Frymaster FilterQuick Operating and safety instructions

FilterQuick Controller Field Replacement for FilterQuick Models
1
The FilterQuick service controller ships with the latest software
installed and with an SD card for updating other FilterQuick
controllers on the fryer bank. There are important assessments that
have to be made to ensure the service controller is properly set up for
the fryer it is being installed on and that it’s in sync with the settings of the mounted controllers.
Ensure the fryer to get the controller is a FilterQuick model. FilterQuick fryer controllers are
linked by an orange CAN network cable and share data.
Is the fryer connected to a bulk oil or waste system?
The controller must be set to match the setup of the fryer and the other FilterQuick controllers on the
fryer. The service FilterQuick controller’s default setup is: Fuel: Gas; Type: GL30 Full; Fresh Oil:
JIB; Waste Oil: None. Controllers in a CAN bus-linked system with mismatched settings will exhibit
operational errors.
Follow the steps in Section 1.4 in the provided manual to assess the settings of the leftmost
controller on a FilterQuick fryer. Make a note of each setting , they will have to be transferred to
the service controller.
Follow the instructions on the following page to replace a FilterQuick controller and start the setup for
a FilterQuick controller on a FilterQuick fryer.
CONTROLLER
REPLACEMENT IS NOT
PLUG AND PLAY
Accurate setup is essential
07/2015
*8197265*

FilterQuick Controller Field Replacement for FilterQuick Models
2
Replacing the Controller
1. Follow the steps in Section 1.4 in the provided manual to record the settings of the replacement
controller on the FilterQuick fryer. Make a note of all settings (include all 20 buttons in
Product Set-up and Vat Set-Up to include System, Time/Date, DST and Filter). They will
have to be transferred to the new service controller.
2. Disconnect the fryer from the electrical power supply.
3. Open the control panel by removing the screws on the bottom of the bezel. Carefully lower the
bezel.
4. Remove the two screws from the upper corners of the controller. The controller is hinged at the
bottom and will swing open from the top.
5. Unplug the wiring harnesses from the connectors on the back of the controller, marking their
position for reassembly. Disconnect the ground wires from the terminals. Remove the controller,
lifting it from the hinged slots.
6. Install the new replacement controller in the far most left position to
setup up the controller.
7. Attach the ground wires and harnesses removed in step 5.
8. Rotate the controller up and install one screw to position it for the
setup sequence.
9. Follow the instructions below to setup the controller to match the settings recorded earlier from the
fryer bank’s leftmost controller.
Setup: FilterQuick Fryers
Left Display Right Display Action
OFF OFF
Press until the controller scrolls Info Mode, changing to Main and then PRODUCT
SETUP.
Product
Setup
Blank Press to scroll to Vat Setup. Press .
Vat setup Enter
code
Enter 1656
system Press .
Language English Press  to scroll to another language. Press .
2nd
Language
Spanish Press  to scroll to another language. Press .
Locale Non-ce Press  to change locale. Press .
Energy gas Press  to change to ELEC if necessary. Press .
Type Gl30 full
Press  to scroll to GL30 Split (GL…OSP designations are for European usage.) if
necessary. Press .
System
volume
5 Press  to change to setting recorded from fryer controller. Press .
Temper
format
F Press  to change to setting recorded from fryer controller. Press .
Exit melt
TMPR
180F Press  to change to setting recorded from fryer controller. Press .
Ground Wire Terminal
20-Pin Connecto
r
Ground Wire Terminal
Communication Wires Locator Wire
NOTE:Therightmostcontrollerwillalsohave
anend‐of‐lineresistor.Itmustbetransferred
toanewcontrolleroccupyingtherightmost
position.
Drain Switch
and LED

FilterQuick Controller Field Replacement for FilterQuick Models
3
Left Display Right Display Action
Cool mode
TMPR
250F Press  to change to setting recorded from fryer controller. Press .
Cool mode
default
0 Press  to change to setting recorded from fryer controller. Press .
Fresh oil JIB Press  to change to setting recorded from fryer controller. Press .
Waste None Press  to change to setting recorded from fryer controller. Press .
Recovery
alarm
Disabled Press  to change to setting recorded from fryer controller. Press .
Basket lift Disabled Press  to change to setting recorded from fryer controller. Press .
Hold time Auto Press  to change to setting recorded from fryer controller. Press .
Exit Exit
Press .
10. If moving the controller to another location, lower controller and remove locator pin jumper
harness.
11. Reinstall the original left most controller and install the new replacement controller in the desired
position.
12. Install locator pin from fryer control box and end-of-line resistor (if controller is going into
rightmost position.)
13. Attach orange CAN bus wires.
14. Rotate controller up and secure on control box.
15. Move to the leftmost controller and install the software, following the provided software update
instructions.
16. Return to these instructions after the software update.
17. Perform the setup sequence from Section 1.4 in the manual on the leftmost controller, which
ensures all settings in the master controller (the leftmost position) are shared with all controllers in
the bank. The steps for Time and Date and Daylight Savings Time must be followed as well.
18. Determine if the restaurant assigns filter counts and cool mode time to their menu items and relies
on the controller to prompt for filtering after a programmed cook count. The parameters for filter
counts and cool mode time, if used, must also be programmed into the replacement controller.
Note: All controllers in a bank of fryers may not all be set to the same filter count or cool mode
time.
19. If a chicken restaurant, determine if segmented cooking cycles are used for bone-in chicken.
20. Follow the instructions in Sections 1.6, 1.7 and 1.8 to program the controller for the restaurant’s
menu.
21. When programming the replacement controller is complete and the controllers are in the correct
location, the entire fryer bank must be power cycled to ensure all parameters (including date and
time) transfer to all controllers.