Fujitsu PRIMERGY RX200 S5 User manual

PRIMERGY RX200 S5 Server
Options Guide
Edition April 2009

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]ujitsu.com.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4096-001.fm
Copyright © 2009 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

RX200 S5 Operating Manual
Contents
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 5
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 5
1.3 Expansions and conversions . . . . . . . . . . . . . . . . . . 7
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . . 9
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 13
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Pulling out/removing the server . . . . . . . . . . . . . . . . 19
4.2 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 20
4.3 Removing the air cowl . . . . . . . . . . . . . . . . . . . . . 22
5 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Installing a second processor . . . . . . . . . . . . . . . . . 23
5.2 Replacing the processor . . . . . . . . . . . . . . . . . . . . 26
5.3 Replacing the heat sink . . . . . . . . . . . . . . . . . . . . 29
6 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.2 Extending/replacing the main memory . . . . . . . . . . . . 34
7 Accessible drive . . . . . . . . . . . . . . . . . . . . . . . . 37

Operating Manual RX200 S5
Contents
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4112-001.fm
7.1 Installing a SATA DVD drive . . . . . . . . . . . . . . . . . . . 38
8 HDD modules . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9 Expansion cards and iBBU . . . . . . . . . . . . . . . . . . . 47
9.1 Installing an expansion card in riser cards . . . . . . . . . . 47
9.2 Installing a modular RAID controller . . . . . . . . . . . . . . 51
9.3 Installing an iBBU . . . . . . . . . . . . . . . . . . . . . . . . 52
10 USB solid state disk (uSSD) . . . . . . . . . . . . . . . . . . 57
11 Trusted Platform Module (TPM) . . . . . . . . . . . . . . . . . 59
12 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
12.1 Fitting the air cowl . . . . . . . . . . . . . . . . . . . . . . . . 61
12.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 65
13 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
13.1 Cabling overview . . . . . . . . . . . . . . . . . . . . . . . . 67
13.2 Cable diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 68
13.2.1 Cabling for up to 4 HDD modules . . . . . . . . . . . . . . . . 68
13.2.2 Cabling for up to 6 HDD modules . . . . . . . . . . . . . . . . . 69
13.2.3 Cabling for up to 8 HDD modules . . . . . . . . . . . . . . . . . 70
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

RX200 S5 Options Guide 5
1 Preface
The PRIMERGY RX200 S5 server is an Intel-based server for mid-size
networks and large companies. The server is suitable for use as a file server
and also as an application, information or Internet server.
Thanks to its highly developed hardware and software components, the
PRIMERGY RX200 S5 server offers a high level of data security and availability.
These components include hot-plug hard disk drive modules, redundant system
fans and power supply units, the Server Management ServerView Suite,
Prefailure Detection and Analysis (PDA) and Automatic Server Reconfiguration
and Restart (ASR&R).
Security functions in the BIOS Setup and on the system board protect the data
on the server against manipulation. Additional security is provided by the
lockable rack door.
The server occupies one height unit in the rack.
1.1 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
1.2 Documentation overview
More information on your PRIMERGY RX200 S5 can be found in the following
documents:
– “Quick Start Hardware - PRIMERGY RX200 S5” leaflet (only included as a
printed copy)
– “Quick Start Software - Quick Installation Guide” DVD booklet (only included
with the PRIMERGY ServerView Suite as a printed copy)
– “Safety notes and other important information” manual

6 Options Guide RX200 S5
Documentation overview Preface
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4098-001.fm
– “Warranty” manual
– “PRIMERGY ServerView Suite Local Service Concept - LSC” manual
– “Returning used devices” manual
– “Helpdesk” leaflet
– Technical manual for the system board D2786
– “PRIMERGY RX200 S5 Server Operating Manual”
– "D2786 BIOS Setup Utility for RX200 S5" manual
IPRIMERGY manuals are available in PDF format on the PRIMERGY
ServerView Suite DVD 2. The PRIMERGY ServerView Suite DVD 2 is
part of the PRIMERGY ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.
Further sources of information:
– PRIMERGY Abbreviations and Glossary on the PRIMERGY
ServerView Suite DVD 2
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system

