Furniture of America CM-AC6562 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Tools Required For Assembly:
Allen Wrench (Included)
For more information contact our team: [email protected]
CM-AC6562
Rev:18-01-06
Phillips Screwdriver
(Not Included)

Page 2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Arm (Left/Right)
#4 x 2pcs
Leg(Left/Right)
#A x 6pcs
Bolt Ø1/4" x 2-3/8"
#B x 2pcs
Bolt Ø1/4" x 2"
#C x 9pcs
Bolt Ø1/4" x 1-1/4"
#D x 17pcs
Lock Washer Ø1/4"
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Chair Back
#3 x 1pc
Chair Seat
#5 x 1pc
Front Stretcher
#6 x 1pc
Back Stretcher
#E x 2pcs
Flat Washer Ø1/4" x 19
#F x 15pcs
Flat Washer Ø1/4" x 12.5
Page 3 of 6
#G x 1pc
Allen Wrench M4
#H x 6pcs
Barrel Nut Ø1/4"
#I x 6pcs
Nut Ø13.5 x 8mm

Page 4 of 6
#1
#2R
#2L #3
#4R
#4L #5
#6
Exploded View
#A
#D
#F
#G
#I
#4R
#5
#6
#A x 4pcs
#D x 4pcs
#F x 4pcs
#H x 4pcs
#I x 4pcs
#H
#4L
1) Insert barrel nuts (#G) to the holes of the stretchers (#5,6), then align stretchers (#5,6) to the holes of
the legs (#4R/L).
2) Prepare 4 bolts assembly by inserting lock washer (#D), then flat washer (#F) onto bolts (#A). Secure
stretchers (#5,6) by tightening bolts (#A) onto barrel nuts (#G). Cover bolts (#A) by using caps (#I).

Page 5 of 6
#C
#D
#F
#G
#C x 3pcs
#D x 3pcs
#F x 3pcs
#C x 6pcs
#D x 6pcs
#F x 6pcs
#3
#1
#C
#D
#F
#G
#1
#4L
#4R
Align chair back (#1) to the holes of the seat (#3).
Secure by using bolts (#C) with washers (#D,F).
Align legs (#4R/L) to the holes of the seat, then secure by using
bolts (#C) with washers (#D,F).

Page 6 of 6
#I
#F
#D
#B #G
#E
#D
#A
#G
#H
ASSEMBLY IS COMPLETED
#A x 2pcs
#B x 2pcs
#D x 4pcs
#E x 2pcs
#F x 2pcs
#H x 2pcs
#I x 2pcs
#1
#2R
#3
#2L
1) Align arms (#2R/L) to the holes of the chair back (#1) and
seat (#3). Secure arms (#2R/L) to chair back (#1) by using bolts
(#B) with washers (#D,F). Cover bolts (#A) by using caps (#I).
2) Insert barrel nuts (#H) to the
holes of the arms (#2R/L). Secure
arms (#2R/L) to the seat (#3) by
using bolts (#A) with washers
(#D,E) onto barrel nuts (#H).

E-commerce Division - Enitial Lab
Thanhk you for your purchase!
We hope you will enjoy your new product for many years to come to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
www.foagroup.com
[email protected]
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://instagram.com/foagroup#
http://www.pinterest.com/foagroup/
http://www.youtube.com/user/FurnitureOfAmerica
http://