Furniture of America CM-AC592 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
For more information contact our team: [email protected]
CM-AC592
Phillips Screwdriver
(Not Included)
Rev:19-06-02

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 7
Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#5 x 1pc
#6 x 1pc
#7 x 1pc
#8 x 1pc
Upper Right Frame
Upper Left Frame
Shelf 1
Shelf 2
Shelf 3
Shelf 4
#3 x 1pc
#4 x 1pc
Lower Right Frame
Lower Left Frame
#A x 4pcs
Allen Key 4mm
#D x 1pc
#B x 16pcs
#C x 16pcs
Bolt Ø1/4" x 1-3/8"
Bolt Ø1/4" x 2-3/8"
Barrel Nuts Ø1/4"
Wood Dowel Ø10x40mm
#E x 4pcs
#F x 4pcs
Screw #4 x 35mm
Screw #3 x 15mm
#G x 2pcs
Flat Washer Ø4 x 10mm
#H x 4pcs

#9 x 1pc
Smoking box
#1
#2
#3
#4
#5
#6
#7
#8
#9
Page 4 of 7
Parts List
Hardware List
Screw #3.5 x 20mm
#I x 2pcs
Tox
#J x 2pcs
#K x 2pcs
Fabric

#A
#D
#A x 4pcs
#B x 4pcs
#C x 4pcs
#8
#9
#B
#B
#C
#C
#1
#2
#5
#6
#7
#3
#4
#B
#B
#C
#C
#B x 12pcs
#C x 12pcs
#D
#D
Page 5 of 7
1) Align lower right and left frames (#3,4) to the shelf (#8) and smoking box (#9). Secure
frames (#3,4) to shelf (#8) by using bolts (#B) with barrel nuts (#C).
2) Secure frames (#3,4) to
smoking box (#9) by using
bolts (#A).
Align upper right and left frames (#1,2) to shelves (#5,6,7),
then secure by using bolts (#B) with barrel nuts (#C).

Page 6 of 7
#E x 4pcs
#F x 4pcs
#F
#E
#E
#2
#1
#3
#4
#9
Insert dowels (#E) to holes of the lower frames (#3,4),
then align the upper frames (#1,2) to the lower frames
(#3,4). Secure by using screws (#F).
Detach handle from the inside of drawer, then
secure handle to the outside of drawer.

Page 7 of 7
ASSEMBLY IS COMPLETED
#J
#H
#I
#H#G
#K
#G x 2pcs
#H x 4pcs
#I x 2pcs
#J x 2pcs
#K x 2pcs
Wall Strap
1) Align strap (#K) to top back corners of the
product, then secure by using screws (#G) with
washers (#H).
2) Align and measure product with strap to the wall,
then drill a hole in the wall. Insert plastic inserts (#J)
to the hole of the wall, then align strap (#K) to plastic
inserts (#J). Secure by using screws (#I) with
washers (#H).