RX200 S5 Options Guide 7
Preface Expansions and conversions
1.3 Expansions and conversions
Second processor
The system board can be upgraded with a second processor. Only processors
of the same type may be used on the system board. The second processor must
have the same clock frequency as the first.
Main memory expansion
The system board supports up to 96 GB of main memory. 6 slots (2 banks with
3 channels each) are provided for each CPU for the main memory.
Accessible drive
In the version with a maximum of six HDD modules, a 5.25 inch bay is available
for a DVD drive (SATA interface) with a height of 0.5 inches.
Extending the number of HDD modules
You can add further HDD modules, if required. The server can accommodate a
maximum of eight HDD modules. To do this, you may need to exchange the
HDD backplane.
Expansion cards in the PCI slots
The system board offers two slots with a PCI Express x8 interface and one slot
with a PCI Express x4 interface (exclusively for modular RAID controllers):
Expansion cards can only be installed using three-slot riser cards. The riser
cards provide three slots at a right angle to the system board (two slots for PCIe
controllers and one slot for a RAID controller).
Intelligent Battery Backup Unit
You can add an iBBU (intelligent Battery Backup Unit) to the optional modular
RAID controller to ensure data integrity in the event of a power failure.
uSSD
You can insert a USB solid state disk on the system board at a later time.

8 Options Guide RX200 S5
Expansions and conversions Preface
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4098-001.fm
TPM
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
Fujitsu Technology Solutions BIOS manual).
VCAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.

RX200 S5 Options Guide 9
Preface Notational conventions
1.4 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
“Quotation marks” indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.

© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4098-001.fm

RX200 S5 Options Guide 11
2Procedure
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS failures must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.
ÊFirst of all, carefully read the safety instructions in the chapter “Safety
instructions” on page 13 et seq..
ÊMake sure that all necessary manuals (see the section “Documentation
overview” on page 5) are available; print the PDF files if required. Most
importantly, you will need the operating manual for the server and the
technical manual for the system board.
ÊShut the server down correctly, switch it off, disconnect the power plugs and
open the server as described in the chapter “Preparation” on page 19 et
seq..
ÊCarry out the expansion or upgrade of your server as described in the
pertinent chapter.
IInstallation and removal of the hot-plug components are described in
the operating manual.
ÊClose the server, connect it to the power outlet, and switch it on as described
in the chapter “Completion” on page 61 et seq..
ÊStart the operating system and make the appropriate configuration if
necessary (see the operating manual).

© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4099-001.fm

RX200 S5 Options Guide 13
3 Safety instructions
IThe following safety instructions are also provided in the manual “Safety
notes and other important information”.
This device meets the relevant safety regulations for IT equipment. If you have
any questions about whether you can install the server in the intended
environment, please contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS failures must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any failure to observe the guidelines in this manual, and any improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) or damage the equipment.

14 Options Guide RX200 S5
Safety instructions
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4100-001.fm
Before starting up
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the device.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●This unit should not be operated in ambient temperatures above
35 °C.
●If the unit is integrated into an installation that draws power from an
industrial power supply network with an IEC309 connector, the power
supply's fuse protection must comply with the requirements for non-
industrial power supply networks for type A connectors.
●The unit automatically adjusts itself to a mains voltage in a range of
100 V - 127 V oder 200 V - 240 V. Ensure that the local mains
voltage lies within these limits.
●This device must only be connected to properly grounded shock-
proof sockets or insulated sockets of the rack's internal power supply
with tested and approved power cables.
●Ensure that the device is connected to a grounded shockproof socket
close to the device.

RX200 S5 Options Guide 15
Safety instructions
VCAUTION!
●Ensure that the power sockets on the device and the grounded shock-
proof sockets are freely accessible.
●The On/Off button or the main power switch (if present) does not
isolate the device from the mains power supply. To disconnect it
completely from the mains power supply, unplug all network power
plugs from the grounded shockproof sockets.
●Always connect the server and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the server is still running but a peripheral device (e.g. memory
subsystem) fails during a power outage.
●Data cables must be adequately shielded.
●The EN 50173 and EN 50174-1/2 standards apply for LAN cabling.
The minimum requirement is the use of a category 5 screened LAN
cable for 10/100 Mbit/s Ethernet, or a category 5e cable for Gigabit
Ethernet. The requirements from the ISO/IEC 11801 specification
must also be met.
●Route the cables in such a way that they do not create a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting the server, refer to the relevant
instructions in this manual.
●Never connect or disconnect data transmission lines during a storm
(risk of lightning strike).
●Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can
get inside the server (risk of electric shock, short circuit).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign bodies), switch off the server immediately, remove
all power plugs and contact your sales outlet or customer service
team.

