FrontLine FLBED9562LB User manual

m a n u a l
EOS Offset Quadrant

Installation instructions:
Offset Quadrant
Adjustment range: (-25mm / -5mm) x (-30mm / -5mm) x 1900mm
Mounting Preparation
After opening the packaging, read the instructions carefully. Check whether all parts are present and there is no sign of shipping
damage. If you find any problem, please contract your retailer directly.
Necessary tools:
spirit level electric drill crosstip screw driver pencil rubber hammer
knife ruler silicon sealant inner hexagon spanner wrench
Packing list:
2.5mm
5mm
8EQO3
8EQO5
8EQO14
8EQO8
8EQO9
8EQO15 8EQO15
8EQO16
8EQO8
8EQO9
8EQO14
8EQO22
8EQO3
8EQO21
8EQO12
8EQO1
10x
8EQO11
4x
8EQO10
4x
8EQO7
1x
8EQO6
4x
8EQO4
6x
8EQO2
10x
8EQO12
2x
8EQO17
2x
8EQO18
2x 2x
8EQO20
2x
8EQO19

12
1. If the offset quadrant is placed onto a tray, first take a spirit
level to check whether the tray is placed horizontal. In case
the quadrant is installed directly onto the floor, please
proceed with step 2.
2.Put the wall profiles 8EQO3 against the wall, ensuring the distance
between the profile and the wall is correct. Please make sure profile to
be 5mm away from outside edge. Adjust the profile to make sure it is
vertical by using a spirit level. Mark the holes on the wall.
34
3. Drill the holes ( 6mm) according to the marks and
insert the wall plugs 8EQO1 into the holes.
Ø4. Fix the wall profiles 8EQO3 with the St4x30 screws 8EQO2 to the
wall.
8EQO3
8EQO3
8EQO1(8x)
8EQO2(8x)

5
6.1
Flex. 25mm
8EQO20(2x)
8EQO6(2x)
8EQO21
8EQO19(2x)
6
6.2
6.3
5.Insert the fixing glass 8EQO5 and 8EQO22 into the wall profiles. 6. Adjust the position of vertical profile and wall profile to suitable
position and then mount rail profile 8EQO21 by assembling fixing
part 8EQO19 and 8EQO20 on fixing panels. Cover 8EQO6 on the back
of 8EQO20.
8EQO7(2x)
8EQO2(2x)
8EQO6(2x)
7
7.1
8EQO1(2x)
7.Attach the vertical sealer 8EQO8 on the fixing panel 8EQO5. Put
the bottom bracket 8EQO7 on the fixing glass panel and mark the
hole for the bracket. Drill the holes ( 6mm) according to the marks
and insert the wall plugs 8EQO1 into the holes. Fix the bracket
8EQO7 with the St4x30 screws 8EQO2 to the tray. Put the cover
8EQO6 on screw.
Attach the vertical sealer 8EQO8 to fixing panel 8EQO5.
Ø
8EQO11(4x)
8EQO14
8EQO15
8EQO14
8EQO15
8
8. Assemble rollers 8EQO11 on sliding panel 8EQO14. Attach bottom
seal 8EQO15 on the bottom of glass.
8EQO5 8EQO22
6.2
6.3
8EQO8
8EQO8

9
9.1
9.Put the sliding panel on the rail profile.
Adjust the top roller to make sure sliding panel is vertical to the rail
profile. The roller’s washer is eccentric. Please adjust the eccentric
washer to right position and fasten the nut.
10
10.Attach magnetic strip 8EQO12 to sliding panel 8EQO14.
Attached vertical sealer 8EQO9 to the other side of sliding
panel.
11
8EQO10(4x)
8EQO12(2x)
11.1
11.2
11.Assemble the fixing part 8EQO10 on sliding panel below rail profile. 8EQO10 is eccentric. Adjust the distance between rail profile
and 8EQO10 to be 0.5mm.
Mount handle 8EQO12 on the sliding panel.
8EQO9
8EQO12
8EQO9

8EQO4(6x)
14
13
12
13.2
13.1
8EQO17(2x)
8EQO18(2x)
12.5
12.1
12.2
12.3
12.4
12. Put silicon glue on the back of bottom aluminum strip 8EQO16.
Put it on the tray edge between brackets 8EQO7.
Put the profile cover 8EQO18 on the vertical profile and put profile
cover 8EQO17 on the wall profile.
13. Drill the holes (6mm) on vertical profile into wall profile
8EQO3 and door profile. Use rubber washers and screws 8EQO4
to fix them in place. Press the screw caps over screws.
14. Finally, at all points connects to the wall, shower tray/floor andthe profiles, use silicone sealant only on the outside of the shower
enclosure.
This cabin can be installed handed. Above installation is based on right hand version. For left hand version, please follow up the step
in mirror direction.
For information and support phone: [phone]
8EQO16
8EQO4(6x)