Fujitsu F2MC-8FX MB2146-213 User manual

FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM SS01-26013-1E
F2MC-8FX Family
LQFP-48P (0.5 mm pitch) HEADER BOARD
MB2146-213
OPERATION MANUAL

PREFACE
Thank you for purchasing the LQFP-48P (0.5 mm pitch) *1header board (model number : MB2146-
213) for the F2MC *2-8FX family.
MB2146-213 is a header board used to connect the MCU board (model number : MB2146-301,
MB2146-303) which mounts F2MC-8FX family evaluation MCU to a user system.
This manual explains the handling of the MB2146-213. Before using MB2146-213, be sure to read
this manual.
Consult the Sales representatives or the Support representatives of Fujitsu Limited for mass-pro-
duced MCUs and evaluation MCUs which correspond on MB2146-213.
MB2146-213 is an object about MCU with a built-in LCD controller.
*1 : The lead pitch of package (FPT-48P-M26) is 0.5 mm and the body size is 7 mm ×7 mm.
*2 : F2MC is the abbreviation used for FUJITSU Flexible Microcontroller.
■Caution of the products described in this document
The following precautions apply to the product described in this manual.
CAUTION The wrong use of a device will give an injury and may cause malfunction on cus-
tomers system.
Cuts This product has parts with sharp points that are exposed.
Do not touch an edge of the product with your bare hands.
Damage
When connecting the header board to the user system, correctly position the index
mark (▲) on the NQPACK mounted on the user system with the 1 pin direction(1)
on the header board, otherwise the MCU board and user system might be dam-
aged.
Damage When mounting a mass production MCU, correctly position pin 1, otherwise the
mass production MCU and user system might be damaged.
i

Copyright ©2006 FUJITSU LIMITED All rights reserved
•The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales representatives before ordering.
•The information, such as descriptions of function and application circuit examples, in this document are presented sole-
ly for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU
does not warrant proper operation of the device with respect to use based on such information. When you develop
equipment incorporating the device based on such information, you must assume any responsibility arising out of such
use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the infor-
mation.
•Any information in this document, including descriptions of function and schematic diagrams, shall not be construed
as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right
of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property
right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
•The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in
connection with above-mentioned uses of the products.
•Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire pro-
tection, and prevention of over-current levels and other abnormal operating conditions.
•If any products described in this document represent goods or technologies subject to certain restrictions on export un-
der the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be
required for export of those products from Japan.
ii

1
1. Product Outline
■Product outline
MB2146-213 is a header board (referred to as header board) used to connect the MCU board (model
number : MB2146-301, MB2146-303) which mounts an evaluation MCU in the F2MC-8FX family
of Fujitsu 8-bit microcontrollers to a user system. To build an F2MC-8FX evaluation environment,
combine the three products as shown in Figure 1: the header board, an MCU board, and a BGM
adapter (model number : MB2146-09).
Figure 1 System Configuration
■Product configuration
Table 1 lists the product configuration in the header board, and Table 2 lists options.
Table 1 Product Cofiguration
Table 2 Options
* : Multiple types of evaluation MCUs are available depending on their applications. Purchase the one that satisfies
the service conditions.
Name Description Remarks
F2MC-8FX
LQFP-48P (0.5 mm pitch)
header board
[Model number : MB2146-213]
Connector/LQFP48pin
(0.5 mm pitch) Package conversion -
[Model number : YQPACK048SD]
(Tokyo Eletech Corporation) I/F between header board and NQPACK Accessory (Connected)
[Model number : NQPACK048SD]
(Tokyo Eletech Corporation) For mounted on the user system Accessory
[Model number : HQPACK048SD]
(Tokyo Eletech Corporation)
Used when mounting mass production MCU
to NQPACK. Accessory
Name Description Remarks
BGM adapter
[Model number : MB2146-09] ICE unit for F2MC-8FX -
MCU board
[Model number : MB2146-301, MB2146-303]
Built-in MB95FV100B-101,
MB95FV100B-103 Built-in F2MC-8FX evaluation MCU *
㪤㪙㪉㪈㪋㪍㪄㪇㪐
MCU board
BGM adapter
Header board

2
2. Checking the Delivered Product
Before using the MB2146-213, confirm that the following components are included
in the box:
•LQFP-48P (0.5 mm pitch) header board *1: 1
•Screws for securing header board (M2 ×10 mm, 0.4 mm pitch) : 4
•NQPACK048SD *2: 1
•HQPACK048SD *3: 1
•Operation manual (English version, this manual) : 1
*1 : Header board manufactured by Tokyo Eletech Corporation, referred to as “YQPACK”, mounts
YQPACK048SD.
*2 : IC socket manufactured by Tokyo Eletech Corporation, referred to as “NQPACK”, is supplied
with a special screwdriver and 2 guide pins. A socket offering higher reliability,
NQPACK048SD-SL (manufactured by Tokyo Eletech Corporation and sold separately) , can
be used by making an IC socket mounting hole on the user system board. For more informa-
tion, contact Tokyo Eletech Corporation.
*3 : IC socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, is
supplied with 4 screws for securing HQPACK (M2 ×6 mm, 0.4 mm pitch) .
3. Handling Precautions
The header board is precision-manufactured to improve the dimensional accuracy and to ensure a
reliable contact. The header board is therefore sensitive to mechanical shocks. To ensure a correct
use of the header board in the proper environment, observe the following:
•Avoid placing a stress on the NQPACK mounted on the user system board when connecting
the header board.

