Furniture of America CM-BK922T User manual

Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-02-26
CM-BK922T
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
Page 1 of 11

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 11

Parts List
#1 x 1pc
#2 x 1pc
#4 x 1pc
#9 x 2pcs
Lower bad rail
#10 x 2pcs
#11x 2sets
#12 x 1pc
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
4 Drawers chest
#3 x 1pc
#5 x 1pc
#7 x 1pc
#6 x 2pcs
#8 x 1pc
#13 x 4pcs
Hardware List
#A x 8pcs
Bolt Ø1/4"x3-1/8"
#B x 8pcs
Left side panel
Right side panel
Small rung
Large rung
Support bar
Right headbroad
Left headbroad
Upper bad rail
Slats
Back panel
Guardrail
Bolt Ø1/4"x2-3/8"
Page 3 of 11

Hardware List
#I x 4pcs
Bolt Ø5/32"x1"
#J x 4pcs
#K x 12pcs
#L x 16pcs
#C x 12pcs
Bolt Ø1/4"x1-3/16"
#D x 2pcs
#E x 1pc
#F x 8pcs
#M x 16pcs
#N x 16pcs
#G x 8pcs
#H x 8pcs
#1
#13
#2
#3
#4
#6
#7
#8
#5
#9
#10
#12
#11
#11
Allen Wrench M4
Straight Allen Key
Screw Ø1/4"x2-9/16"
Knob
Barrel Nut Ø1/4"
Wood Dowel Ø3/8"x1-9/16"
Rail Bracket Ø1/4"
Screw Ø1/4"x1-3/4"
Screw Ø1/4"x1-3/8" Screw Ø5/32"x1-3/16"
Page 4 of 11

#I x 4pcs
#J x 4pcs #1
#2
#G x 2pcs
#D
#G
#I #J
#1
Page 5 of 11
Secure knobs (#J) to the holes of the drawers by using bolts (#I).
Align drawers chest (#1) to the holes of the left side panel (#2),
then secure by using screws (#G).

#F x 2pcs
#H x 4pcs
#L x 16pcs
#4
#5
#D
#F
#L #L
#L
#L
#9,#10
#13
#H
#12
x 2
x 4
#2
#D
Page 6 of 11
Align back panel (#12) to the upper holes of
the left side panel (#2), then secure by using
screws (#F).
Align rungs (#4,5) to the lower holes of the
left side panel (#2), then secure by using
screws (#H).
Attach dowels (#L) to the holes of the side rails (#9,10,13).

#A
#7
#M
#M
#D
#B
#8
#9
#9
#10
#10
#A x 8pcs
#B x 8pcs
#M x 16pcs
#D
#G
#F
#13
#F x 4pcs
#G x 4pcs
#8
#7
Page 7 of 11
Align side rails (#9,10) to the holes of the headboards (#7,8). Insert bracket (#M) to the
holes of the side rails (#9,10). Secure side rails (#9,10) to headboards (#7,8) by tightening
bolts (#A,B) to the brackets (#M). Do not fully tighten bolts (#A,B).
Use bolts (#A) on this side.
Use bolts (#B) on this side.
Align and attach rails (#13) to the holes of the headboards (#7,8).
{If you are having a tough time fitting rails (#13), then loosen bolts
(#A,B) from steps #5.} Secure rails (#13) by using bolts (#G,F).
Use bolts (#F) on this side.
Use bolts (#G) on this side.
FULLY TIGHTEN ALL BOLTS ON
STEPS #5 and #6.

#6
#6
#K
#C
#D
#C x 6pcs
#K x 6pcs
#C x 6pcs
#K x 6pcs
#K
#C
#D
#3
#8
#13
Page 8 of 11
Align support bars (#6) to the holes of the rails (#13), then secure by
tightening bolts (#C) to nuts (#K).
Align right side panel (#3) to the holes of the left headboard (#8),
then secure by tightening bolts (#C) to nuts (#K).

#D
#H
#G x 2pcs
#H x 4pcs
#F x 2pcs
#D
#F
#12
#D
#G
#3
#3
Page 9 of 11
Align stair case to the holes of the right side panel (#3), then secure by using screws (#G,H).
Use screws (#H) here.
Use screws (#G) here.
Secure upper holes of the right side panel (#3) to the stair case by using screws (#F).

#N
#11
#11
#N x 16pcs
ASSEMBLY IS COMPLETED
#N
Page 10 of 11
Align slats (#11) to the side rails, then secure by using screws (#N).