Furniture of America YNJ-318-5 User manual

Page 1 of 11
The Assembly Rating is a 5-point system that
show the degree of effort needed in assem-
bling a specific product (with 1 being easy and
5 being difficult). For most products, two per-
sons are recommended.
Allen Wrench
Phillips Screwdriver
(Included)
(Not Included)
YNJ-318-5
ASSEMBLY INSTRUCTIONS
ASSEMBLY RATING TOOLS REQUIRED FOR ASSEMBLY
14-10-24
EASY DIFFICULT 2 PERSONS RECOMMENDED

Page 1 of 15
Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 11

Page 3 of 11

Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION
Page 4 of 11

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly
Page 5 of 11

DRESSER / CHEST
ASSEMBLY INSTRUCTIONS
Please keep for future reference
MODEL # YNJ-318-5
PARTS LIST
HARDWARE LIST
Before you begin, please
read “Assembly and
Care Advice”, “Pre-
Assembly Introduction”
and “Cam Lock Fastener
Assembly Instructions”.
Page 6 of 11
DIMENSIONS
29.69”(W) X 17.13”(D) X 43.5”(H)
29.69''
43.5''
17.13''
J
E
I
H
K
C
N
A
E
A1PC
1PC
1PC
2PCS
2PCS
5PCS
F1PC
1PC
C
H
G
E
D
B
I1PC
1PC
A
J
Q
P
O
N
M
L
K
5PCS
5PCS
5PCS
5PCS
1PC
5PCS
I1PC
1PC
1PC
F
122PCS
610SETS
54PCS
6SETS
10PCS 436PCS
910PCS 10 22PCS
81PC
10SETS
7
25
x20PCS
3

STEP1
Hardware #2 = 8pcs
Hardware #5 = 10 runners + 20 screws
ASSEMBLY INSTRUCTIONS
Page 7 of 11
Assembling Drawer’s Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is composed of
an inner rail and outer slide. Please read completely first before assembling.
Mounting the Inner Rail (Fixed) of the Runner: Before mounting, please determine
which side of the panel is the front and rear. The single screw hole on the outer slide
MUST be positioned on the FRONT of the panel. Place the inner rail of the runner in
its correct position and flat on its back. Slide the outer slide out to the way to align the
center or second holes on both ends of the inner rail with the pre-drilled holes on the
panel. For most applications, the center or second holes are used but if not, just make
sure the appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner: Each outer rail is secured with
a single screw onto the FRONT SIDE of the drawer. Extend the two outer slidesof the
runners and place the drawer in between those two outer slides. Align the pre-drilled
holes on each side of the drawer with the screw holes of the outer slides. Use two
screws to secure from the inside of the drawer into the screw holes of the outer slides.
Screw Hole
Screw Hole
2nd Hole
Front
Front
5
C
B
2
2
8
5

STEP2
Hardware #1 = 4pcs
Hardware #4 = 16pcs
STEP3
Hardware #2 = 4pcs
STEP4
Hardware #2 = 8pcs
Hardware #3 = 2pcs
Hardware #10 = 4pcs
ASSEMBLY INSTRUCTIONS
Page 8 of 11
Screw Hole
Front
Front
4
1
J
H
E
D
D
E
K
I
B
C
F
H
JD
E
J
F
3
2
2
1
10
10
2
C
B
D

ASSEMBLY INSTRUCTIONS
Page 9 of
STEP5
Hardware #2 = 4pcs
Hardware #3 = 8pcs
STEP6
11
3
2
I
E
K
D
B
C
J
B
P
C
F

ASSEMBLY INSTRUCTIONS
Page 10 of
STEP7
Hardware #1 = 8pcs
Hardware #10 = 8pcs
STEP8
Hardware #1 = 10pcs
Hardware #2 = 30pcs
Hardware #4 = 20pcs
Hardware #6 = 10sets
Hardware #10 = 10pcs X5
X5
11
P
8
B
A
C
F
10
1
D
D
A
L
M
N
O
Q
G
6
1
1
10
2
L
M
G
O
4