3
4. Notes on Designing
■Notes on designing printed circuit board for the user system
When the header board is connected to the user system, some parts mounted around the NQPACK
in the user system may be contacting the header board if the height of the part is tall. To prevent this,
design the printed circuit board for the user system so that the components do not exceed the height
shown in Figure 2. Figure 2 shows the dimension figure of the header board.
Figure 2 Header Board Dimensions
㪈 㪉
㪈㪈㪐
㪈㪉㪇
㪚㪥㪉
㪈 㪉
㪈㪈㪐
㪈㪉㪇
㪚㪥㪈
㪚㪥㪊
㪬㪈
40.0 mm
30.0 mm
40.0 mm
Approximately
13.0 mm *1
NQPACK048SD
:Tokyo Eletech Corporation
YQPACK048SD
:Tokyo Eletech Corporation
WR-120SB-VF-N1 : JAE *2
PCW-1-1-1PW
:MAC EIGHT
WR-120SB-VF-N1 : JAE *2
U1: User system I/F connector
CN3: Incorrect insertion prevention socket
CN1/CN2: MCU board I/F connector
*1 : The height differs slightly depending on how the YQPACK and NQPACK are engaged.
*2 : Japan Aviation Electronics Industry, Limited

4
■MCU footprint design notes
Figure 3 shows the recommended footprint dimensions of the NQPACK mounted on the printed cir-
cuit board for the user system. Take the footprint in Figure 3 into consideration as well as the foot-
print of the mass production MCU when designing the printed circuit board for the user system.
To follow the most updated information, be sure to contact Tokyo Eletech Corporation whenever de-
signing the printed circuit board.
Figure 3 Recommended Footprint Dimensions for Mounting the NQPACK
No.1 Pin
10.0 mm
1.5 mm
0.5 mm 0.25 mm
7.0 mm

5
5. Connecting to the User System
■Connecting
Mount the supplied NQPACK on the user system before using the MB2146-213.
1. To connect the header board to the user system, match pin 1 indicated by the index mark (▲) on
the NQPACK mounted on the user system with pin 1 indicated by the index mark (an angle cut
linearly at one place only in silk screen) on the header board and then insert it (See “Figure 4”) .
The pins of YQPACK are thin and easy to bend. Insert NQPACK after confirming that the pins
of YQPACK are not bent.
Figure 4 Index Position
2. Insert each screw for securing the header board into each of the four tapped holes on the header
board, and then tighten the screws diagonally. The center screw hole is not used. To tighten the
screws, use the special screwdriver supplied with the NQPACK to equally tighten the four screws
in sequence. Tightening the screws too tight might result in a defective contact.
3. Connect the MCU board to the header board while being careful not to excessively force the NQ-
PACK. The MCU board can be connected to the header board only in the correct orientation as
they have an incorrect insertion prevention header socket to prevent a reverse connection. Figure
5 illustrates how the MCU board, header board, NQPACK, and user system are connected togeth-
er.
13
12
1
48 37
36
25
24
NQPACK index mark
Header board index mark

6
Figure 5 Connecting MCU Board/Header Board to User System
■Disconnection
1. Remove the MCU board from the header board. Detach the four corners slowly in sequence, not
excessively forcing the junction with the NQPACK.
2. Remove all of the four screws from the header board. Pull out the header board vertically from
the NQPACK. Remove the header board slowly not excessively forcing the junction with the
NQPACK.
YQPACK
Header board
User system
NQPACK
MCU board
MCU board
Connected
at shipment
Screws for securing
header board
Evaluation
MCU

7
6. Mounting Mass Production MCUs
■Mounting
To mount a mass production MCU on the user system, use the supplied HQPACK (IC socket cover)
(see “Figure 6”) .
1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQ-
PACK mounted on the user system with the index mark (●) on the mass production MCU.
2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, match the
index mark of HQPACK with the index mark of NQPACK and insert it (angle cut linearly at one
place only) .
The pins of HQPACK are thin and easy to bend. Insert NQPACK after confirming that the pins
of HQPACK are not bent.
3. Insert each screw for securing HQPACK in each of four tapped holes on the HQPACK, and then
tighten the screws diagonally. To tighten the screws, use the special screwdriver supplied with
the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight
might result in a defective contact.
Figure 6 Mounting a Mass Production MCU
■Disconnection
To remove the HQPACK, remove all of the four screws and pull out the HQPACK vertically from
the NQPACK. When taking out the mass production MCU, absorb the mass production MCU using
a vacuum pick-up tool special for removing IC. Do not attempt to remove the mass production MCU
forcibly, for example, using a screwdriver to do so can bend the pins of the mass production MCU
or break the NQPACK.
Screws for securing HQPACK
HQPACK
Mass production MCU
NQPACK
User system