Fujitsu LQFP-100P User manual

FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM SS01-71048-1E
DSU-FR EMULATOR
LQFP-100P HEADER TYPE5
MB2198-129
OPERATION MANUAL

PREFACE Thank you for purchasing the LQFP-100P header type5 (MB2198-129) for the DSU-FR emulator.
The LQFP-100P header type5 is used to connect the DSU-FR emulator (MB2198-01*3) and the
DSU-FR emulator PGA-401P adapter type2 (MB2198-130*4) to a user system. That uses Fujitsu FR
*1 family micro controller MB91270 series (LQFP-100P*2).
This manual explains thehandling of the LQFP-100P header type5 for the DSU-FR emulator. Before
using the MB2198-129, be sure to read this manual.
Consult the Sales Department or the Support Department of adapter Fujitsu Limited for mass-pro-
duction MCUs and evaluation MCUs.
*1 : FR is the abbreviation used for FUJITSU RISC CONTROLLER.
*2 : The lead pitch of PACKAGE (FPT-100P-M05) is 0.5 mm and the body size is 14 mm × 14 mm.
*3 : referred to as "emulator"
*4 : referred to as "adapter board"
■Handling and use
The handling and use of this product and notes regarding safety are included in the hardware manual
of the DSU-FR emulator.
Follow the instructions in for the use of this product.
•DSU-FR EMULATOR MB2198-01 HARDWARE MANUAL
•DSU-FR EMULATOR PGA-401P ADAPTER TYPE2 MB2198-130 OPERATION MANU-
AL
■Caution of the products described in this document
The following precautions apply to the product described in this manual.
CAUTION The wrong use of a device will give an injury and may cause malfunction on cus-
tomers system.
Cuts This product has parts with sharp points that are exposed.
Do not touch edge of the product with your bare hands.
There is a possibility that it may be injured.
Damage When connect the header board to the user system, correctly position the index
mark (▲) on the NQPACK mounted on the user system with the index mark (▲)
on the header board, otherwise the emulator system and user system might be
damaged.
Damage When mounting a mass production MCU, correctly position pin 1, otherwise the
mass production MCU and user system might be damaged.

©2005 FUJITSU LIMITED Printed in Japan
•The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales representatives before ordering.
•The information, such as descriptions of function and application circuit examples, in this document are presented sole-
ly for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU
does not warrant proper operation of the device with respect to use based on such information. When you develop
equipment incorporating the device based on such information, you must assume any responsibility arising out of such
use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the infor-
mation.
•Any information in this document, including descriptions of function and schematic diagrams, shall not be construed
as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right
of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property
right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
•The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in
connection with above-mentioned uses of the products.
•Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire pro-
tection, and prevention of over-current levels and other abnormal operating conditions.
•If any products described in this document represent goods or technologies subject to certain restrictions on export un-
der the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be
required for export of those products from Japan.

1
1. Checking the Delivered Product
Before using the LQFP-100P header type5, confirm that the following components are included in
the box:
•LQFP-100P header type5 *1 : 1
•Screws for securing header board (M2 ×10 mm, 0.4 mm pitch) : 4
•Washer : 4
•NQPACK100SD-ND*2 : 1
•HQPACK100SD*3 : 1
•Operation manual (Japanese version) : 1
•Operation manual (English version, this manual) : 1
*1 : Referred to as "header board". Header board is mounted on YQPACK100SD (Tokyo Eletech
Corporation), referred to as “YQPACK”.
*2 : IC socket manufactured by Tokyo Eletech Corporation, referred to as “NQPACK”, and sup-
plied with a special screwdriver and 3guide pins. A socket offering higher reliability,
NQPACK100SD-ND-SL (Tokyo Eletech Corporation, sold separately), can be used by mak-
ing an ICsocket mounting hole on the user systemboard. For more information, contact Tokyo
Eletech Corporation.
*3 : IC Socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, with
4 screws for securing HQPACK (M2 ×6 mm, 0.4 mm pitch).
This product is used as an emulator system by combining with an optional emulator and adapter
board.
Consult the Sales Department or the Support Department of Fujitsu Limited for the adapter or the
emulator of this product.
2. Handling Precautions
The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable
contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header
in the proper environment, observe the following points regarding its insertion and removal:
•To avoidplacing stress on the NQPACK mounted on the user system board during connecting
the header board.

2
3. Notes on Designing
■Restrictions of PC board for the user system
Once the header board is connected to the user system, the heights of parts mounted in the space
around the header board are restricted.
The PC board of the user system must be designed with due consideration given to this restriction
(Figure 1).
* : The height differs slightly depending on how the YQPACK and the NQPACK are en-
gaged.
Figure 1 Header board dimensions
A1 B1
A50 B50
A1 B1
A50 B50
CN1 CN2 CN3
BA
S2 S1
78
80
32
Approximately
35 *
Approximately
13 *
36
UNIT: mm

3
■MCU footprint design notes
Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board
of the user system.
The PC board of the user system must be designed with due consideration given to this footprint as
well as to the mass production MCU.
For more information, contact the Tokyo Eletech Corporation.
*1 : It is a position of hole (φ1.0) for the guide pin to fit position when NQPACK is mounted.
When the guide pin is not used, it is not necessary to puncture it.
*2 : It is a fixation of screw hole (φ2.2) for IC socket made when NQPACK100SD-ND-SL
(Tokyo Eletech Corporation, sold separately) is mounted. When the NQPACK100SD-
ND-SL is not used, it is not necessary.
Figure 2 Recommended dimensions of the footprint for mounting the NQPACK
0.5 0.25
No
.1
Pin
2.0
UNIT:mm
0.5 ×24 =12
0.5 ×24 =12
2.0
2.0 2.0
5.8
5.8
13
13
φ2.2*2
3-φ1.0*1

4
4. Procedure for Connecting the User System
Before using the LQFP-100P header type5, mount the supplied NQPACK on the user system.
The header board is used combining the emulator. Moreover, connection of a header board and
an adapter board is two flat cables (a standard or Long)appended to the emulator main part. Please
use it.
Refer to the hardware manuals of the emulator or the adapter board about the way to connect.
■Connecting
1. To connect the header board to the user system, match the index mark (▲) on the NQPACK-
mounted on the user system with the index mark (▲) on the header board and then insert it (See
Figure 3) . The pin of YQPACK is thin and easy to bent. Insert NQPACK after confirm that the
pin of YQPACK is not bent.
2. Insert each screw for securing header board in each of the four drilled holes on the header
board(See Figure 4).
To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten
the four screws in sequence. Please tighten a screw to a diagonal by equal power using a special
screwdriver. Tightening the screws too tight might result in a defective contact.
Figure 3 Index Position
NQPACK Index (▲)
Header board Index (▲)
Flat cable connector B
Flat cable connector A
YQPACK
(It mounts in the back)

5
Figure 4 Header board connection
■Disconnection To disconnect the header board from the user system, remove all four screws, and then pull the head-
er board straight out of the socket.
Screws for securing
header board
Washer
YQPACK
NQPACK
Header board
User system

6
5. Mounting Mass Production MCUs
To mount a mass production MCU on the user system, use the supplied HQPACK (See Figure 5).
■Mounting
1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQ-
PACKmounted on the user system with the index mark (●) on the mass production MCU.
2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, insert the
HQPACK into a NQPACK.
The pin of HQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of HQ-
PACK is not bent.
3. Insert each screw for securing HQPACK in each of the four drilled holes on the HQPACK,(See
Figure 5).
To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten-
the four screws in sequence. Please tighten a screw to a diagonal by equal power using a special-
screwdriver. Tightening the screws too tight might result in a defective contact.
Figure 5 Mounting a mass production MCU
■Disconnection To remove the HQPACK, remove all four screws, and pull out the HQPACK vertically.
Screws for securing HQPACK
HQPACK
Mass production MCU
NQPACK
User system

7
6. Connector Pin Assignment
The signal of Evaluation MCU with which it was carried on the adapter board is connected to YQ-
PACK (the same assignments as production MCU) via the flat cable connector (A,B) on a header-
board.
Connection of a header board and an adapter board is two flat cables (a standard or Long) appended
to the emulator main part. Please use it.
Please check the hardware manual of an emulator or an adapter board about reference of the connec-
tionmethod.
For details on the production MCU's pin information, refer to the datasheet or hardware manual for
the relevant MCU.
■Pin Assignment
Tables 2 and 3 list the pin assignments among the probe connector, the evaluation MCU on the
adapter board, and the mass production MCU.
For details on the names of signal conductors of the evaluation MCU, refer to the hardware manual
for the emulator or adapter board.
Comments in the tables are given below.
*1 : Connected to the mass production MCU pin:VSS (pins 14, 42, 64 and 89).
*2 : Connected to the mass production MCU pin:C (pin15).
*3 : Connected to the mass production MCU pin:VCC (pins 13, 63 and 83).
*4 : Header board control pin (not connected to the mass production MCU).
*5 : Connected to the Evaluation MCU pin (pins 38, 51, 87 and 209) :It connects with a terminal-
block and connects with mass production MCU terminal (pins 11 and 12) with the jump-er
plug, respectively.
Figure 6 Pin Assignment
Table 1 Jumper Plug Setup
*6 : In Evaluation MCU, since it becomes a non-connected terminal, it connects with the pull-up
(10K ohm)
*7 : In Evaluation MCU, since it becomes a non-connected terminal, it connects with the pull-up
(10K ohm)
Jumper Plug Setup (S1,S2) Item Mass production MCU
A-B MB91F272
B-C MB91F272R
Evaluation MCU S1
S2
12 pin
11 pin
C
A
B
C
B
A
Mass production MCU
38 pin
51 pin
87 pin
209 pin