Furniture of America Potterville CM-DK6490 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-DK6490
Phillips Screwdriver
(Not Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-31
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Allen Wrench (Included)

Page 2 of 5

Parts List
#1 x 1 pc
Vanity
#2 x 4 pcs
Vanity Leg
#3 x 1 pc
Mirror
#D x 8 pcs
Screw
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.
MD
#C x 16 pcs
Flat Washer
#4 x 2 pcs
Support Rail
Page 3 of 5
#E x 1 pc
Allen Wrench
Hardware List
#5 x 1 pc
Seat
#6 x 4 pcs
Chair Leg
#A x 16 pcs
Bolt 5/16”x2”
#B x 16 pcs
Lock Washer

Page 4 of 5
I. Align the support rail (#4)
with the pre-drilled holes
on the back of the vanity
(#1)AND the mirror (#3).
II. Secure 4 screws (#D) into
the support rail (#4) using
a Phillips screwdriver to
tighten them to the vanity
(#1)AND the mirror (#3).
III. Repeat the process above
to assemble the other
mirror support rail (#4)
onto the vanity (#1)AND
the mirror (#3).
I. With the help of another person,
carefully place the vanity (#1)
facing down on a protected
surface.
II. Align the 4 vanity legs (#2) with
the pre-drilled holes on the
corners of the vanity (#1).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
IV. Insert the bolt assemblies
through the pre-drilled holes on
the corners of the vanity (#1) and
secure those bolts using the
Allen wrench (#E) to lock them
with the vanity legs (#2).
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#D x 8 pcs
Turn right (clockwise) to tighten

Page 5 of 5
Make sure the vanity and chair are rested
on a flat surface and do not feel loose or
wobbly. If they do, double check the
bolts/screws are secured and properly
tightened.
ASSEMBLY IS COMPLETED
I. Place the seat (#5) facing down on
a protected surface.
II. Align the 4 chair legs (#6) with the
pre-drilled holes on the corners of
the seat (#5).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the
flat washer (#C) onto the SAME bolt
(#A), in that order.
IV. Insert the bolt assemblies through
the pre-drilled holes on the corners
of the seat (#5) and secure those
bolts using the Allen wrench (#E) to
lock them with the chair legs (#6).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
Turn right (clockwise) to tighten