Fujitsu PRIMERGY CX25 0 M4 Series Installation instructions

Disassembly and Recycling Instructions - English
FUJITSU Server PRIMERGY
CX400 M4 Server Enclosure
CX25x0 M4/M5 Server Nodes
Disassembly and Recycling Instructions
December 2019

Copyright and Trademarks
Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Documentation creation according
to DIN EN ISO 9001:2015
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2015.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright 2019 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
–The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
–No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

CX400 M4 Disassembly and Recycling Instructions
Version history
Issue number Reason for update
1.0 / December 2019 Initial release

Disassembly and Recycling Instructions CX400 M4

CX400 M4 Disassembly and Recycling Instructions
Contents
1 Disassembly and recycling . . . . . . . . . . . . . . . . . . . 7
1.1 Recycling information . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Disassembly of the server enclosure . . . . . . . . . . . . . . 9
1.2.1 Removing server nodes from the server enclosure . . . . . . . . 9
1.2.2 Removing the ID card and server cover . . . . . . . . . . . . . 12
1.2.3 Removing the hot-plug PSU . . . . . . . . . . . . . . . . . . . 16
1.2.4 Removing fan modules . . . . . . . . . . . . . . . . . . . . . 17
1.2.5 Removing the fan cage . . . . . . . . . . . . . . . . . . . . . 19
1.2.6 Removing the midplane kit . . . . . . . . . . . . . . . . . . . 20
1.2.7 Removing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . 22
1.2.8 Removing 2.5-inch HDD backplanes . . . . . . . . . . . . . . 24
1.2.9 Removing the HDD/SSD bridge board . . . . . . . . . . . . . 25
1.2.10 Removing front bezels . . . . . . . . . . . . . . . . . . . . . . 26
1.2.11 Removing the front panel modules . . . . . . . . . . . . . . . 28
1.3 Disassembly of the server nodes . . . . . . . . . . . . . . . 30
1.3.1 Removing the SXM2 extension tray, SXM2 modules and LC kit 30
1.3.2 Removing the GPGPU extension tray and GPGPUs . . . . . . 42
1.3.3 Removing riser modules and expansion cards . . . . . . . . . 49
1.3.4 Removing an FBU . . . . . . . . . . . . . . . . . . . . . . . . 54
1.3.5 Removing an OCP mezzanine card . . . . . . . . . . . . . . . 56
1.3.6 Removing main memory modules . . . . . . . . . . . . . . . . 57
1.3.7 Removing the heat sink and CPU (Air cooling) . . . . . . . . . 59
1.3.8 Removing the heat sink and CPU (LC) . . . . . . . . . . . . . 61
1.3.9 Removing the iRMC microSD card . . . . . . . . . . . . . . . 69
1.3.10 Removing M.2 SSDs . . . . . . . . . . . . . . . . . . . . . . 69
1.3.11 Removing the Dual microSD 64GB Enterprise . . . . . . . . . 70
1.3.12 Removing the TPM and system board . . . . . . . . . . . . . 72
1.3.13 Removing the battery . . . . . . . . . . . . . . . . . . . . . . 76

Disassembly and Recycling Instructions CX400 M4
Contents

CX400 M4 Disassembly and Recycling Instructions 7
1 Disassembly and recycling
1.1 Recycling information
This manual provides instructions to disassembly the PRIMERGY CX400 M4
Server Enclosure and the PRIMERGY CX25x0 M4/M5 Server Nodes. All
materials can be disposed according to the regulation in the EU Directive
2012/19 / EU (Waste Electrical and Electronic Equipment (WEEE)).
Product group: Server
Model:
PRIMERGY CX400 M4 Server Enclosure and CX25x0 M4/M5 Server Nodes
Materials that must be disposed of separately
Description Part Number
Circuit boards
With a surface larger than 10 cm2
System board (on server node)
Midplane
Chassis interface board
HDD/SSD bridge board
Expansion cards (on server
node)
Power supply unit
1 - 4
1
1
1
several
1-2
Batteries Lithium battery CR2450 (on
server node)
1-4
Mercury-containing components
Liquid crystal displays (optionally
together with the housing) with a surface
of more than 100 cm2 and backlit displays
with gas discharge lamps
Cathode ray tubes
PCB-containing capacitors
(PCB: polychlorinated biphenyls)
Electrolytic capacitors containing
substances of concern (height> 25 mm,
diameter:> 25 mm or proportionally
similar volume)
Power supply unit
External cables
Gas discharge lamps

8 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
Plastics containing brominated flame
retardants
Toner cartridges, liquid and pasty, and
color toner
Not included
Asbestos waste and components
containing asbestos
Components containing refractory
ceramic fibers
Components containing radioactive
substances
Components containing
Chlorofluorocarbons (CFC),
hydrochlorofluorocarbons (HCFC),
hydrofluorocarbons (HFC) or
hydrocarbons (HC)
Materials that must be disposed of separately
Description Part Number

CX400 M4 Disassembly and Recycling Instructions 9
Disassembly and recycling
1.2 Disassembly of the server enclosure
INot all components are installed in the server enclosure depending on
the configuration.
1.2.1 Removing server nodes from the server enclosure
IFor recycling parts of the server nodes, see section "Disassembly of the
server nodes" on page 30.
Removing the CX2550 M4/M5 or CX2560 M4/M5 server node
ÊRemove all external cables from the server enclosure and server nodes.
Tools: tool-less
Recycling parts
1x - 4x server nodes
External cables
ÊOnly necessary for CX2550 M4 and
CX2560 M4 server nodes: remove the
gasket of the lower server node.
ÊUndo the locking mechanism (1) of
the release lever and pull the server
node out of the bay (2).

