Fujitsu FTP-632MCL001 User manual

FTP-632MCL001/002/303/304
■OVERVIEW
FTP-632MCL/FTP-622DCL Series is an ultra high speed line
thermal printer driven by 24 VDC, printing on 3-inch wide paper
(80 mm/85 mm).
This printer is compact and light weight, and the design allows
easy head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label printers,
medical instruments, etc. A printer with a specially designed
cutter is also available.
■HIGHLIGHTS
• Ultra high speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using
Fujitsu Components' unique head drive control.
• Compact and lightweight
This printer has a low profile of only 20 mm, and a light
weight of approximately 94 g.
• Low power consumption
The peak current for head driving is approximately 2.9 A (at
80 mm/s printing speed, 50% printing ratio).
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever
operation.
• ESC/POSTM*1 Commands
The commands conform to ESC/POSTM.
• Auto Cutter
Printer with auto cutter (full cut/partial cut) is also available.
• UL Recognized
File No.E171434
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.
24V DRIVE, HIGH SPEED LINE
THERMAL PRINTER
3” MECHANISM, WITH OR WITHOUT CUTTER
FTP-632MCL001
FTP-622DCL001
FTP-632MCL303/304
1

2
FTP-632MCL001/002/303/304
■DESIGNATION
Part number
Standard FTP-632MCL001/002*1
FTP-632MCL303/304*1
FTP-622DCL001/011*2
FTP-622DSL001/011/012*3
FTP-622CU101*4
FTP-622Y001
FTP-622Y201
FTP-622Y301
FTP-622Y401
Item
Printer mechanism
Interface board
(Continued)
Parallel (Centronics Standard)
Serial (RS232C)
Thermal head cable
Parallel interface cable
Serial interface cable
Power cable
*1: 001/303 is for front paper insertion (curl path) and 002/304 is for rear paper insertion (straight path).
*2: 001/011 supports ANK and 101 supports ANK + Kanji.
*3: 001/011/012 supports ANK and 111 supports ANK + Kanji.
*4: CU101 supports Kanji and cutter control.
■GENERAL SPECIFICATIONS
Cables
LSI(MCU)
Printer mechanism with cutter
Part number FTP-632MCL001/002 FTP-632MCL303/304
Printing method Thermal-sensitive line dot method
Dot structure 576 dots/line
Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density
Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch
Effective printing area 72 mm
MCL001/303 80 mm
Paper width MCL002/304 85 mm
Paper thickness 60~100 µm*160~100 µm*1
Cutter type --- full or partial
Number of columns 48 columns/line (24×12 dot font)
Maximum printing speed 640 dotlines/s (80 mm/s)
Alphanumeric KANA: 159 International characters: 195
Character types JIS KANJI (FTP-622DCL101/111): approximately 6800
24 ×12 dots, (3.0 ×1.5 mm), 48 columns
24 ×24 dots, (3.0 ×3.0 mm), 24 columns
16 ×8 dots, (2.0 ×1.0 mm), 72 columns
16 ×16 dots, (2.0 ×2.0 mm), 36 columns
SpecificationsItem
Character composition, dimensions (H×W),
Number of characters