16 Options Guide RX200 S5
Safety instructions
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4100-001.fm
VCAUTION!
●Proper operation of the system (in accordance with IEC 60950-1/
EN 60950-1) is only ensured if the casing is completely assembled
and the rear covers for the installation slots have been fitted (electric
shock, cooling, fire protection, interference suppression).
●Only install system expansions that satisfy the requirements and
rules governing safety and electromagnetic compatibility and those
relating to telecommunication terminals. If you install other expan-
sions, they may damage the system or violate the safety regulations.
Information on which system expansions are approved for installation
can be obtained from our customer service center or your sales
outlet.
●The components marked with a warning notice (e.g. lightning symbol)
may only be opened, removed or exchanged by authorized, qualified
personnel. Exception: CCS components can be replaced.
●The warranty is void if the server is damaged during installation or
replacement of system expansions.
●Only set screen resolutions and refresh rates that are specified in the
operating manual for the monitor. Otherwise, you may damage your
monitor. If you are in any doubt, contact your sales outlet or customer
service center.
Batteries
VCAUTION!
●Incorrect replacement of batteries may result in a risk of explosion.
The batteries may only be replaced with identical batteries or with a
type recommended by the manufacturer (see the technical manual for
the system board).
●Replace the lithium-battery on the system board in accordance with
the instructions in the technical manual for the system board.

RX200 S5 Options Guide 17
Safety instructions
Working with CDs/DVDs and CD/DVD drives
When working with devices with CD/DVD drives, these instructions must be
followed.
VCAUTION!
●Only use CDs/DVDs that are in perfect condition in your server's
CD/DVD drive, in order to prevent data loss, equipment damage and
injury.
●Check each CD/DVD for damage, cracks, breakages etc. before
inserting it in the drive.
Note that any additional labels applied may change the mechanical
properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain circumstances, sharp CD/DVD fragments can pierce
the cover of the CD/DVD drive (equipment damage) and can fly out
of the device (danger of injury, particularly to uncovered body parts
such as the face or neck).
IYou can prevent mechanical damage and damage to the CD/DVD drive,
as well as premature CD/DVD wear, by observing the following sugges-
tions:
– Only insert CDs/DVDs in the drive when needed and remove them
after use.
– Store the CDs/DVDs in suitable sleeves.
– Protect the CDs/DVDs from exposure to heat and direct sunlight.
Laser information
The CD/DVD drive complies with IEC 60825-1 laser class 1.
VCAUTION!
The CD/DVD drive contains a light-emitting diode (LED), which under
certain circumstances produces a laser beam stronger than laser
class 1. Looking directly at this beam is dangerous.
Never remove parts of the CD/DVD drive casing!

18 Options Guide RX200 S5
Safety instructions
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4100-001.fm
Modules with electrostatic-sensitive components
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug before installing or removing components
containing ESDs.
●You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●The equipment and tools you use must be free of static charges.
●Only touch the components at the positions highlighted in green (touch
points).
●Do not touch any exposed pins or conductors on a component.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in the
relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).

RX200 S5 Options Guide 19
4 Preparation
VCAUTION!
Follow the safety instructions in the chapter “Safety instructions” on
page 13.
4.1 Pulling out/removing the server
ÊTerminate all applications and shut down the server correctly.
ÊIf your operating system has not switched off the server, press the on/off
button.
ÊPull all power connectors out of the power outlets.
ÊLoosen the knurled screws on the sides and pull the server carefully out of
the rack as far as it will go.
IIf the server is not easily accessible once it has been pulled out,
remove it from the rack completely. See the operating manual for
details on how to remove the server from the rack.
VCAUTION!
At least two people are needed to remove the server from the rack.

20 Options Guide RX200 S5
Opening the server Preparation
© cognitas. Gesellschft für Technik-Dokumentation mbH 2009 Pfad: W:\Anwendungsdaten\FCT\tim_local\work\PICHOL\OBJ_DOKU-4101-001.fm
4.2 Opening the server
You must remove the fan cover before removing the housing cover.
Removing the fan cover
Figure 2: Opening the fan cover
ÊPush the two green buttons (1) in the direction of the arrow and lift the fan
cover upwards to remove it (2).
Removing the housing cover
Figure 3: Removing the housing cover
ÊUse the two green locking levers (see circles) to unlock the housing cover.
1
1
2