Furniture of America CM-BK1032-WH User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-05-27
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM-BK1032-WH/BK/RD/AG/SV/OR
2 PERSONS RECOMMENDED
15-08-18

Page 2 of 7

#4 x 4 pcs
Outer Support Frame
Parts List
#1 x 1 pc
End Guardrail A
#3 x 2 pcs
Side Guardrail
#7 x 2 pcs
Corner Post A
Before you begin, please read Page
2 for “Assembly and CareAdvice”
AND Page 7 for “Safety Warnings”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7
#9 x 2 pcs
Ladder Side
#6 x 2 pcs
Side Rail
#10 x 2 pcs
End Rail
#2 x 1 pc
End Guardrail B
#5 x 4 pcs
Inner Support Frame
#8 x 2 pcs
Corner Post B
#11 x 4 pcs
Ladder Rung

#D x 8 pcs
Bracket
Hardware List
#A x 36 pcs
Bolt 1/4”x5/8”
#C x 20 pcs
Bolt 1/4”x3”
#G x 4 pcs
Curved Washer
Page 4 of 7
#F x 1 pc
Allen Wrench
#B x 12 pcs
Bolt 1/4”x1-3/8”
#E x 36 pcs
Flat Washer
#H x 24 pcs
Lock Washer
Due to the size and/or weight of this product, it
is highly recommended that the assembly
should be done near the area of its intended
location. Make sure you have enough space to
move around during the assembly. ALWAYS
have at least two people to help with
transporting and assembling the product to
avoid any potential injury and/or damage.

Page 5 of 7
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
1. Insert (#1) onto the top
ends of the posts (#7,8)
2. Align the ladder side (#9) and
ladder rungs (#11). Insert a
bolt (#A) into each end and
secure using the Allen wrench.
Turn right
(clockwise)
to tighten.
3. Align the end rail (#10) to the bottom. Prepare 2 bolts by
inserting a lock washer (#H) then a flat washer (#G) onto
the bolt (#C). Insert and secure using the Allen wrench (#F).
1. Insert (#2) onto the top
ends of the posts (#7,8)
Turn right (clockwise)
to tighten.
3. Align the end rail (#10) to the bottom. Prepare 2 bolts by inserting a lock washer (#H)
then a flat washer (#G) onto the bolt (#C). Insert and secure using the Allen wrench (#F).
2. Align the ladder
side (#9) and ladder
rungs (#11). Insert
a bolt (#A) into each
end and secure using
the Allen wrench.

Page 6 of 7
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
Safety is ALWAYS the main
priority. Please take the time to
inspect the assembly and FULLY
tighten all bolts/screws from Step
1 to Step 4.
Read and follow the information on
the WARNINGS shown on the end
structure of the upper bunk and on
the carton. Do not remove warning
label from the bed. Keep these
instructions for future reference.
With the help of 2
people, hold the
end guardrails in
place while
aligning the rails.
1. Align the side rails (#6) to the bottom.
Insert a lock washer (#H) onto the bolts
(#C). Then align the brackets (#D) to the
post and insert those prepared bolts.
Secure using the Allen wrench (#F).
2. Align the guardrail (#3) to the top. Insert a lock washer (#H)
onto the bolts (#C). Then align the brackets (#D) to the outer
post and insert those prepared bolts. Insert a lock washer
(#H) onto the bolts (#B). Insert those into the inner holes.
1. Place the support
frames (#4,5) in the
positions displayed.
2. Insert a flat washer (#E) onto the bolts (#A) and insert
into the inner holes. Secure using the Allen wrench.
32 total bolt assemblies.

Page 7 of 7
Safety Warnings for Bunk Beds
1. Read and follow the information on the WARNINGS shown on the end
structure of the upper bunk and on the carton. Do not remove warning label
from the bed. Keep these instructions for future reference.
2. Always use the recommended size mattress or mattress support, or both, to
help prevent the likelihood of entrapment or falls. The proper mattress sizes
for the UPPER TWIN-SIZE bunk should be 74” to 75” long x 37½” to 38½”
wide x 6” high (no higher than 6”) and for the LOWER TWIN-SIZE bunk
should be 74” to 75” long x 37½” to 38½” wide x 6” to 8” high.
3. Surface of mattress must be at least 5 inches (127 mm) BELOW the upper
edge of guardrails.
4. Do not allow persons under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrails, ladder, handle and other
components are in their proper position, free from damage, and that all
connectors are tighten and secured.
6. For safety reasons, especially on the upper bunk bed, DO NOT allow rough
playing or jumping on the bed and do not allow playing or hiding under the
bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for
replacement parts.
9. Use of a nightlight may provide added safety precaution for a person using
the upper bunk.
10. Always use the guardrails on both long sides of the upper bunk. If the bunk
bed will be placed next to the wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. No more than one person is allowed on the upper bunk at all times.
13. The MAXIMUM weight capacity for the upper bunk is not to exceed 150 lbs.
WARNING:
STRANGULATION HAZARD
Never attach or hang objects to any part of the bunk bed
that are not designed for use with the bed. Objects such as
hanger, hook, belt, bag, rope, string, etc. should not be used
on or around the bunk bed.