Fuel KS 300 User manual

Footplate Connector
1pc
Front Base Frame
1pc
Base Frame
1pc
Seat Support Frame
1pc
Front Support Frame
1pc
Leg Extension Frame
1pc
Right Base Frame
1pc
Upper Cross Beam
1pc
Weight Guide Tube
2pcs
Left Connect Frame
1pc
Right Connect Frame
1pc
Seat Frame
1pc
Press Arm
1pc
Arm Bracket
1pc
Footplate
1pc
Footplate Fixed Tube
1pc
Arm Support Frame
1pc
Arm
2pcs
Selector Shaft
1pc
Lower Bar
1pc
Lat Bar
1pc
Support Frame
1pc
Rotational Pulley Block
2pcs
Backrest Frame
1pc
Rear Upright Frame
1pc
Top Fixing Bracket
1pc
Bottom Cross Connector
1pc
Upper Fixed Tube
1pc
Lower Fixed Tube
1pc
Pulley Cover
1pc
Single Pulley Block
1pc
Adjustable Pulley Block
2pcs
Pulley Block
4pcs
Cable U
3pcs
Safety Cover
2pcs
Steel Bushing(
￠ 16X ￠ 11)
4pcs
Steel Bushing( ￠ 10X ￠ 7)
2pcs
Seat Cushion
1pc
Backrest Cushion
1pc
Leg Foam
Roller
4pcs
Top Weight Plate
1pc
Weight Plate
15pcs
Head Cushion
1pc
Upper Cable
1pc
39 40
36 37 38
24 25
26
34
45
3
2
1
78
6910
11 1514 13
12
17
16 19
18
28 29 30
27
33 35
31 32
45
44
41 42 43
22
21 23
20
Foam Roller Bracket
1pc

Select Shaft End Cap
1pc
Ankle Strap
1pc
AB Strap
1pc
Strap Handle
2pcs
Pothook
7pcs
Selector Shaft Bushing
1pc
Selector Shaft Pin
1pc
Plastic Washer
1pc
Chain(short)
1pc
Chain(long)
1pc
Pulley
30pcs
Weight Selector Pin
1pc
Quick Knob(short)
2pcs
Oil Bushing
12pcs
Handle
3pcs
Spring
3pcs
Insert Pin (long)
2pcs
Quick Knob(long)
1pc
Rubber
Ring
4pcs
Axle Collar
2pcs
Arm Cable
1pc
Lower Cable
1pc
48
47
46 50
54 55
53
52
51
57 58
56 59 60
61 65
64
63
62
67
66 68 69 70
71 72 73 74
49
75
79
84
89 9088
8786
81
76 77 78
82 83 85
80
Connection Cable
1pc
Insert Pin (short)
1pc
Buffer with Bolt
1pc
Rectangular Buffer
2pcs
Ring
2pcs
Roller
2pcs
￠32X125mm Handle Foam
6pcs
Plastic Bushing (￠50X￠11)
2pcs
Plastic Bushing (￠45X￠26)
2pcs
50mm Square End Cap
7pcs
Pulley Bushing (short)
2pcs
Pulley Bushing (long)
10pcs
Washer (￠45X￠26)
2pcs
25mm Round End Cap
4pcs
50X100mm Square End
Plug 1pc
50X70mm Square End
Plug 2pcs
25X50mm Square End
Plug 6pcs
50mm Square End Plug
6pcs
45mm Square End Plug
3pcs
25mm Square End Plug
2pcs
41.6X70mm Ellipse End Plug
2pcs
￠30X125mm Handle
Foam 2pcs
￠30X425mm Handle
Foam 2pcs

129
Hole Plug
22pcs
126
Handle Tube
2pcs
M10X20mm Hex Bolt
2pcs
127 128
Arc Washer M10
2pcs
30mm Round End Plug
4pcs
25mm Round End Plug
2pcs
Buffer
1pc
Buffer(small)
1pc
91 92 93 94 95
96
101
106
111
116
121
97 98 99 100
102
107
112
117
122
103
108
113
118
123
104
109
114
119
124
105
110
115
120
125
32mm Round End Plug
4pcs
Shaft
2pcs
M10X235mm Hex Bolt
2pcs
Carriage Bolt M10X60mm
6pcs
M10X125mm Hex Bolt
1pc
M10X90mm Hex Bolt
4pcs
M10X85mm Hex Bolt
1pc
M10X75mm Hex Bolt
5pcs
M10X70mm Hex Bolt
13pcs
M10X65mm Hex Bolt
4pcs
M10X50mm Hex Bolt
6pcs
M10X45mm Hex Bolt
13pcs
M10X35mm Hex Bolt
5pcs
M8X40mm Hex Bolt
2pcs
M10X25mm Bolt
4pcs
M8X16mm Hex Bolt
22pcs
M6X45mm Hex Bolt
2pcs
M16 Washer
4pcs
M10 Washer
111pcs
M8 Washer
22pcs
M16 Nylon Nut
4pcs
M10 Nylon Nut
59pcs
Screw M6X6mm
4pcs
Screw M5X5mm
2pcs
Screw M5X10mm
4pcs
M6 Washer
4pcs
Washer ( ￠ 28X ￠ 10)
2pcs
M6 Nylon Nut
2pcs
M8X85mm Hex Bolt
2pcs
M10X65mm Bolt
1pc
M10 Nut
2pcs

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
19
20
21
22
23
24
25
26
27
27
28
29
30
31
31
32
36
36
36
38
38
39
40
41
42
42
42
42
43
44
49
49
50
50
50
49 51
51
52
53
54
55
55
55
55
55
55
56
57
58
60
61
61
62
63
63
63
63
63
63
63
63
63
64
65
66
66
67
67
68
69
70
70
71
71
72
73
73
73
73
74
74
75
75
76
76
77
77
78
78
78
78
78 78
78
79
80
80
81
81
84
85
85
86
86
86
86
86
86
88
88
88
89
89
90
90
91
91
91
91
92
92
92
92
93
93
94
95
87
87
87
87
87
96
96
99
99
101 101
101
101
102
102
102
102
102
103
103
104
104
104
107
107
107
108 108
109
110
111
111
112
112
112
112
112
112
112
112
112
112
112
112
112
112
112
112
113
113
114
114
115
115
116
117
117
117
117
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
118
119
120
120
120
120
120 120
120
120
120
120
120
120
120
120
120
120
121 121
121
121
122
122
122
122
123
123
123
123
123
123
123
123
123
123
123 123
123
123
123
123
123
123
123 118
123
123
123
118
118
124
125
125
126
126
126
126
126
126
75
107
129
118
128
127
75
118
128
107
129
127

104
104
104
101
101
118
118
118
118
118
118
118
118
118
123
123
123
123
123
123
123
108
324
10
25
18
26
8
1. Remove two M10X25mm Bolts (108) from two Weight Guide Tubes (10).
2. Insert two Weight Guide Tubes (10) into the Bottom Cross Connector (24), using two M10X25mm
Bolts (108).
3. Attach the Support Frame (26), the Arm Support Frame (18) and the Rear Upright Frame (25) to
the Base Frame (3), using six M10X60mm Carriage Bolts (104), six M10 Washers (118) and six
M10 Nylon Nuts (123).
4. Attach the Bottom Cross Connector (24) and the Right Base Frame (8) to the Base Frame (3), using
two M10X75mm Hex Bolts (101), four M10 Washers (118) and two M10 Nylon Nuts (123).

24
112
30
68
60
44
20
56
57
43
58
10
3
26
1. Attach the Lower Fixed Tube (30) to the Weight Guide Tube (10), using two M8X16mm Hex
Bolts (112), and be close to the Bottom Cross Connector (24).
2. Slide four Rubber Rings (68) onto two Weight Guide Tubes (10).
3. Slide fifteen Weight Plates (44) down two Weight Guide Tubes (10).
4. Slide the Selector Shaft Bushing (57) down the Selector Shaft (20) at first hole fix with the
Selector Shaft Pin (56).
5. Insert the Selector Shaft (20) into hole of the Weight Plate (44).
6. Slide the Top Weight Plate (43) down the Selector Shaft (20). Insert the Weight Selector Pin
(60) into hole of desired Weight.
7. Put the Plastic Washer (58) on the Top Weight Plate (43).

29
112
102
102
108
99
112
29
109
124
94
118
118
118
118
118
118118
123 123
123
123
118
102
10
25
26
23
9
10
23
1. Attach the Upper Cross Beam (9) to the Rear Upright Frame (25), using two M10X70mm Hex Bolts
(102), four M10 Washers (118) and two M10 Nylon Nuts (123).
2. Attach the Upper Cross Beam (9) to the Support Frame (26), using two M10X90mm Hex Bolts (99),
four M10 Washers (118) and two M10 Nylon Nuts (123).
3. Attach the Upper Fixed Tube (29) to the Weight Guide Tube (10), using two M8X16mm Hex Bolts
(112).
4. Attach the Buffer (94) to the Top Fixing Bracket (23), using one M10X65mm Bolt (109) and two
M10 Nuts (124).
5. Remove two M10X25mm Bolts (108) from two Weight Guide Tubes (10).
6. Attach the Top Fixing Bracket (23) to the Weight Guide Tube (10), using two M10X25mm Bolts(108).
Note: Attach the Upper Fixed Tube (29) to the Weight Guide Tube (10), and be Close to the Top
Fixing Bracket (23).
7. Attach the Top Fixing Bracket (23) to the Upper Cross Beam (9), using two M10X70mm Hex Bolts
(102), four M10 Washers (118) and two M10 Nylon Nuts (123).

101
101
102
103
119
119
118
118
118
118
118
118
118
123
123
123
123
116
26
15
18
3
2
1
17
16
1. Attach the Footplate Connector (1) and the Front Base Frame (2) to the Base Frame (3), using two
M10X75mm Hex Bolts (101), four M10 Washers (118) and two M10 Nylon Nuts (123).
2. Attach the Footplate (16) to the Footplate Connector (1), using the Footplate Fixed Tube (17) and two
M5X5 Screws (116).
3. Attach the Arm Bracket (15) to the Support Frame (26), using two M10X70mm Hex Bolts (102), four
M10 Washers (118) and two M10 Nylon Nuts (123).
4. Attach the Arm Bracket (15) to the Arm Support Frame (18), using two M10X65mm Hex Bolts (103),
two Washers (
￠ 28X ￠ 10) (119), two M10 Washers (118) and two M10 Nylon Nuts (123).

72
61
102
101 103
99
118
118
118
118
118
118
118
118
118
118
123
123
123
123
123
123
26
28
13
5
6
1
4
1. Attach the Backrest Frame (28) to the Support Frame (26), using one M10 Washer (118), one M10
Nylon Nut (123).
2. Attach the Seat Support Frame (4) to the Support Frame (26), using two M10X90mm Hex Bolts
(99), four M10 Washers (118) and two M10 Nylon Nuts (123).
3. Attach the Front Support Frame (5) to the Seat Support Frame (4), using one M10X65mm Hex Bolt
(103), two M10 Washers (118) and one M10 Nylon Nut (123).
4. Attach the Front Support Frame (5) to the Footplate Connector (1), using two M10X70mm Hex
Bolts (102), four M10 Washers (118) and two M10 Nylon Nuts (123).
5. Attach the Leg Extension Frame (6) to the Front Support Frame (5), using two Plastic Bushing
(
￠ 50X ￠ 11) (72), one M10X75mm Hex Bolt (101), two M10 Washers (118) and one M10 Nylon
Nut (123).
6. Insert the Seat Frame (13) into the Seat Support Frame (4), using one Quick Knob (short) (61).

127
127
118
128
107
129
107
129
118
128
63
63
63
63
63
63
63
63
96
96
12
62
73
73
73
42
42
42
61
67
67
114
114
114
117
117
117
117
122
122
122
122
6
7
5
14 11
9
19
19
15
1. Attach two Arms (19) to the Arm Bracket (15), using two Axle Collars (67) and four M6X6mm
Screws (114).
2. Attach the Left and Right Connect Frame (11&12) to the Upper Cross Beam (9), using six Oil
Bushings (big) (63), one Shaft (96), two M16 Washers (117) and two M16 Nylon Nuts (122).
3. Attach the Press Arm (14) to the Left and Right Connect Frame (11&12), using six Oil Bushings
(big) (63), one Shaft (96), two M16 Washers (117) and two M16 Nylon Nuts (122).
4. Insert the Quick Knob (long) (62) through the single hole on the Press Arm (14) to any one
of the holes on the fan-type plate.
5. Insert the Handle Tubes (127) into the Press Arm (14), using two M10X20mm Hex Bolts (128), two
M10 Washers (118), two M10X35mm (107) and two M10 Arc Washers (129).
6. Insert the Foam Roller Bracket (7) into the Front Support Frame (5), using one Quick Knob
(short) (61).
7. Slide four Leg Foam Rollers (42) onto the Leg Extension Frame (6) and the Foam Roller Bracket
(7), then tap four 25mm Round End Caps (73) into the Leg Extension Frame (6) and the Foam
Roller Bracket (7).

39
40
41
110
112
111
120
120
120
120
120
13
28
26
1. Attach the Head Cushion (41) to the Support Frame (26), using two M8X85mm Hex Bolts (110) and
two M8 Washers (120).
2. Attach the Backrest Cushion (40) to the Backrest Frame (28), using two M8X16mm Hex Bolts (112)
and two M8 Washers (120).
3. Attach the Seat Cushion (39) to the Seat Frame (13), using two M8X40mm Hex Bolts (111) and two
M8 Washers (120).