purchasing a Front Runner Pro Water Tank with Strap / 42L.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

WTAN063_REV_A01 2 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
6
4
5
7
1
5
8
4
6
2
3
9
TOOLS NEEDED
13mm
24mm
1 1 X Pro Tank Strap Assembly
2 1 X Side Profile Catch
3 1 X M8 x 20 Button head
4 4 X M8 Nyloc Nut
5 3 X M8 x 16 Hex Bolt
6 3 X M8 Nut Cap
7 1 X 550mm T-Slot Rubber
8 1 X Slat Catch
9 1 X 42L Tank
IN THE BOX
FIGURE 1.1
5mm
Craft Knife
Thread Tape
GET ORGANIZED
1
Torx
T30

WTAN063_REV_A01 3
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
3
2
4
5
7
FIT AND SECURE
2
Cut the T-Slot Rubber (Item 7) into two equal
lengths before inserting it into the slats
T-slot as shown.
2.1
2.2
2.3
Slide the M8 x 16 Hex Bolt (Item 5) into the
3rd slats machined slot as shown.
Choose where you would like to mount your
Pro Water Tank, on your Front Runner Rack.
Slide one M8 Nyloc Nut (Item 4) into the
chosen Combined Slats T-slot.
Loosely fit the Catch (Item 2) using the
M8 Nyloc and a M8 x 20 Button Head Bolt
(Item 3) as shown.
SLII SIDE PROFILE FITMENT
5mm

2
1
4
WTAN063_REV_A01 4
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
FIT AND SECURE
2
If you are fitting the tap apply thread tape to
the thread of the tap.
This will allow the Tap to be aligned to your
chosen position and have a water tight seal.
Sold Seperately
Tap - WTAN059
2.4
2.5
2.6
Open the Strap and place the Pro Water Tank
onto the rack. Close the Strap over the
Water Tank as shown.
Ensure that the Tank and the Strap are
aligned before fully tightening the M8 Nyloc
on the Strap and the M8 x 20
Button Head Bolt on the Catch (Item 2).
Once secured, place a M8 Nut Cap
(Item 6) over the Nyloc Nut.
Loosely fit the Pro Tank Strap (Item 1) to the
rack using the M8 x 16 Hex Bolt From 2.2 and
M8 Nyloc Nut (Item 4) as shown.
24MM
13mm
13mm
SLII SIDE PROFILE FITMENT

3
2
8
4
6
5
5
3
2
8
4
5
WTAN063_REV_A01 5
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
FIT AND SECURE
3
Slide the M8 x 16 Hex Bolt (Item 5) into the
3rd slat as shown.
3.1
3.2
3.3
Choose where you would like to mount your
Pro Water Tank Bracket.
Remove the Self Forming Screws as shown,
lift the slat and slide two M8x20 Hex Bolts in
the bottom T-Slot. Assemble the Bracket as
shown using M8 Nyloc Nut.
Choose where you would like to mount your
Pro Water Tank Bracket.
Slide the M8 x 16 Hex Bolt (Item 5) into the
bottom of the slats machined slot and loosely
assembly the Slat Catch (Item 8) using M8
Nyloc Nuts(Items 4). assemble theSide Profile
Catch onto the Slat Catch using a M8x20
Button Head and M8 Nyloc Nut
(Items 2, 3 & 4).
SLII SLAT FITMENT
SLIM SPORT RACK FITMENT
5mm
Torx
T30
13mm
5mm

7
WTAN063_REV_A01 6
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
FIT AND SECURE
3
Open the Strap and place the Pro Water Tank
onto the rack. Close the Strap over the
Water Tank as shown.
Ensure that the Tank and the Strap are
aligned before fully tightening the M8 Nyloc
on the Strap and the M8 x 20
Button Head Bolt on the Catch (Item 2).
Once secured, place a M8 Nut Cap
(Item 6) over the Nyloc Nut.
3.4
3.5
3.6
Loosely fit the Pro Tank Strap (Item 1) to the
rack using the M8 x 16 Hex Bolt From 3.2 and
M8 Nyloc Nut (Item 4) as shown.
Cut the T-Slot Rubber (Item 7) into two equal
lengths before inserting it into the slats
T-slot as shown.
13MM
13mm
SLII SLAT FITMENT

INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
4
Congratulations! You did it. Take a step back and admire your work!
WTAN063_REV_A01
7
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
FIT AND SECURE (SLIMSPORT RACK)
3
3.7
If you are fitting the tap apply thread tape to
the thread of the tap.
This will allow the Tap to be aligned to your
chosen position and have a water tight seal.
Sold Seperately
Tap - WTAN059
Pro Water Tank / 42L - WTAN062
24MM