Front Runner SSLD001 User manual

1
land rover defender 2.4
drawer kit
SSLD001
INSTALL TIME: 45 mins
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR
VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY
INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER
PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE
PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE
INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO
NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A
PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
SSLD001_REV_A00

2
GET ORGANIZED...
Here is what you are looking at:
You will need:
13 mm Flat or Socket Wrench
4 mm Hex Key
4mm & 9mm Drill Bits
Drilling Machine
20mm Hole Punch
Clinch Nut Tool
Familiarize yourself with the parts and then step away from the work area and read through these
instructions from beginning to end. Take a moment as a little prep now may save you a lot of time later.
( A )
Item # Quantity Description
110 M6 Countersunk Cap Screw
2 1 Deck
3 4 M10 Flat Washer
412 M8x19x3 Flat washer
5 4 M6 Clinch Nut
6 4 M6 x 25 Countersunk Cap Screw
7 1 Drawer
SSLD001_REV_A00

3
INSTALLING DRAWER SYSTEM
Now with the Jump Seats removed,
Remove the Deck from the Drawer
System. To do this unscrew the ten M6
Countersunk Cap Screw from the Deck
with a 4mm Hex Key. As shown in the
diagram to the right. Retain the Screws
for reuse later.
( A )
Carefully place the Drawer System into the
vehicle and place the Deck back on to the
Drawer making sure that the Deck fits
between the left and right hand wheel arches.
Position the Drawer underneath the Deck so
that the Holes in the Deck line up with the
Screw Holes in the Drawer. With the holes
lined up, loosely screw two of the Counter
Sunk Cap Screws previously removed in
Step2A into the front two holes. Position the
Drawer System so that the Deck lines up with
the inside edge of the door jam, as indicated
by the arrow in the picture.
( B )
( C )
Remove the Deck again. Take care not to move the
Drawer
To install your Drawer System you will need to remove the Jump Seats form your vehicle first.
SSLD001_REV_A00

4
INSTALLING DRAWER SYSTEM CONT...
Using the drawer as a template, mark out the bottom
four bolt holes with a white marker. For the front two
holes lift the carpet slightly. There is a hole in either
corner of the drawer base. (See picture to the right) For
the rear two, unlatch the Drawer and open it out
partially. It may be easier to mark these two holes by
leaning over the rear seats from the inside of the vehicle.
( D )
Remove the Drawer from the vehicle exposing the marks you have just made.
Drill 4mm pilot holes through the carpet and the floor of the vehicle. Now lift up the Carpet and open up
the Pilot Holes with a 9mm Drill Bit. Punch four holes in the carpet where you have just drilled the Pilot
holes, with a 20mm Hole Punch. Lay the carpet back down and insert the Clinch Nuts (Item 5) into the
holes in the body and crimp firmly.
( E )
( F )
Stack three 19x3mm Fat Washers (Item 4) on top of the Clinch Nuts to compensate for the carpet
thickness. Carefully place the Drawer System on top of the stacked Washers. Fasten the Drawer System in
place with the M6x25 Countersunk Cup Screws and M10 Flat Washers (Item3 &6). Use a 4mm Hex Key to
firmly fasten the four Cap Screws.
Finally fit the Deck with the Ten Countersunk Cap Screws you removed in Step2A.
( G )
Congratulations, you have
completed your installation.
Take a step back and admire
your work. Good Job!
SSLD001_REV_A00