Front Runner RRAC018 User manual

RRAC018_REV_A00 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
Thule Rapid FOOT System
Adaptor Plates
RRAC018
ENG
1
IMPORTANT WARNING!
Thank you for purchasing a Front Runner Thule Rapid Foot System Adaptor Plates
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

2 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
7
RRAC018_REV_A00
TOOLS NEEDED
1 4 X Thule Rapid Foot System Adaptor Plates
2 4 X M8 x 16 Button Head Bolt
3 8 X M8 x 20 Hex Bolt
4 12 X M8 Nyloc Nut
5 12 X M8 Flat Washer
6 8 X M8 Nut Cap
IN THE BOX
FIGURE 1.1
5mm
13mm
GET ORGANIZED1
3
1
5
6
2
4

RRAC018_REV_A00 3
4
5
1
2
4
5
1
3
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS
FIT AND SECURE
2
Unlock and remove the Locking Handle of
the Strap-On-Foot. Loosen the M6 Socket
Head Screw using the Allen Key supplied
with the Strap-On-Foot. You will see that
this will loosen the Strap of the Foot.
Remove one end of the Strap. Slide the
Thule Rapid Foot into the Adaptor Plate
channel up to the Button Head Bolt.
(Item 2)
Insert a M8 x 20 Hex Bolt (Item 3) into
each of the required Slats using the
Machined Slots as shown.
Place the Adaptor Plate (Item 1) over the
Hex Bolts and loosely fasten using M8 Flat
Washers and M8 Nyloc Nuts (Items 5 & 4).
The Button Head Bolts must face inward.
The assembly should still be able to slide.
8MM
3MM
2.1
2.2
2.3
Insert and fasten the M8 x 16 Button Head
Bolts (Item 2) to the Adaptor Plates (item 1)
using the M8 Nyloc Nuts and M8 x 16 x 1SS
Flat Washers. (Items 4 & 5)
13MM
13MM
5MM
© COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS

RRAC018_REV_A00 © COPYRIGHT 2017 FRONT RUNNER VEHICLE OUTFITTERS 4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES5
Now's the time to visit your favorite Front Runner Dealer in person or Online.
COMPLETION
3
3.1
Congratulations! You did it. Take a step back and admire your work!
4Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
FIT AND SECURE
2
2.4
13MM
Flip the Rack over so that the Strap-On-Feet
are below the Rack. Place the Rack on your
vehicle so that the Strap-On-Feet are
positioned on the Raised Rails of the
vehicle as shown in 2.4
Wrap the Straps around the Raised Rails
and refit the loose end into the Rapid Foot
as removed in Step 2.3.
Fully tighten the Strap by using the Allen Key
on the Locking Handle.
Before fully tightening the Adaptor Plates,
center the rack on your vehicle.
Finally, make sure that all four of the Adaptor
Plates are fully tightened. Place M8 Nut Caps
(Item 6) over all the Nyloc Nuts.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on: