Fuji Xerox DocuPrint 3105 User manual

26 1 Printer Environment Settings
1 Printer Environment Settings
When you are finished installing your printer using the ‘Setup Guide’, go on to set up its
operating environment.
1.1 Supported Operating Environments
The printer can be used both as a local and a network printer. When used as a local printer,
the printer is connected directly to a computer. Connect the printer to a network for use as
a network printer.
Set all ports you want to use to [Enabled] on the control panel.
Using the Printer as a Local Printer
When using the printer as a local printer, the printer and a computer can be connected using
the following methods:
• USB connection: Connecting the printer and a computer using a USB cable.
(default: [Enabled])
• Parallel connection: Connecting the printer and a computer using a parallel cable. To use
this feature, the Parallel Port Kit (optional) must be installed. (default:
[Disabled])
Using the Printer as a Network Printer
When using the printer as a network printer, the printer can be set up in the following
environments:
• LPD : Used when using TCP/IP protocol to enable direct communication
between the printer and a computer. (default: [Enabled])
• Port9100 : Used when using a Port9100 port.
(default: [Enabled])
•NetWare
®: Used when sharing and managing the printer using a NetWare server.
(default: [Disabled])
Internet
IPP
Network Connection
NetWare/Windows Shared Printer
Network Connection
LPD/SMB/Port9100/EtherTalk/WSD*
Server
Local Connection
Parallel/USB
*: WSD stands for Web Services on Devices.

1.1 Supported Operating Environments 27
• SMB : Used when printing using a Windows®network.
(default: [Enabled])
• IPP : Used when printing via the Internet.
(default: [Disabled])
•EtherTalk
®: Used when printing from Macintosh. (default: [Disabled])
• WSD* : Can be used when printing from Windows Vista®, Windows®7,
Windows Server®2008, or Windows Server®2008 R2. (default:
[Enabled])
*: WSD stands for Web Services on Devices.
Supported Operating Systems and Operating Environments
Note
• The supported operating systems are subject to change without prior notice. Visit our web site for the
latest information.
Refer to
• For information on how to print PostScript data, refer to the manual on the PostScript Driver Library CD-
ROM.
Connectivity Local Network
Port Name
Parallel
*1
USB
*2
LPD NetWare SMB IPP Port
9100
Ether
Talk
Bon-
jour WSD
*3
Protocol --
TCP/
IP
TCP/
IP
IPX/
SPX
Net
BEUI
TCP/
IP
TCP/
IP
TCP/
IP
Apple
Talk
TCP/
IP
TCP/
IP
Windows
®
2000

‐‐‐
Windows
®
XP

‐‐‐‐
Windows Vista
®

‐‐‐ 
Windows
®
7

‐‐‐ ‐‐ 
Windows Server
®
2003

‐‐‐‐
Windows Server
®
2008

‐‐‐ 
Windows Server
®
2008 R2

‐‐‐ ‐‐ 
Mac OS 9.2.2
‐‐‐ ‐ ‐‐ ‐‐ ‐‐
Mac OS X
10.3.9 - 10.4.6,
10.4.8 - 10.4.11,
10.5, 10.6
‐ ‐‐‐‐‐‐
*1: To use this feature, the Parallel Port Kit (optional) must be installed.
*2: The computer must be connected to the printer via a USB 2.0 port.
*3: WSD stands for Web Services on Devices.

28 1 Printer Environment Settings
OS and Available Print Drivers
OS Print Driver Note
Windows
®
2000
Windows
®
XP
Windows Vista
®
Windows
®
7
Windows Server
®
2003
Windows Server
®
2008
Windows Server
®
2008 R2
PCL Print
Driver
Installing the print driver is available from the Driver CD
Kit CD-ROM.
Refer to the ‘CD-ROM Documentation (HTML)’ on the
CD-ROM.
PostScript
Print Driver
Installing the print driver is available from the PostScript
Driver Library CD-ROM.
Refer to the manual on the PostScript Driver Library CD-
ROM for details.
Mac OS
9.2.2
10
. 3 . 9-10 . 4 . 6,
10
. 4 . 8-10 . 4 . 11,
10
. 5-10 . 6
PostScript
Print Driver
Installing the print driver is available from the PostScript
Driver Library CD-ROM.
Refer to the manual on the PostScript Driver Library CD-
ROM for details.

1.2 Connecting a cable 29
1.2 Connecting a cable
Connect the printer to your computer using an interface cable appropriate for your
connection method.
An interface cable is not included with the printer. You must purchase it separately.
USB Connection
When using a USB connection, install the printer driver on the computer after connecting
the cable. For the installation method, refer to “1.7 Installing a Print Driver” (P. 43) and
"Manual (HTML Document)" on the CD-ROM disk of the driver CD kit.
1. Connect the USB cable to the interface
connector.
2. Connect the other end of the USB cable to
the computer.
Network Connection
Use 1000BASE-T (When the optional Gigabit Ethernet Board Card is installed) or a straight-
type network cable that supports 100BASE-TX or 10BASE-T.
1. Switch off the printer's power.
2. Wind the network cable around the
supplied ferrite core and close the ferrite
core.
Note
• Do not wind the cable to tightly or it may break.
A connector to be
connected to the printer
Ferrite core
Approx. 7cm

30 1 Printer Environment Settings
3. Connect the network cable to the interface
connector on the printer.
Note
• The location of the connector differs depending on
whether Gigabit Ethernet Board Card is installed or
whether the standard configuration is used. Connect
the appropriate connector for your environment.
• When the Gigabit Ethernet Board Card is installed, the
connector for the standard configuration cannot be
used.
• The MAC address is the same as in the standard
configuration when installing the Gigabit Ethernet
Board Card.
• LED1 on the Gigabit Ethernet Board Card lights up as
follows according to the network environment
connected.
10BASE-T environment: Off
100BASE-TX environment: Lights in yellow
1000BASE-T environment: Lights in blue
4. Connect the other end of the network cable
into a network device such as a hub.
5. Switch on the printer's power.
Note
• The interface connecter for standard network cannot be used when the Gigabit Ethernet Board Card is
installed to the printer.
• When installing both Gigabit Ethernet Board Card and Feature Enhance Kit, install the Feature Enhance
Kit first.
• Message [Ready to print IP Address failed] may be displayed on the control panel. To erase this
message, set to [STATIC] in [Network / Port] > [TCP/IP Settings] > [IPv4 Settings] > [Get IP Address] to
specify IP address (Example: 192.168.1.100) or [Disabled] for each port other than the USB port in
[Network / Port].
Refer to
• For setting method of IP address, refer to “1.4 Setting the Network Environment” (P. 33).
• For setting each port, refer to “1.5 Enabling Ports” (P. 37) “.
Standard configuration
Gigabit Ethernet Board Card

1.2 Connecting a cable 31
Parallel Connection
When using a parallel connection, you must first install the optional Parallel Port and
connector conversion cable.
Important
• Parellel Port Kit (optional) and Gigabit Ethernet Board Card (optional) cannot be installed at the same
time.
.1. Switch the printer off.
2. Insert the connector conversion cable
included with the optional Parallel Port into
the interface connector on the printer.
3. Connect the other end of the connector
conversion cable to the connector on the
parallel cable. Then secure it using the
metal pieces on both sides of the
connector.
4. Plug the other end of the parallel cable into
your computer.
5. Switch the printer on.
Important
• Parallel Port Kit (Optional) and Gigabit Ethernet Board Card cannot be installed concurrently. If the
Parallel Port Kit (Optional) is installed, remove the card by reference to “ Removing the Parallel Port Kit
(Optional)” (P. 344).

32 1 Printer Environment Settings
1.3 Switching the Control Panel Display
Language
Select one display language from among [English], [Korean], [Simp.Chinese], and
[Trad.Chinese] for the control panel of the printer.
The following explains how to switch the control panel display language.
1. Press the <Printer Settings> button to
display the menu screen.
2. Press the < > button until [Language] is
displayed.
Note
• If you went past the desired item, return to the item by
pressing the < > button.
3. Press either the < > or <OK> button to
select.
The language is displayed.
4. Press the < > button until the desired
language is displayed.
5. Press the <OK> button to confirm.
6. Press the <Printer Settings> button to
close the menu.
The printer automatically restarts.

1.4 Setting the Network Environment 33
1.4 Setting the Network Environment
This section explains how to install your printer in a TCP/IP environment. When installing
the printer in a different environment, refer to the ‘CD-ROM Documentation (HTML)’ on the
Driver CD Kit CD-ROM.
Note
• The printer can use an IPv6 address in an IPv6 network environment. For information on using IPv6
addresses, refer to “Setting an IP Address (IPv6)” (P. 36).
Setting an IP Address (IPv4)
To use TCP/IP protocol, you must configure an IP address for the printer.
By default, the printer is set to obtain its IP address (via the [Get IP Address] setting on the
control panel) using [DHCP/Autonet]. Thus, when the printer is connected to a network that
has a DHCP server, the printer automatically obtains its IP address from the server.
Print the [Configuration Report] to see if the printer already has an IP address.
If the printer does not have an IP address, set [Get IP Address] to [STATIC] and configure
the address.
Note
• For information on how to print the [Configuration Report], refer to “7.2 Printing Reports/Lists” (P. 260).
• The printer can also obtain its IP address by using a BOOTP or RARP server. If using a BOOTP or
RARP server, set [Get IP Address] to [BOOTP] or [RARP].
• If using a DHCP server, the printer’s IP address may change without notice. Make sure to check the
address periodically.
The following explains how to set up an IP address on the Control Panel. Depending on your
network environment, your printer also needs a subnet mask and gateway address. Consult
your network administrator for the settings required for your printer.
To Set the IP Address
Important
• Addresses including IP address, subnet mask and gateway address depend on your network
environment. Consult your network administrator for setting addresses.
1. On the control panel, press the <Printer
Settings> button to display the menu
screen.
If an IP address is listed,
skip the following procedure.
If an IP address is not listed,
or if you want to change the
current IP address, configure
the setting using the
following procedure.[■To Set
the IP address].
Settings
LanguageEmulation

34 1 Printer Environment Settings
2. Press the < > button until [Admin Menu] is
displayed.
Note
• If you went past the desired item, return to the item by
pressing the < > button.
3. Press the < >or <OK> button to select.
[Network / Port] is displayed.
Note
• If you pressed the < > or <OK> button on the wrong
item, return to the previous screen by pressing the
< > or the <Back> button.
• To start over from the beginning, press the <Printer
Settings> button.
4. Press the < > or <OK> button to select.
[LPD] is displayed.
Note
• [Parallel] appears only when the Parallel Port Kit
(optional) is installed.
5. Press the < > button until [TCP/IP
Settings] is displayed.
6. Press the < > or <OK> button to select.
[IP Mode] is displayed.
7. Press the < > button until [IPv4 Settings]
is displayed.
8. Press the < > or <OK> button to select.
[Get IP Address] is displayed.
9. Press the < > or <OK> button to select.
The current set value is displayed.
10. Press the < > button until [STATIC] is
displayed.
11. Press the <OK> button to confirm your
selection.
If [000.000.000.000] appears, skip to step
15.
12. Press the < > or <Back> button to return
to [Get IP Address].
Settings
Admin Menu
Admin Menu
Network / Port
Network / Port
LPD
Network / Port
TCP/IP Settings
TCP/IP Settings
IP Mode
TCP/IP Settings
IPv4 Settings
IPv4 Settings
Get IP Address
Get IP Address
• DHCP / Autonet
Get IP Address
STATIC
Get IP Address
• STATIC
IPv4 Settings
Get IP Address