10 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
Figure 1: Removing the CX2550 M4/M5 or CX2560 M4/M5 server node
VCAUTION
If the server node is difficult to pull out of the bay, push the server node
(1), and then pull the server node (4) while pushing the server node to
the left side (2, 3).
Removing the CX2570 M4/M5 server node
ÊRemove all external cables from the server enclosure and server nodes.
Figure 2: Removing the CX2570 M4/M5 server node (A)
ÊUndo the locking mechanism (1) of the release lever and pull the server
node out of the bay (2).

CX400 M4 Disassembly and Recycling Instructions 11
Disassembly and recycling
Figure 3: Removing the CX2570 M4/M5 server node (B)
VCAUTION
If the server node is difficult to pull out of the bay, push the server node
(1), and then pull the server node (4) while pushing the server node to
the left side (2, 3).
Removing server node dummy modules
Figure 4: Removing the server node dummy module
ÊUndo the locking mechanism (1) of the release lever and pull the server
node dummy module out of the bay (2).
ÊDisassembly the server nodes as described in section "Disassembly of the
server nodes" on page 30.

12 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
1.2.2 Removing the ID card and server cover
ID card
Figure 5: ID card
ÊRemove the ID card (1) from the server enclosure.
VCAUTION!
If it is difficult to pull out the ID card, pull out the ID card, follow the
instructions below.
Tools: Phillips PH2 / (+) No. 2 hexagonal cross SW5 / PZ2
Recycling parts
1x ID (identification) card, 3x server cover, 12x screws
Metal
Plastic
ÊUnlock the upper lock of the
ID card by tilting the ID card
and pulling it out.

CX400 M4 Disassembly and Recycling Instructions 13
Disassembly and recycling
Removing the fan cover
Figure 6: Removing the fan cover from the chassis
ÊShift the locking tab in the direction of the arrow (1).
ÊFold up the fan cover (2) and remove it (3).
ÊUnlock the lower lock of the
ID card.

14 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
Removing the midplane cover 1
Figure 7: Removing the midplane cover 1 from the chassis
ÊRemove five screws from the midplane cover 1 (see circles)
ÊRemove the midplane cover.

CX400 M4 Disassembly and Recycling Instructions 15
Disassembly and recycling
Removing the midplane cover 2
Figure 8: Removing the midplane cover 2 from the chassis
ÊRemove seven screws from the midplane cover 2 (see circles)
ÊRemove the midplane cover.

16 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
1.2.3 Removing the hot-plug PSU
Removing the hot-plug PSU
Figure 9: Removing the hot-plug PSU
ÊRemove all hot-plug PSUs:
ÊPush the handle of the PSU halfway upward in the direction of the arrow
(1).
ÊPress in on the green locking latch (2).
ÊWhile keeping the green locking latch pressed, pull the PSU out of its bay
(3).
Tools: tool-less
Recycling parts
1x or 2x PSUs, 1x PSU dummy module
Metal
Plastic

CX400 M4 Disassembly and Recycling Instructions 17
Disassembly and recycling
Removing the PSU dummy module
Figure 10: Removing the PSU dummy module
ÊPress the handles of the PSU dummy module in the direction of the arrows
(1).
ÊPull the PSU dummy module out of the bay (2).
1.2.4 Removing fan modules
Tools: tool-less
Recycling parts
8x fan modules
Metal
Plastic
Cables

18 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
Figure 11: Disconnecting the fan cable
ÊDisconnect all fan cables:
ÊPull the fan cable out of the gaps next to the fans (1).
ÊDisconnect the fans from the fan cable (2).
ÊRemove all fan modules:
ÊRemove the fan module (see
arrow).

CX400 M4 Disassembly and Recycling Instructions 19
Disassembly and recycling
Figure 12: Disconnecting the fan cable from the midplane
ÊDisconnect all fan cables from the midplane (see circle).
1.2.5 Removing the fan cage
Figure 13: Removing the fan cage
ÊRemove four screws (see circles).
ÊLift the fan cage out of the server enclosure (1).
Tools: Phillips PH2 / (+) No. 2 screw driver
Recycling parts
1x fan cage, 4x screws
Metal

20 Disassembly and Recycling Instructions CX400 M4
Disassembly and recycling
1.2.6 Removing the midplane kit
Figure 14: Removing the midplane kit (A)
ÊDisconnect the front panel cables from the midplane (1).
ÊHang the cable ends on the housing edge to the outside.
ÊRemove two screws (see circles).
Tools: Phillips PH2 / (+) No. 2 hexagonal cross SW5 / PZ2
Recycling parts
1x PSU interposer, 1x chassis interface board, midplane, several screws
Metal
Plastic