Furniture of America CM4644WH-C User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM4644RD-C
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-27
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM4644WH-C CM4644BK-C
Phillips Screwdriver (Not Included)
Flat-Head Screwdriver(Not Included)

Page 2 of 6

Parts List
#1 x 1 pc
Table Top
#2 x 3 pcs
Leg
#3 x 1 pc
Rear Panel
#D x 1 pc
Allen Wrench
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
#C x 3pcs
Bolt 5/16”x1-7/8”
#4 x 1 pc
Left Panel
Page 3 of 6
#E x 6 pcs
Wood Dowel
Hardware List
#5 x 1 pc
Right Panel
#6 x 1 pc
Bottom Panel
#A x 3 pcs
Flat Washer
#B x 3 pcs
Lock Washer
#F2 x 14 pcs
Cam Connector
#G x 14 pcs
Cam Cover
#F1 x 14 pcs
Cam Bolt

Turn the cam
connector with a
screwdriver until
it will not turn any
more with light to
moderate force.
Two parts should fit snuggly
against each other.
Secure the
threaded end
of the cam
bolt by using
a screwdriver.
Insert the cam lock
bolt into the pre-
drilled hole above
the cam connector.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Turn right (clockwise) to tighten
Note: Every cam lock bolt must have a cam lock connector in order to fasten the parts together.
Align the cam connector with its
side opening (or arrow)
pointing to the small
drilled hole.
Turn right (clockwise) to tighten
I. Carefully place the table top (#1)
facing down on a protected surface.
Insert two wood dowels (#E) into the
corner of the table top (#1).
II. Align the leg (#2) with the wood
dowels (#E) and the pre-drilled hole
in the corner of the table top (#1).
III. Prepare a bolt assembly by inserting
FIRST the lock washer (#B) onto the
bolt (#C) and then the flat washer
(#A) onto the SAME bolt (#C), in
that order.
IV. Insert the bolt assembly through the
pre-drilled hole on the leg (#2) and
secure that bolt using the Allen
wrench (#D) to lock it in with the
table top (#1).
V. Repeat the process for assembling
the remaining 3 legs (#2) onto the
table top (#1).
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
#E x 6 pcs
Page 4 of 6

Insert 4 cam bolts (#F1) and 2 cam connectors (#F2) into the right panel
(#5). Insert 5 cam connectors (#F2) into the rear panel (#3) and 4 cam
connectors (#F2) into the bottom panel (#6). See diagram below and
refer to “CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS” for
connecting those parts together. Once locked, insert a 2 cam covers
(#G) over the 2 cam connectors (#F2) located on the rear panel (#3).
Page 5 of 6
Insert one cam bolt (#F1) into the rear panel (#3) and one cam
connector (#F2) into the bottom panel (#6). See diagram below and
refer to “CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS” for
connecting those parts together.
#F1 x 1 pc
#F2 x 1 pc
#F1 x 4 pcs
#F2 x 11 pcs
#G x 2 pcs

Insert 5 cam bolts (#F1) into the table top (#1). See diagram below and refer
to “CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS” for connecting
those parts together. Once locked, insert 5 cam covers (#G) over the 5 cam
connectors (#F2).
Carefully turn the completed table upright. Make sure the table is rested on a
flat surface and it does not feel loose or wobbly. If it does, double check that
the bolts are secured and properly tighten.
Page 6 of 6
Insert 4 cam bolts (#F1) and 2 cam connectors (#F2) into the left panel (#4).
See diagram below and refer to “CAM LOCK FASTENER ASSEMBLY
INSTRUCTIONS” for connecting those parts together. Once locked, insert a
7 cam covers (#G) over the 7 cam connectors (#F2) as shown below.
ASSEMBLY IS COMPLETED
#F1 x 4 pcs
#F2 x 2 pcs
#G x 7 pcs
#F1 x 5 pcs
#G x 5 pcs