Fujitsu ETERNUS DX60 S3 User manual

FUJITSU Storage
ETERNUS DX60 S4,
ETERNUS DX60 S3
Hybrid Storage Systems
Operation Guide (Basic)
Operation management/maintenance
P3AM-9012-08ENZ0

Table of Contents
1. Component Names and LED Names 9
Controller Enclosures ...................................................................................................................... 9
Front .......................................................................................................................................................................9
Rear ......................................................................................................................................................................10
Components (Front) .............................................................................................................................................11
ETERNUS DX60 S4 Components (Rear) ..................................................................................................................14
ETERNUS DX60 S3 Components (Rear) ..................................................................................................................17
Drive Enclosures ........................................................................................................................... 22
Front .....................................................................................................................................................................22
Rear ......................................................................................................................................................................23
Components (Front)..............................................................................................................................................24
Components (Rear) ..............................................................................................................................................26
Power Distribution Units (for Regions other than the EMEIA, Central American, and Caribbean Re-
gions) ........................................................................................................................................... 29
Power Distribution Units (1U) ...............................................................................................................................29
Power Distribution Units (2U) ...............................................................................................................................30
2. Basic Operation 32
Powering On and Off..................................................................................................................... 32
Switching On and Off the Main Line Switch on the Power Distribution Unit (for Regions other than the EMEIA,
Central American, and Caribbean Regions)...........................................................................................................32
Switching On and Off the PSU Switch on the Power Supply Unit............................................................................36
Powering On .........................................................................................................................................................38
Powering Off .........................................................................................................................................................39
Using the FUNCTION Button.......................................................................................................... 41
3. Storage System Monitoring 43
Checking LED Status...................................................................................................................... 43
Displaying Status via ETERNUS Web GUI ....................................................................................... 43
Displaying Status via ETERNUS CLI ................................................................................................ 44
Event Notification ......................................................................................................................... 44
Audit Log ...................................................................................................................................... 45
2
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

4. Component Expansion/Function Enhancement 47
Installing Additional Drives........................................................................................................... 47
Installable Drives ..................................................................................................................................................47
Drive Handling Instructions...................................................................................................................................47
Additional Drive Installation Procedure.................................................................................................................48
Installing Additional Drive Enclosures........................................................................................... 54
Installable Drive Enclosures ..................................................................................................................................54
Drive Enclosure Handling Instructions...................................................................................................................54
Additional Drive Enclosure Installation Procedure.................................................................................................56
Adding Servers.............................................................................................................................. 69
RAID Group Creation..............................................................................................................................................69
Volume Creation ...................................................................................................................................................70
Connection Setup ..................................................................................................................................................71
5. Maintenance 76
Periodic Backup ............................................................................................................................ 76
Maintenance Service..................................................................................................................... 76
Maintenance Support Period.................................................................................................................................76
Replacing Batteries ...............................................................................................................................................76
Related Service......................................................................................................................................................77
6. Troubleshooting 78
Check List...................................................................................................................................... 78
Required Information for Inquiries................................................................................................ 86
Table of Contents
3
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

List of Figures
Figure 1 Front View of a 2.5" Type Controller Enclosure............................................................................................9
Figure 2 Front View of a 3.5" Type Controller Enclosure............................................................................................9
Figure 3 Rear View of a Controller Enclosure (When Only One Controller Is Installed)............................................10
Figure 4 Rear View of a Controller Enclosure (When Two Controllers Are Installed)................................................10
Figure 5 Operation Panel (Controller Enclosure) ....................................................................................................11
Figure 6 2.5" Drives................................................................................................................................................13
Figure 7 Drive Slot Numbers (2.5" Type Controller Enclosure) ................................................................................13
Figure 8 3.5" Drives................................................................................................................................................13
Figure 9 Drive Slot Numbers (3.5" Type Controller Enclosure) ................................................................................13
Figure 10 Controllers................................................................................................................................................14
Figure 11 Power Supply Unit (Controller Enclosure).................................................................................................17
Figure 12 Controllers................................................................................................................................................18
Figure 13 Power Supply Unit (Controller Enclosure).................................................................................................21
Figure 14 Front View of a 2.5" Type Drive Enclosure.................................................................................................22
Figure 15 Front View of a 3.5" Type Drive Enclosure.................................................................................................22
Figure 16 Rear View of a Drive Enclosure (When Only One I/O Module Is Installed) .................................................23
Figure 17 Rear View of a Drive Enclosure (When Two I/O Modules Are Installed).....................................................23
Figure 18 Operation Panel (Drive Enclosure) ...........................................................................................................24
Figure 19 2.5" Drives................................................................................................................................................25
Figure 20 Drive Slot Numbers (2.5" Type Drive Enclosure) .......................................................................................25
Figure 21 3.5" Drives................................................................................................................................................25
Figure 22 Drive Slot Numbers (3.5" Type Drive Enclosure) .......................................................................................25
Figure 23 I/O Module ...............................................................................................................................................26
Figure 24 Power Supply Unit (Drive Enclosure) ........................................................................................................28
Figure 25 Power Distribution Unit (AC200-240V, 1U, 4 Outlets)...............................................................................29
Figure 26 Power Distribution Unit (AC200-240V, 1U, 4 Outlets)...............................................................................29
Figure 27 Power Distribution Unit (AC200-240V, 2U, 12 Outlets).............................................................................30
Figure 28 Power Distribution Unit (AC200-240V, 2U, 16 Outlets).............................................................................30
Figure 29 Power Distribution Unit (AC200-240V, 2U, 16 Outlets).............................................................................31
Figure 30 ON Position (Marked "|") of the Main Line Switches on a 1U Power Distribution Unit ..............................32
Figure 31 ON Position of the Main Line Switches on a 1U Power Distribution Unit ..................................................32
Figure 32 ON Position (Marked "|") of the Main Line Switches on a 2U Power Distribution Unit ..............................33
Figure 33 ON Position of the Main Line Switches on a 2U Power Distribution Unit ..................................................33
Figure 34 OFF Position (Marked "¡") of the Main Line Switches on a 1U Power Distribution Unit ...........................34
Figure 35 OFF Position of the Main Line Switches on a 1U Power Distribution Unit .................................................34
Figure 36 OFF Position (Marked "¡") of the Main Line Switches on a 2U Power Distribution Unit ...........................35
Figure 37 OFF Position of the Main Line Switches on a 2U Power Distribution Unit .................................................35
Figure 38 ON Position (Marked "|") of the PSU Switch on a Power Supply Unit ........................................................36
Figure 39 OFF Position (Marked "¡") of the PSU Switch of a Power Supply Unit ......................................................37
Figure 40 ETERNUS Web GUI Screen.........................................................................................................................43
Figure 41 Event Notification ....................................................................................................................................45
Figure 42 Audit Log..................................................................................................................................................46
4
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

List of Tables
Table 1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure)) ............................................11
Table 2 Status and Meanings of Each LED (Drive (Controller Enclosure)) .............................................................14
Table 3 Status and Meanings of Each LED (Controller) .........................................................................................16
Table 4 Status and Meanings of Each LED (Power Supply Unit (Controller Enclosure)).........................................17
Table 5 Status and Meanings of Each LED (Controller) .........................................................................................19
Table 6 Status and Meanings of Each LED (Power Supply Unit (Controller Enclosure)).........................................21
Table 7 Status and Meanings of Each LED (Operation Panel (Drive Enclosure)) ...................................................24
Table 8 Status and Meanings of Each LED (Drive (Drive Enclosure)).....................................................................26
Table 9 Status and Meanings of Each LED (I/O Module) .......................................................................................26
Table 10 Status and Meanings of Each LED (Power Supply Unit (Drive Enclosure)) ................................................28
Table 11 General Status of ETERNUS Web GUI.........................................................................................................43
Table 12 General Status of ETERNUS CLI .................................................................................................................44
5
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Preface
Fujitsu would like to thank you for purchasing the FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 (herein-
after referred to as ETERNUS DX).
The ETERNUS DX is designed to be connected to Fujitsu servers (Fujitsu SPARC Servers, PRIMEQUEST, or PRIMER-
GY) or non-Fujitsu servers.
This manual describes the operation management and maintenance of the ETERNUS DX.
This manual is intended for use of the ETERNUS DX in regions other than Japan.
Please carefully review the information outlined in this manual.
Eighth Edition
April 2018
6
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Trademarks
Third-party trademark information related to this product is available at:
http://www.fujitsu.com/global/products/computing/storage/eternus/trademarks.html
About This Manual
Intended Audience
This manual is intended for storage system administrators or system administrators who manage and maintain
the ETERNUS DX.
Related Information and Documents
The latest version of this manual and the latest information for your model are available at:
http://www.fujitsu.com/global/support/products/computing/storage/disk/manuals/
Refer to the following manuals of your model as necessary:
"Configuration Guide -Server Connection-"
"Configuration Guide (Power Synchronized Unit)"
Document Conventions
■Third-Party Product Names
•Oracle Solaris may be referred to as "Solaris", "Solaris Operating System", or "Solaris OS".
•Microsoft® Windows Server® may be referred to as "Windows Server".
■Notice Symbols
The following notice symbols are used in this manual:
Indicates information that you need to observe when using the ETERNUS storage system.
Make sure to read the information.
Indicates information and suggestions that supplement the descriptions included in this
manual.
Preface
7
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Warning Signs
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material damage.
These signs are composed of a symbol and a message describing the recommended level of caution. The follow-
ing explains the symbol, its level of caution, and its meaning as used in this manual.
This symbol indicates the possibility of serious or fatal injury if the ETERNUS DX is not used
properly.
This symbol indicates the possibility of minor or moderate personal injury, as well as dam-
age to the ETERNUS DX and/or to other users and their property, if the ETERNUS DX is not
used properly.
This symbol indicates IMPORTANT information for the user to note when using the ETERNUS
DX.
The following symbols are used to indicate the type of warnings or cautions being described.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION contents. Inside the
triangle and above it are details concerning the symbol (e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action which must be
avoided is both illustrated inside the barred circle and written above it (e.g. No Disassem-
bly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The required action is
both illustrated inside the black disk and written above it (e.g. Unplug).
How Warnings are Presented in This Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical rib-
bon in the left margin, to distinguish this warning from ordinary descriptions.
A display example is shown here.
Warning level indicator
Warning type indicator
Warning details
•To avoid damaging the ETERNUS storage system, pay attention to the
following points when cleaning the ETERNUS storage system:
Warning layout ribbon
Example warning
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS storage system
when using cleaners, etc.
- Do not use alcohol or other solvents to clean the ETERNUS storage system.
CAUTION Do
Preface
8
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

1. Component Names and LED Names
This chapter provides the component names of the ETERNUS DX.
Controller Enclosures
An operation panel and drives are installed in the front of the controller enclosure. Controllers and power supply
units are installed in the rear.
Note that some LED names of the controllers are different in the ETERNUS DX60 S4 and the ETERNUS DX60 S3.
Front
This section provides the names of the components on the front of a controller enclosure.
■2.5" Type
Figure 1 Front View of a 2.5" Type Controller Enclosure
1
3 3
2
1. Operation panel
2. 2.5" drive
3. Flange cover
■3.5" Type
Figure 2 Front View of a 3.5" Type Controller Enclosure
1
3 3
2
1. Operation panel
2. 3.5" drive
3. Flange cover
9
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Rear
This section provides the names of the components on the rear of a controller enclosure.
■When Only One Controller Is Installed
Figure 3 Rear View of a Controller Enclosure (When Only One Controller Is Installed)
12
34
1. Controller (CM#0)
2. Cover
Remove this when installing an additional controller (optional).
3. Power supply unit (PSU#0)
4. Power supply unit (PSU#1)
■When Two Controllers Are Installed
Figure 4 Rear View of a Controller Enclosure (When Two Controllers Are Installed)
12
34
1. Controller (CM#0)
2. Controller (CM#1)
3. Power supply unit (PSU#0)
4. Power supply unit (PSU#1)
1. Component Names and LED Names
Controller Enclosures
10
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Components (Front)
This section describes the operation panel and the drives in the front of the controller enclosure.
■Operation Panel
An operation panel has LEDs, a Power switch, and a FUNCTION button.
Figure 5 shows the operation panel. Table 1 shows the status and meanings of each LED.
Figure 5 Operation Panel (Controller Enclosure)
2
3
1
4
56
7
2
3
1
4
56
78
AB
A. With a flange cover
B. Without a flange cover
1. Power switch
This switch is used to turn on or off the ETERNUS DX.
2. POWER LED
3. IDENTIFY LED
4. FAULT LED
5. MAINTENANCE LED
6. CACHE LED
7. READY LED
8. FUNCTION button
This button is used to switch the maintenance status on or off, to switch the master CM (when two controllers
are mounted), to initialize the LAN ports, or to initialize the user settings.
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure))
LED name LED status Meaning
POWER
(green)
DC power is supplied to the controller enclosure.
IDENTIFY (blinks blue) The installation location of the controller enclosure is identified
according to the instruction that is issued from ETERNUS Web GUI
or ETERNUS CLI.
1. Component Names and LED Names
Controller Enclosures
11
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

LED name LED status Meaning
FAULT (amber) The ETERNUS DX is in error status.
(blinks amber)
A part of the ETERNUS DX requires preventive maintenance.
MAINTENANCE
(green)
Maintenance for the ETERNUS DX is in progress.
(blinks green)
Maintenance (from ETERNUS Web GUI or ETERNUS CLI) for the
ETERNUS DX is in progress or a status check of the ETERNUS DX is
necessary.
CACHE (green) There is data in the cache memory of the ETERNUS DX.
READY
(green)
The ETERNUS DX is available for use.
1. Component Names and LED Names
Controller Enclosures
12
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

■Drives
●2.5" Drives
Figure 6 shows the 2.5" drive. Figure 7 shows the slot number of each 2.5" drive.
Table 2 shows the status and meanings of each LED.
Figure 6 2.5" Drives
12
1. DRIVE READY LED
2. DRIVE FAULT LED
Figure 7 Drive Slot Numbers (2.5" Type Controller Enclosure)
Slot#8 Slot#9
Slot#10 Slot#11 Slot#12 Slot#13 Slot#14 Slot#15
Slot#0 Slot#1 Slot#2 Slot#3 Slot#4 Slot#5 Slot#6 Slot#7
Slot#16 Slot#17 Slot#18 Slot#19 Slot#20 Slot#21 Slot#22 Slot#23
●3.5" Drives
Figure 8 shows the 3.5" drive. Figure 9 shows the slot number of each 3.5" drive.
Table 2 shows the status and meanings of each LED.
Figure 8 3.5" Drives
1
2
1. DRIVE READY LED
2. DRIVE FAULT LED
Figure 9 Drive Slot Numbers (3.5" Type Controller Enclosure)
Slot#0
Slot#4
Slot#8
Slot#1
Slot#5
Slot#9
Slot#2
Slot#6
Slot#10
Slot#3
Slot#7
Slot#11
1. Component Names and LED Names
Controller Enclosures
13
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

The LEDs turn on or blink to indicate the statuses that are listed below.
Table 2 Status and Meanings of Each LED (Drive (Controller Enclosure))
LED name LED status Meaning
DRIVE READY (green) The drive is in normal status.
(blinks green)
DRIVE FAULT (amber)
•The drive is in error status.
•The LED light up operation was performed from the ETERNUS
CLI command line in order to identify the drive location.
ETERNUS DX60 S4 Components (Rear)
This section describes the controllers and the power supply units in the rear of the controller enclosure for the
ETERNUS DX60 S4.
■Controllers
The controller contains a CPU, system memory, Battery Backup Unit (BBU), host interfaces, drive interface (DI)
ports, and LAN ports. The controller controls all operations in the ETERNUS DX.
Controllers (FC, iSCSI 10Gbit/s, iSCSI 1Gbit/s, SAS 12Gbit/s, and SAS 6Gbit/s) are available for different types of
host interfaces.
Figure 10 shows the controller. Table 3 shows the status and meanings of each LED.
Figure 10 Controllers
1234 5
1614 15
17
16
17
18 22 23
SAS 6Gbit/s SAS 12Gbit/s
FC iSCSI 1Gbit/s iSCSI 10Gbit/s
6810711
12 13
9
19 19 19 19 19 19
2020
2121
89
20
21
20
21
1. PWC port
This port is used to connect a power synchronization unit with an RS232C cable.
1. Component Names and LED Names
Controller Enclosures
14
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

2. DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a mini SAS HD cable between enclo-
sures.
3. RMT (LAN) port
This port is used for connecting a LAN cable and used for the remote support function. This port uses an RJ-45
connector.
4. MNT (LAN) port
This port is used for connecting a LAN cable and used for operation management. This port uses an RJ-45 con-
nector.
5. Host interface (CA#0)
This interface is used for connecting a controller with a server.
6. Host interface port (FC port) (CA#0, Port#0)
This port is used for connecting a controller to a server with an FC cable. This port uses a Dual LC connector.
7. Host interface port (FC port) (CA#0, Port#1)
This port is used for connecting a controller to a server with an FC cable. This port uses a Dual LC connector.
8. Host interface port (iSCSI port) (CA#0, Port#0)
This port is used for connecting a LAN cable. This port uses an RJ-45 connector.
9. Host interface port (iSCSI port) (CA#0, Port#1)
This port is used for connecting a LAN cable. This port uses an RJ-45 connector.
10. Host interface port (SAS port) (CA#0, Port#0)
This port is used for connecting an SAS cable. This port uses a miniSAS (SFF-8088) connector.
11. Host interface port (SAS port) (CA#0, Port#1)
This port is used for connecting an SAS cable. This port uses a miniSAS (SFF-8088) connector.
12. Host interface port (SAS port) (CA#0, Port#0)
This port is used for connecting an SAS cable. This port uses a miniSAS HD (SFF-8644) connector.
13. Host interface port (SAS port) (CA#0, Port#1)
This port is used for connecting an SAS cable. This port uses a miniSAS HD (SFF-8644) connector.
14. IDENTIFY/BBU FAULT LED
15. DI (OUT) LINK/FAULT LED
16. LAN ACT LED
17. LAN LINK LED
18. READY/FAULT LED
19. LINK/FAULT LED
20. FAULT LED
21. LINK LED
22. CA#0 FAULT LED
23. MASTER LED
1. Component Names and LED Names
Controller Enclosures
15
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

The LEDs turn on or blink to indicate the statuses that are listed below.
Table 3 Status and Meanings of Each LED (Controller)
LED name LED status Meaning
IDENTIFY/BBU FAULT
(blinks blue)
As ordered via ETERNUS Web GUI or ETERNUS CLI, the installation
location of the controller is identified.
(amber) The battery is in error status.
DI (OUT) LINK/FAULT (green) The link between the DI (OUT) port and the destination port has
been established.
(amber)
•The link between the DI (OUT) port and the destination port is
in error status.
•The ports to remove the cables between enclosures from are in-
dicated. This occurs while a drive enclosure is being added.
(blinks amber)
The ports to connect the cables are indicated. This occurs while a
drive enclosure is being added.
LAN ACT
(blinks green)
Data is being sent or received via the LAN port.
LAN LINK (green) The link between the LAN port and the destination has been es-
tablished.
READY/FAULT (green) The controller is in normal status.
(blinks green)
An error has occurred during startup.
(amber)
•The controller is performing the initial setup after the power is
turned on.
•The controller is in error status.
(blinks amber)
LINK/FAULT (green) The link between the host interface port (FC or SAS) and the des-
tination port has been established.
(amber) The host interface port (FC or SAS) is in error status.
FAULT (green) The link between the host interface port (iSCSI) and the destina-
tion port has been established.
LINK (amber) The host interface port (iSCSI) is in error status.
CA FAULT (amber) The host interface is in error status.
MASTER (green) The controller is set as a Master CM.
1. Component Names and LED Names
Controller Enclosures
16
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

■Power Supply Units
The power supply unit transforms input AC power from a power socket to DC power and supplies power to each
component.
Each power supply unit contains fans.
Figure 11 shows the power supply unit. Table 4 shows the status and meanings of each LED.
Figure 11 Power Supply Unit (Controller Enclosure)
1234 5 6
1. POWER LED
2. FAULT LED
3. AC MISSING LED
4. FAN FAIL LED
5. PSU switch
This switch is used to turn on and off the AC power supply.
6. Inlet
This inlet is used to connect a power cord.
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 4 Status and Meanings of Each LED (Power Supply Unit (Controller Enclosure))
LED name LED status Meaning
POWER (green) AC power is supplied to the power supply unit.
(blinks green)
AC power is supplied to the power supply unit, but DC power is
not supplied to the ETERNUS DX.
FAULT (amber) AC power is not supplied to the power supply unit.
AC MISSING (amber) AC power is not supplied to this power supply unit, but AC power
is supplied to the other power supply unit.
FAN FAIL (amber) The power supply unit or the fan in the power supply unit is in er-
ror status.
ETERNUS DX60 S3 Components (Rear)
This section describes the controllers and the power supply units in the rear of the controller enclosure for the
ETERNUS DX60 S3.
■Controllers
The controller contains a CPU, cache memory, System Capacitor Unit (SCU), host interfaces, drive interface (DI)
ports, and LAN ports. The controller controls all operations in the ETERNUS DX.
1. Component Names and LED Names
Controller Enclosures
17
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

Controllers (FC, iSCSI 10Gbit/s, iSCSI 1Gbit/s, and SAS) are available for different types of host interfaces.
Figure 12 shows the controller. Table 5 shows the status and meanings of each LED.
Figure 12 Controllers
1234 5
1412 13
15
14
15
16 20 21
SAS
FC iSCSI 1Gbit/s iSCSI 10Gbit/s
6810711
9
17 17 17 17
1818
1919
89
18
19
18
19
1. PWC port
This port is used to connect a power synchronization unit with an RS232C cable.
2. DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a mini SAS HD cable between enclo-
sures.
3. RMT (LAN) port
This port is used for connecting a LAN cable and used for the remote support function. This port uses an RJ-45
connector.
4. MNT (LAN) port
This port is used for connecting a LAN cable and used for operation management. This port uses an RJ-45 con-
nector.
5. Host interface (CA#0)
This interface is used for connecting a controller with a server.
6. Host interface port (FC port) (CA#0, Port#0)
This port is used for connecting a controller to a server with an FC cable. This port uses a Dual LC connector.
7. Host interface port (FC port) (CA#0, Port#1)
This port is used for connecting a controller to a server with an FC cable. This port uses a Dual LC connector.
8. Host interface port (iSCSI port) (CA#0, Port#0)
This port is used for connecting a LAN cable. This port uses an RJ-45 connector.
9. Host interface port (iSCSI port) (CA#0, Port#1)
This port is used for connecting a LAN cable. This port uses an RJ-45 connector.
1. Component Names and LED Names
Controller Enclosures
18
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

10. Host interface port (SAS port) (CA#0, Port#0)
This port is used for connecting an SAS cable. This port uses a miniSAS (SFF-8088) connector.
11. Host interface port (SAS port) (CA#0, Port#1)
This port is used for connecting an SAS cable. This port uses a miniSAS (SFF-8088) connector.
12. IDENTIFY/SCU READY LED
13. DI (OUT) LINK/FAULT LED
14. LAN ACT LED
15. LAN LINK LED
16. READY/FAULT LED
17. LINK/FAULT LED
18. FAULT LED
19. LINK LED
20. CA#0 FAULT LED
21. MASTER LED
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 5 Status and Meanings of Each LED (Controller)
LED name LED status Meaning
IDENTIFY/SCU READY
(blinks blue)
As ordered via ETERNUS Web GUI or ETERNUS CLI, the installation
location of the controller is identified.
(blinks green)
System Capacitor Unit (SCU) is charging.
DI (OUT) LINK/FAULT (green) The link between the DI (OUT) port and the destination port has
been established.
(amber)
•The link between the DI (OUT) port and the destination port is
in error status.
•The ports to remove the mini SAS HD cables between enclo-
sures from are indicated. This occurs while a drive enclosure is
being added.
(blinks amber)
The ports to connect the cables are indicated. This occurs while a
drive enclosure is being added.
LAN ACT
(blinks green)
Data is being sent or received via the LAN port.
LAN LINK (green) The link between the LAN port and the destination has been es-
tablished.
READY/FAULT (green) The controller is in normal status.
(blinks green)
An error has occurred during startup.
(amber)
•The controller is performing the initial setup after the power is
turned on.
•The controller is in error status.
(blinks amber)
LINK/FAULT (green) The link between the host interface port (FC or SAS) and the des-
tination port has been established.
(amber) The host interface port (FC or SAS) is in error status.
1. Component Names and LED Names
Controller Enclosures
19
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0

LED name LED status Meaning
FAULT (green) The link between the host interface port (iSCSI) and the destina-
tion port has been established.
LINK (amber) The host interface port (iSCSI) is in error status.
CA FAULT (amber) The host interface is in error status.
MASTER (green) The controller is set as a Master CM.
1. Component Names and LED Names
Controller Enclosures
20
FUJITSU Storage ETERNUS DX60 S4, ETERNUS DX60 S3 Hybrid Storage Systems Operation Guide (Basic)
Copyright 2018 FUJITSU LIMITED
P3AM-9012-08ENZ0