Furniture of America CM-DK6846 User manual

Assembly
Instructions
EASY DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-DK6846
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Rev:16-09-05
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page
2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches
Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#A x 16pcs
#B x 16pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Cabinet body
#3 x 2pcs #C x 16pcs
Page 3 of 8
Leg
Hutch Top
Bolt 1/4 x 2"
Flat Washer Ø1/4"
Lock Washer Ø1/4"
#4 x 4pcs
#5 x 1pc
Hutch panel
Hutch Back
#E x 4pcs
#F x 4pcs
Allen Key 4mm
#D x 1pc
Barrel Nuts Ø1/4"
Bolt 1/4" x 1-3/8"
#6 x 2pcs
#7 x 2pcs
Drawer
Mirror Support
#8 x 1pc
Mirror

Page
4 of 8
#A x 8pcs
#B x 8pcs
#C x 8pcs
#A x 2pcs
#E x 2pcs
#1 #2
#A
#C
#B
#D
#3
#5 #4
#4
#4
#4
#E
#E
#D
#D
#A
#A
Pull out drawer for
access to rear holes.
1. Prepare 8 bolt assemblies by first inserting a
lock washer (#C) onto the bolt (#A) then a
flat washer (#B) onto that same bolt (#A).
2. Align the legs (#2) to the holes
along the corners of the body (#1),
then insert the bolt assemblies
from within and secure using the
Allen wrench (#D).
1. Insert the pins along the
hutch panels (#4) into the
holes along the hutch back
(#5) and hutch top (#3) as
shown above.
2. Insert the barrel nuts (#E)
into the large holes along the
hutch back (#5), make sure
the holes face the open-ings.
Then insert the bolts (#A) into
the hutch top (#3) and secure.

Page 5 of 8
#A x 2pcs
#E x 2pcs
#5
#1
#A
#D
#5
#1
#E
Insert each end into
the holes along the
cabinet body (#1).
1. Insert the barrel nut (#E)
into the large holes
along the hutch back (#5)
make sure to align the
hole.
2. Insert the bolts (#A)
into the holes from
beneath and into the
nuts. Secure using the
Allen wrench (#D).

#F
#C
#B
#D
Page 6 of 8
#B x 4pcs
#C x 4pcs
#F x 4pcs
#A
#C
#B
#D
#1
#A x 4pcs
#B x 4pcs
#C x 4pcs
#8
#7
1. Prepare 2 bolt assemblies by first
inserting a lock washer (#C) onto the bolt
(#A) then a flat washer (#B) onto that same
bolt (#A).
2. Insert into rear inner
holes and secure.
1. Prepare 4 bolt assemblies by
first inserting a lock washer (#C)
onto the bolt (#F) then a flat
washer (#B) onto that same bolt
(#F).
2. Place the mirror (#8) onto the body (#1).
Align the mirror supports (#7) to the holes
along the back, then insert the bolt
assemblies and secure.

Page 7 of 8
#6
ASSEMBLY IS COMPLETED
Insert the drawers (#6)

#A
#C
#D
#B
Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#A x 8pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Seat
#B x 8pcs
Page 8 of 8
Leg
Bolt Ø1/4" x 2"
#C x 8pcs
/RFN Washer Ø1/4"
#D x 1pc
Allen Key 4mm
#A x 8pcs
#B x 8pcs
#C x 8pcs
Flat Washer Ø1/4"
#2
#1
1. Prepare 8 bolt assemblies by first inserting
a lock washer (#C) onto the bolt (#A) then a
flat washer (#B) onto that same bolt (#A).
2. Align the legs (#2), then insert the bolt
assemblies from within and secure.