Funkwerk EGO LOOK User manual

Operating Manual
130 8001 1.07
US
English

EGO LOOK
Funkwerk Dabendorf reserves the right to modifi cations in the course of technological progress and deviations from the deli-
very scope! All rights reserved! Reproduction, in whole or in part, is only permitted with the prior written consent of Funkwerk
Dabendorf GmbH!

2 |3
Table of Contents
3 Introduction / foreword ................................................................................................. 7
4 Safety notes................................................................................................................... 8
5 Scope of delivery / package content.............................................................................. 9
6 Installation instructions ................................................................................................ 10
6.1 Required configuration.................................................................................................................................10
6.1.1 Vehicle ................................................................................................................................................................................ 10
6.1.2 Mobile phone...................................................................................................................................................................... 10
6.1.3 Muting (radio mute switch)................................................................................................................................................ 10
6.1.4 Converting the EGO LOOK into a previously installed Funkwerk hands-free car kit..................................................... 10
6.1.5 Add-on speakers / Car audio telephone connection........................................................................................................ 10
6.1.6 Car radio line-in................................................................................................................................................................. 11
6.2 Installation locations....................................................................................................................................11
6.2.1 Checking cable lengths ..................................................................................................................................................... 11
6.2.2 Selection of site for installing the electronics box........................................................................................................... 11
6.2.3 Selection of site for installing the microphone ................................................................................................................ 12
6.2.4 Selection of site for installing the radio controller.......................................................................................................... 13
6.2.5 Selection of site for installing the display ........................................................................................................................ 13
6.3 Installation....................................................................................................................................................14
6.3.1 Mounting the electronics box ............................................................................................................................................ 14
6.3.2 Mounting the microphone.................................................................................................................................................. 14
6.3.3 Inserting the battery in the radio controller..................................................................................................................... 15
6.3.4 Mounting the radio controller ........................................................................................................................................... 15
6.3.5 Mounting the display.......................................................................................................................................................... 15
6.4 Connection scheme ......................................................................................................................................16
6.4.1 Preface ............................................................................................................................................................................... 16
6.4.2 EGO mute cable.................................................................................................................................................................. 17

EGO LOOK
6.5 Installing the ISO connection cable..............................................................................................................18
6.5.1 Checking the mute inputs / ISO-Profi............................................................................................................................... 18
6.5.2 Checking the installation................................................................................................................................................... 21
6.5.3 Additional external speakers ............................................................................................................................................ 21
6.6 Connecting the components to the electronics box.....................................................................................22
6.7 Connecting the EGO iDapter to the electronics box.....................................................................................24
7 Operating instructions................................................................................................... 25
7.1 Features........................................................................................................................................................25
7.1.1 Overview of features.......................................................................................................................................................... 25
7.2 Controls ........................................................................................................................................................25
7.3 Getting started with the EGO LOOK controller ............................................................................................27
7.4 Symbol s ........................................................................................................................................................28
7.4.1 Symbols in the status bar.................................................................................................................................................. 28
7.4.2 Speller Symbols ................................................................................................................................................................. 28
7.4.3 Symbols for menu options................................................................................................................................................. 29
7.4.4 Contact list number types ................................................................................................................................................. 29
7.4.5 Music player symbols/buttons.......................................................................................................................................... 29
7.5 Speller ..........................................................................................................................................................30
7.6 Getting started..............................................................................................................................................30
7.6.1 About Bluetooth®technology ............................................................................................................................................ 30
7.6.2 Activating the controller .................................................................................................................................................... 31
7.6.3 On / Off function................................................................................................................................................................. 31
7.6.4 Entering the Bluetooth®PIN ............................................................................................................................................. 31
7.6.5 Hands-free mode ............................................................................................................................................................... 31
7.6.6 Automatic coupling ............................................................................................................................................................ 31
7.6.7 Calling ................................................................................................................................................................................ 32
7.7 The menus ....................................................................................................................................................34
7.7.1 User management ............................................................................................................................................................. 36

4 |5
7.7.2 Settings............................................................................................................................................................................... 37
7.7.3 iPodTM Player ...................................................................................................................................................................... 40
7.7.4 Music player ....................................................................................................................................................................... 40
7.7.5 Contacts list ....................................................................................................................................................................... 41
7.7.6 Call history ......................................................................................................................................................................... 42
7.7.7 Messages ........................................................................................................................................................................... 43
7.8 Voice control .................................................................................................................................................43
8 Software update............................................................................................................ 46
9 Service .......................................................................................................................... 47
10 Accessories and spares parts ....................................................................................... 50
10.1 Connection Concept EGO mute cable...........................................................................................................51
11 Technical specifications................................................................................................. 53
12 Certification................................................................................................................... 53
13 Conformity statement ................................................................................................... 54
14 Hotline........................................................................................................................... 56

EGO LOOK
List of illustrations
Fig. 01: Scope of Delivery.............................................................................................................9
Fig. 02: Signal direction of the Bluetooth®antenna......................................................................11
Fig. 03: Installationlocation of the electronics box......................................................................12
Fig. 04: Installation location of the microphone ..........................................................................12
Fig. 05: Installation location of the radio controller....................................................................13
Fig. 06: Installation location of the display ..................................................................................13
Fig. 07: Assembly dimensions of the electronics box..................................................................14
Fig. 08: Connection for the mini ISO connection cable................................................................16
Fig. 09: ISO-Profi box ...................................................................................................................17
Fig. 09a: EGO mute cable ...............................................................................................................17
Fig. 10: Installationprocedure......................................................................................................18
Fig. 11: Setting the PIN according to device type ........................................................................19
Fig. 11a: Connector assignments ..................................................................................................19
Fig. 11b: Connection system ..........................................................................................................19
Fig. 12: Setting the PIN according to device type (EGO mute cable) ...........................................20
Fig. 12a: Connector assignments EGO mute cable .......................................................................20
Fig. 12b: Connection system EGO mute cable ...............................................................................20
Fig. 13a/b: View after changing cables .............................................................................................21
Fig. 14: Connecting external loudspeakers .................................................................................22
Fig. 15: Connecting electronics box.............................................................................................23
Fig. 15a: Connecting EGO iDapter ..................................................................................................24
Fig. 16: Status bar ........................................................................................................................28
Fig. 17: Connection Concept EGO mute cable..............................................................................51

Introduction / foreword3
Congratulations on your new EGO!
The EGO LOOK combines functionality with a brilliant visual effect. This is evident in its beautiful design, in the numerous
functions, and primarily in its color display. The high-resolution display is generously sized and provides you with all the
important information such as contact list entries, SMS (text) messages, and more. Intuitive menu prompting and wireless
remote control ensure that you always have an overview.
The installation of your EGO LOOK in your car requires specialized knowledge and skills. We therefore recommend that the
installation be performed by a qualified professional.
Before installation in your car, please make sure that your mobile phone is fully compatible with EGO LOOK. If you are uncertain,
please consult your dealer or a qualified workshop. Our service team will also be happy to help you with any information you may
require. Further information on compatibility between EGO LOOK and various mobile phones can be found on our website.
6 |7

EGO LOOK
Safety notes4
1. Incorrect installation – Incorrect installation may lead to damage to the units and/or your car! Specialized knowledge and
skills are required for installing the system. We strongly recommend that the system be installed by a qualified rofessional.
2. Risk of injury – Unsuitable installation locations may become a source of injury in an accident situation, or may inhibit the
correct functioning of essential safety equipment. Please carefully read the notes in the „Installation“ chapter carefully!
3. Risk of injury/material damage – the removal of vehicle lining with sharp or pointed objects may lead to injuries or material
damage.
4. Road safety risk – Diverted attention can lead to dangerous situations in traffic. Even when using hands-free phone
systems, your complete attention must be paid to the current traffic conditions. It is always advisable to avoid phone calls
while driving in difficult traffic situations!
5. Damage to airbags – An incorrect installation location may cause damage to, or inhibit the correct function of, your airbags.
Do not install the components within the deployment area of the airbags!
6. Insulation damage – Damaged insulation can lead to equipment and wiring damage. The cables and leads may not be under
tension when installed. Install the cables and leads in such a way as to avoid pinching or abrasion.
7. Polarity and shorting damage – Cables connected with reversed polarity, or in such a way as to produce a short circuit, can
lead to serious damage to your equipment. Before commencing installation, make sure that the car battery is disconnected.
8. Damage to essential vehicle components – Essential vehicle components or wiring can be damaged when drilling
mounting holes or screwing in self-threading screws. Please make sure there is always sufficient space behind the screw
holes and drilled holes!
9. Interference with on-board electronics – Despite the extreme protection against interference, incorrect installation can
lead to interference with the vehicle electronic systems. Please read the vehicle manufacturer’s notes to this effect!
10. Appropriate use – The EGO LOOK is intended exclusively for use in vehicles with Bluetooth®mobile phones and A2DP
devices.
11. Damage caused by inappropriate replacement parts – Inappropriate spare or replacement parts may lead to malfunctions.
Please use only the approved parts listed in the section „Spares parts and accessories“!
12. Road safety risk – For your own safety, never initiate the coupling procedure while your vehicle is in motion!

Scope of delivery / package content5
Supplied version 1
[1] Electronics box
[2] Display and base
[3] Radio controller including battery (CR2477 type)
[4] Microphone
[5] Adhesive pad for the base
[6] Quick Guide / Safety manual
[7] ISO adapter cable
Supplied version 2
[1] Electronics box
[2] Display and base
[3] Radio controller including battery (CR2477 type)
[4] Microphone
[5] Adhesive pad for the base
[6] Quick Guide / Safety manual
[8] EGO mute cable
[9] ISO-Profi box
Supplied version 3
[1] Electronics box
[2] Display and base
[3] Radio controller including battery (CR2477 type)
[4] Microphone
[5] Adhesive pad for the base
[6] Quick Guide / Safety manual
* without cable
PLEASE MAKE SURE THE CONTENT OF THE PACKAGE is complete. If any parts are missing, please don‘t hesitate to contact our
service hotline team: (+1) 858.566.2170, Mon – Fri, 8 AM to 5 PM (PST)
[1]
[5]
[3]
[2]
[4]
[7]
[9]
D
green
I S O - P R O F I
ADIO
brown 31
30 +12V
red
violet
yellow Muting in
PEAKER
phone
white
Muting out
R S
ABENDORFER R ADIO UTE M
Safety Instructions
1. Improper installation – Improper installationmay cause damages tothe unit or tothe vehicle! e installation of thehands-free car kit requiresspezial knowledge and special
abilities. We thereforestronglyrecommend to have the installation oneby a professional.
2. Per son al inju ry – Inappropriate places forthe installation maycause personal injuries inaccidentsor may disable thesafety equipment. Note the directionsin the chapter
“Installation”!
3. Per sona l injury / Materia l damage – Whenyou remove coveringsor armatureparts, sharp tools maycause personal injuriesor materialdamage. Removethe parts carefully.
Don’t submit theconnectingcables topressure.
4. Negat ive eects on roadsa fety – Talking whilstdriving reduces your concentration. is maycause dangerous situations onthe road. Alsoin hands-free mode, you shoulddraw
your attention to thetrac. In complextrac situations you should refrain from using the mobilephone!
5. Damageof t heairbag – A wrong place selectedfor the installationof the components maycause damageto the air bag orimpair the functioningof the air bag.Install the
components out of range of ac tion of the air bag!
6. Insulation da mage – Damaged insulations maycause damages of the unit. e cables installed shouldnot be exposed to tensile stress. Install the cables such as theyare not
pinched or chafed.
7. Damagecause d by polarity reversalor s hort circuiting – Incorrectly connected cables ora short circuit maycause serious damage to theequipment. Itis essentialto disconnect
the car battery before you begin installation.
8. Damageof imp ortant vehic le components – Drilling mounting holes ordriving in self-tapping screws may causedamage to importantvehiclecomponents orto cables.Make sure
there isenough space le alsobehind thescrews unddrilling holes!
9. E  e c t s on the v e h i c l e ’ s electricalsystem – Althou gh the hands-free ca r kit produces low amounts of radiat ion, improper install ation of the hands-free car k it may inuence the
electronic equipment ofthe car. Note the directionsof the vehicle manufacturer!
10. Proper use – is system is intended for useexclusivelywith mobilephonesin motor vehicles.
11. Damagesc aused by false replacementparts – False replacement partsmay causedisturbances. Onlyuse the replacement partslisted in the chapter“Replacementparts and
Accessories”!
12. Ne gative impac t on drivings afety – For your own safet y, please do not per form a pairing procedure w hile driving!
Thank you for choosing a product from Funkwerk Dabendorf.
This Quick Guide leads you through the initial set-up of EGO LOOK.
We recommend using the operating instructions for your cellular
phone (or similar) to familiarize yourself with the Bluetooth
®
functions. Please make sure before installation that the cell
phone is compatible with the unit.
More information and detailed operating instructions can be
found on our website at www.fwd-online.de.
If you have any questions, call our hotline at [phone].
- Electronics box
- Display
- Control unit
- Microphone
- ISO cable for connecting to the vehicle
- Adapter cable
- Adhesive pad
- Quick Guide
- Safety information
Funkwerk Dabendorf GmbH
Märkische Straße
15806 Dabendorf
Germany
Telephone [phone]
Fax [phone]
E-mail [e-mail]
Internet www.fwd-online.de
EG O LOOK
Connection Concept
QUICK
GUIDE
A Funkwerk AG company.
Welcome
Contents
130 8011 1.02
Connection
for EGO LOOK
display
Line out
connection,
e.g. car radi o
Microphone
connection
Connection,
e.g.
MP3 player
ISO connection
for the vehicle
cable loom
ISO connection
to car radio
Connection
for the
Stereo Mute Box
Baseplat e connector
for mounted ch arger
(optional)
Connection
for ISO cabl e
EGO LOOK
Bluetoot h QD ID B012939
[6]
[8]
Fig. 01:
Scope of Delivery

8 |9

EGO LOOK
Installation instructions6
6.1 Required configuration
Before installation of your EGO LOOK, please note which features and connection options are provided by your car audio system.
It is advantageous when your audio has the following: a muting function, phone input and line-in. You can find out which of these
input options your audio system has in the documentation provided.
6.1.1 Vehicle
The EGO LOOK may only be installed in vehicles with 12 V, with the negative terminal connected to the chassis. If no car audio
is installed, an add-on speaker will be required. For the installation of the optional charging cradle, you will require a model-
specific mounting that may be purchased from a specialist dealer.
6.1.2 Mobile phone
Operation of the EGO LOOK requires a Bluetooth®-compatible mobile phone. You can find a list of supported Bluetooth®
telephones online at www.egohandsfree.com .
6.1.3 Muting (radio mute switch)
The muting function (Radio Muting) ensures that the audio sound is turned off during telephone calls. The system supports the
muting function. Your car`s audio documentation will show whether your car audio has a mute option. If your car audio is not
equipped with a muting option, you can install the optionally available Stereo Mute Box to facilitate speaker muting.
6.1.4 Converting the EGO LOOK into a previously installed Funkwerk hands-free car kit
An adapter cable is available for customers who already own a Funkwerk hands-free car kit (including the Audio 2000, 3000,
Audio blue, Audio com, and Audio compact) and who would like to easily convert the EGO LOOK. The adapter cable connects the
ISO cable, already installed in the vehicle, of your previous Funkwerk handsfree system with the EGO LOOK and is available as
an accessory.
NOTE! This simple converting option is only possible when installing the EGO LOOK without a stereo mute box. To install the
EGO LOOK with the stereo mute box, the stereo mute box’s ISO connecting cable should be used to connect to the vehicle.
6.1.5 Add-on speakers / Car audio telephone connection
The car’s loudspeakers are transferred to the system is by means of switch contacts. These are designed for a peak power
handling of 35 W (Sinus). Loudspeaker power handling exceeding 35 W leads to premature wear on the switching contacts. For


higher outputs, use the telephone connection of the car audio or a 5 W / 4-Ohm satellite speaker. This port is only designed for
voice reproduction.
6.1.6 Car radio line-in
A car audio with a line-in input option is required for music reproduction in stereo. As an alternative to line-in, the car audio may
have a mini-ISO port (block connector C), a 0.14 in jack socket or a RCA input socket. An appropriate adapter lead is required
for the connection between the EGO LOOK line-out and the line-in version of your audio system. If your car audio system has no
line-in option, you can employ the optionally available Stereo Mute Box for stereo reproduction in combination with your car’s
front speakers.
6.2 Installation locations
RISK OF INJURY! Unsuitable installation locations may become a source of injury in an accident (or emergency braking) situation,
or may inhibit the correct functioning of essential safety equipment!
6.2.1 Checking cable lengths
Before you’ve securely installed the components, check that the installation locations have been selected in such a way that the
cable length is sufficient to connect the individual components.
6.2.2 Selection of site for installing the electronics box
The Bluetooth®antenna for connection to the mobile phone and the
antenna for radio communication with the radio control unit are contained
in the electronics box. The antenna transmits directionally towards the
front. For this reason, during installation, ensure that the antenna faces
into the passenger cell (see Fig. 02). Vertical mounting is ideal. Metallic
screening between the front panel and the passenger cell, such as metal
or metallised plastic panels, are unsuitable and may interfere with the
Bluetooth®connection. Locations behind the dashboard or in a metal-
lined glove compartment are also unsuitable.
A covering in plastic, fabric or wood presents no problems whatsoever.

Fig. 02:
Signal direction of
the Bluetooth
®
antenna
10 |11

EGO LOOK
Suitable locations for the electronics box:
Passenger side, next to the middle console under the paneling, model-
specific installation console (dealer).
Our suggested installation locations are shown in the illustration on the
right.
Further unsuitable locations are:
Leg and knee height, potential head impact zone, airbag inflation space,
engine compartment
6.2.3 Selection of site for installing the microphone
Suitable for the microphone:
Where voice can reach the microphone unhindered (distance
between the speaker and the microphone should be approx. 13.78
in), on the A-column (between windshield and driver’s side window),
next to the driver‘s sun visor, on the dashboard
Unsuitable for the microphone:
Close to the speakers (less than 31 in), under the dashboard, in the
air stream from open windows or air vents.
Fig. 03:
Installation
location of the
electronics box
Fig. 04:
Installation location of
the microphone
The illustration shows
one of the potential
microphone mounting
locations. Alternatively,
the microphone may be
attached to the sun visor
with the clip provided.

6.2.4 Selection of site for installing the radio controller
The following locations are suitable for the radio controller:
In the area above the DIN installation slot, in the vicinity of the steering
wheel (at a location within the driver’s reach).
The following locations are unsuitable for the radio controller:
Airbag deployment area, possible head impact area, beyond the reach of
the driver.
6.2.5 Selection of site for installing the display
The following locations are suitable for the display:
In the space above the DIN installation shaft, close to the steering wheel
(in an easily accessible and visible position), Note the position of sunlight
to avoid reflection on the display.
The following locations are unsuitable for the display:
Airbag inflation space, potential head impact zones, out of reach of
driver’s reach.
Fig. 05:
Installation location of
the radio controller
Fig. 06:
Installation location of
the display
12 |13

EGO LOOK
6.3 Installation
DAMAGE TO ESSENTIAL VEHICLE COMPONENTS! Essential vehicle components or wiring can be damaged when drilling mounting
holes or screwing in self-threading screws. Please make sure there is always sufficient space behind the screw holes and drilled
holes!
6.3.1 Mounting the electronics box
Installation consoles for a number of car models are
available from your dealer. These are designed to contain
all the system components, including the electronics box.
When it is not possible to use an installation console,
please proceed as follows:
Define the mounting points
Making sure that there is at least 2.8 in space for the plug
and socket connectors. Mark the positions for the fixing
screws.
Mounting the electronics box
For mounting the electronics box, use four self-threading screws and appropriate washers. We recommend size “ST 2,9x25 DIN
7981”self-threading screws. These are ideal for the fixing of the electronics box. Pre-drill the holes with a 0.08 in drill.
6.3.2 Mounting the microphone
Define the mounting location
The microphone holder has a self-adhesive strip on the back. The mounting location should have the same form and area as the
self-adhesive strip on the microphone holder. The location selected must allow the microphone cable to reach the electronics
box! Position the microphone with the head facing towards the direction of speech.
Cleaning and degreasing the mounting location
The mounting location must be clean and free from grease and dirt/dust. Prior to installation, clean the area with a cleansing
product containing ethyl alcohol. Only use products that do not damage plastics or varnished wood finishes and are themselves
free of oils or grease. Unsuitable cleansers are, for example, lighter fluid, acetone, turpentine, trichloroethylene and similar
products.
Attaching the microphone holder
Peel off the protective backing from the self-adhesive strip. Hold the microphone holder at a distance of several millimetres
(about a quarter of an inch) above the desired mounting location. Re-check the positioning. Re-positioning after mounting is no
longer possible. Place the microphone holder on the mounting location and fix by applying short and light pressure.

Fig. 07:
Assembly
dimensions of
the electronics
box

Attaching the microphone
Attach the microphone by sliding it into the holder and position the microphone head towards the direction of speech.
6.3.3 Inserting the battery in the radio controller
CAUTION! Danger of explosion in the case of incorrectly changing the battery!
Disposal of used batteries according to manual!
Rotate the lower portion of the controller clockwise and the upper portion counterclockwise to open the controller. Lift the
upper portion. Insert the supplied battery with the positive terminal downward into the lower portion until it latches. Now place
the upper portion on the bottom so that the contacts from the bottom of the controller touch the contact surface in the upper
portion. Position the latching tabs in the notches and rotate opposite the opening direction.
6.3.4 Mounting the radio controller
Define the mounting location
The control console is mounted on a smooth service by means of the self-adhesive pad provided. Make sure that the user can
easily reach the controller.
Cleaning and degreasing the mounting location
The mounting location must be clean and free from grease and dirt/dust. Prior to installation, clean the area with a cleansing
product containing ethyl alcohol. Only use cleansing products that do not damage plastics or varnished wood finishes and are
themselves free of oils or grease. Unsuitable cleansers are, for example, lighter fluid, acetone, turpentine, trichloroethylene
and similar products.
Gluing the radio controller in position
Remove the protective foil from the adhesive pad on the underside of the controller. Hold the radio controller a few millimeters
over the desired installation position. Check the position again – when doing so, keep the position of the red and green buttons
in mind. It is not possible to correct the controller after it has been glued in position. Place the radio controller on the adhesive
location and briefly apply moderate pressure.
6.3.5 Mounting the display
Determining the mounting location
The display is mounted to a smooth surface using the supplied adhesive pad. The optimal position for this is facing directly at
the driver. Keep the effect of lights and sunlight in mind in order to minimize possible reflections.
Cleaning and degreasing the mounting location
The mounting location must be clean and free from grease and dirt/dust. Prior to installation, clean the area with a cleansing
product containing ethyl alcohol. Only use cleansing products that do not damage plastics or varnished wood finishes and are
14 |15

EGO LOOK
themselves free of oils or grease. Unsuitable cleansers are, for example, lighter fluid, acetone, turpentine, trichloroethylene
and similar products.
Gluing the display in position
Pull the protective foil from the adhesive strips. Hold the display a few millimeters over the desired installation position. Check
the position again. It is not possible to correct the display after it has been glued in place. Place the display on the adhesive
location and briefly apply moderate pressure.
Changing the base position
As supplied, the display base is intended for vertical mounting in the vehicle. To change to the horizontal mounting position,
unlatch the base, rotate 180° and re-latch the base on the underside of the display.
6.4 Connection scheme
6.4.1 Preface
Installation for call reception for a car audio system with a mute input but without a phone input
With this connection option, voice playback is is emitted from the front right car speaker. During calls, the mute input blocks the
car audio signal.
NOTE: Please observe the information in section “6.5.1 Checking the mute inputs” on connecting the mute lead of the ISO
connecting cable.
Installation for voice playback with a car audio system with phone and mute input options
With this connection option, voice playback comes through the car audio system speakers.
During calls, the car radio output is switched to the phone input by the mute input In order
to access the phone input of your car audio system, the speaker output of your EGO LOOK
must be connected to the phone input of your car audio system. The purple and green leads
of the ISO cable must be connected to the car audio phone input for this option. The purple
and green leads must be disconnected from the ISO connector. The green lead (pin 14 of the
14-pin plug) should be connected to „Phone Out“, and the purple lead (pin 7 of the 14-pin
plug) to „Phone In +“ of the Mini-ISO socket.
Informationen zum Telefoneingang Ihres Autoradios entnehmen Sie bitte der Einbau- und
Bedienungsanleitung Ihres Autoradios.
NOTE: If your car audio system has different phone connection options from those mentioned here, please consult a qualified
professional for installation of the system. Furthermore, please read the section with information on connecting the mute lead
of the ISO connection cable, “6.5.1 Checking the mute input”.

Fig. 08:
Connection for
the mini ISO
connection cable


6.4.2 EGO mute cable
NOTE: An MP3can be played using Bluetooth via the connection of the line out at the
automobile radio!
For calls with the cell phone in connection with a hands-free system in the automobile,
the loudspeakers of the automobile radio are switched off by the radio mute change-
over. The two front loudspeakers are switched over to the NF output of the hands-free
system and thus used to render the telephone call.
Properties:
- complies with the legal regulations of the consumer protection [CE]
(European Directives)
- easily operated hands-free system in each automobile with radio
device and at least two loudspeakers
- automatic activation by hands-fee system for every telephone call
- the driver is not distracted by operating the radio
- no installation of additional loudspeakers required for the hands-
free system
Fig. 09: ISO-
Profi box

Fig. 09a:
EGO mute cable
16 |17

EGO LOOK
6.5 Installing the ISO connection cable
The battery must be disconnected before starting cable installation. Disconnect the grounding cable from the negative pole of
the battery. The cable installation procedure is shown in the illustrations.
When the installation is completed, reconnect the grounding cable to the negative pole of the battery.
6.5.1 Checking the mute inputs / ISO-Profi
The mute inputs 1-3 can be seen in Fig. 5 of Illustration 10. The yellow mute cable of the hands-free equipment is connected to
one of these inputs. The table below shows which mute input is to be used:
2
Connect 14-pin ISO
connecting cable to
EGO LOOK
Disconnect car wiring
harness from car radio
Connect EGO LOOK ISO
connector to car radio
Connect EGO LOOK ISO connectors to car
wiring harness ISO connectors
Connect yellow mute lead to
one of the three mute inputs
(see table)
Electronics box
Car audio Car audio
Fig. 10:
Installation
procedure

18 |19
Fig. 11:
Setting the
PIN according
to device type
Fig. 11a:
Connector assignments
Fig. 11b:
Connection system
Socket contact housing Wiring of power supply connectors
Radio model Pin Wire colour Function
Audi,
Volkswagen,
Grundig
1
2Mute
3
4blue Ignition (15)
7red Permanent positive (30)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Ford,
Mercedes,
Porsche,
Becker
1
2
3Mute
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Blaupunkt
1
2Mute
3
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Philips
1Mute
2
3
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket wiring from
the rear (see table)
Plug wiring from
the rear
Car audio
Electronics box
Vehicle wiring harness

EGO LOOK
Fig. 12:
Setting the
PIN according to
device type (EGO
mute cable)
Fig. 12a:
Connector assignments
EGO mute cable
Fig. 12b:
Connection system
EGO mute cable
Socket contact housing Wiring of power supply connectors
Radio model Pin Wire colour Function
Audi,
Volkswagen,
Grundig
1
2Mute
3
4blue Ignition (15)
7red Permanent positive (30)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Ford,
Mercedes,
Porsche,
Becker
1
2
3Mute
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Blaupunkt
1
2Mute
3
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket contact housing
Radio model Pin Wire colour Function
Philips
1Mute
2
3
4red Permanent positive (30)
7blue Ignition (15)
8brown Ground (31)
Socket wiring from
the rear (see table)
Plug wiring from
the rear
Car audio
Electronics box
Vehicle wiring harness
ISO-Profi