3
FTP-632MCL001/002/303/304
Part number FTP-632MCL001/002 FTP-632MCL303/304
Interface Centronics (ESC/POSTM), RS232C
24 VDC ±5%, Voltage
Current : average*2( ): Peak
For head 1.11 (1.45) A (at 80 mm/s printing speed, 25% printing ratio)
0.81 (1.45) A (at 50 mm/s printing speed, 25% printing ratio)
0.75 (0.87) A (at 30 mm/s printing speed, 25% printing ratio)
For motor 24 VDC ±5%, 1.0 A maximum
For cutter --- 24 VDC ±5%, 1.0 A maximum
For logic 5 VDC ±5%, 0.5 A maximum
Mechanism 108 (W) ×48 (D) ×20 (H) mm (Excluding lever) 117 (W) ×57 (D) ×38 (H) mm
Interface board 131 (W) ×89 (D) ×24 (H) mm
Weight approximately 94 g approximately 330 g
Expected life Mechanism Pulse durability : 1 ×108pulse/dot (using Fujitsu's standard driving
method)
Wear resistance : 50 km (at 25% printing ratio)
Cutter --- 500,000 cuts
Operating temperature 0 to +50°C*3
Operating humidity 20 to 85% RH (no condensation)
Storage temperature –20 to +60°C (excluding paper)
Storage humidity 5 to 95% RH (no condensation)
Head temperature By thermistor (applied energy control, abnormal temperature detection)
Detection Paper out/Mark detect By photointerrupter
Head-up By microswitch
For front insertion use (80 mm width) : FTP-030PU001, FTP-030P0701
For rear insertion use (85 mm width) : FTP-030P0020, FTP-030P0702
*Recommended papers
· Oji Paper : PD150R, PD160R, PD170R
· NIPPON Paper : TF50KS-E,TF60KS-E,TF60KJ-R
· MITSUBISHI Paper Mills : P220VBB-1, AFP-235
Power supply
Dimensions
SpecificationsItem
(Continued)
Environmental
conditions
Recommended thermal sensitive paper
*1: There may be exceptions.
*2: 24 VDC, minimum head resistance.
*3: Guarantee: +5°C ~+40°C.

4
FTP-632MCL001/002/303/304
■DIMENSIONS
Mechanism
Unit: mm
20.1
(250)47.530.5
21.0
50.957.0
1
(107.9)
HEAD CONNECTOR
3-MOUNTINGHOLE(M2)
2-POSITIONINGHOLE
CENTER OFPAPER
HEAD UPLEVER(AT HEAD DOWN)
+
–
PAPER INSERTION(MCL001)
PAPER
INSERTION
(MCL002)
76.8(POSITIONINGHOLEPITCH)
Interface board
Unit: mm
88.9 78.7
39.4 39.4
5.1
5.15.1
5.15.1
5.1
5.1
5.1
120.7
105.4
120.7
116.8
87.6
130.8
43.295.4
CN10
CN5CN2** CN3
CN1
CN8
CN13
CN11*
19.1
*CN11 on FTP-622DCL011/111 & 622DSL011/112only
**CN2on FTP- 622DSL only
4—ø3.6
FTP-632MCL001/002

5
FTP-632MCL001/002/303/304
Unit: mm
(sensor cable)
(motor cable)
(cutter cable)
3-2.0 or less
Unit: mm
Interface board
88.9 78.7
39.4 39.4
5.1
5.1 5.1
5.1 5.1
5.1
5.1
5.1
120.7
105.4
86.4
120.7
116.8
87.6
130.8
43.2
CN10
CN5 CN3
CN2*
CN1
CN8
CN13CN11
19.1
4-Ø3.6
*CN2 on FTP-622DSL only
■DIMENSIONS
Mechanism
FTP-632MCL303/304

6
FTP-632MCL001/002/303/304
■CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM
1. Thermal Head
Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent
Board side : PHR-16 (J.S.T.) or equivalent
2. Motor connectors
Motor side : PHR-4 (J.S.T.) or equivalent
Board side : B4B-PH-K-S (J.S.T.) or equivalent
*1: Symbol: " " means a negative logic signal
1, 2, 3, ......................................15, 16
Motor Thermal head heat sink Head up level
Connector Pin No.
3. Sensor connectors
Sensor : PHR-5 (J.S.T.) or equivalent
Board side : B5B-PH-K-S (J.S.T.) or equivalent

7
FTP-632MCL001/002/303/304
■INTERFACE, COMMAND, OPTIONS
■FUNCTION
ITEM ITEM
1. Test printing 8. Cutter trouble detection
2. Paper-out detection 9. Motor power save
3. Paper near end detection 10. Mark detection
4. Head-up detection 11. MCU trouble detection
5. Abnormal temperature detection of thermal head 12. Power on/off sequence protection
6. Blown fuse detection 13. Motor protection
7. Abnormal voltage detection of head 14. Hardware timer
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and
Options.
4. Cutter
Mech side : EHR-4 (J.S.T.) or equivalent
Board side : B4B-EH (J.S.T.) or equivalent
© 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 06/2002
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices