Furniture of America CM7017Q User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7017Q
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-30
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench
(Not Included)

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 24 pcs
Bolt 5/16”x1-1/2”
#B x 24 pcs
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
#C x 24 pcs
Flat Washer
MD
#D x 13 pcs
Center Connector
Page 3 of 6
#H x 4 pcs
Hex Nut
#6 x 26 pcs
Slat
#4 x 2 pcs
Cushion
#5 x 1 pc
Support Rail
#7 x 2 pcs
Support Rail Leg
#E x 26 pcs
End Cap
#F x 1 pc
Allen Wrench
#G x 1 pc
Wrench
#I x 4 pcs
Corner Bracket
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage.

Page 4 of 6
Remove the cushions (#4) and the slats (#6) from behind the zipper of the
back of the headboard (#1).
#A x 4 pcs
#B x 4 pcs
#C x 4 pcs
#H x 4 pcs
Turn right (clockwise) to tighten
I. Align the 2 support rail legs (#7) with the pre-drilled holes of the support rail
(#5).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#B) onto the
bolt (#A) and then the flat washer (#C) onto the SAME bolt (#A), in that
order.
III. Insert the bolt assemblies through the pre-drilled holes of the support rail
(#5) and the 2 slat support legs (#7) using the Allen wrench (#F).
IV. Tighten the 4 hex nuts (#H) onto the same bolts (#B) using the wrench (#G)
to secure the parts together.
Adjust the levelers on Step 5.

Turn right (clockwise) to tighten
Page 5 of 6
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#I x 4 pcs
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Align the 2 corner brackets
(#I) assembled on the 2 side
rails (#2) with the pre-drilled
holes on the right and left side
of the headboard (#1).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#B) onto the bolt (#A)
and then the flat washer (#C)
onto the SAME bolt (#A), in
that order.
III. Insert the bolt assemblies
through the holes of the 2
corner brackets (#I) using the
Allen wrench (#F) to lock them
with the right and left side of
the headboard (#1).
IV. Repeat the process above to
assemble the other 2 corner
brackets (#I) on the other ends
of the 2 side rails (#2) onto
the footboard (#3).
Turn right (clockwise) to tighten
I. Align the round holes of the
2 corner brackets (#I) with
the pre-drilled holes of the
side rail (#2).
II. Prepare 4 bolt assemblies
by inserting FIRST the lock
washer (#B) onto the bolt
(#A) and then the flat
washer (#C) onto the SAME
bolt (#A), in that order.
III. Insert the bolt assemblies
through the round holes of
the 2 corner brackets (#I)
and secure those bolts using
the Allen wrench (#F) to lock
them with the side rail (#2).
IV. Repeat the process above to
assemble the remaining 2
corner brackets (#I) onto the
other side rail (#2).

Page6of6
I. Align the assembled support rail (#5) with the pre-drilled holes on the center
of the headboard (#1) and the footboard (#3).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#B) onto the
bolt (#A) and then the flat washer (#C) onto the SAME bolt (#A), in that
order.
III. Insert the bolt assemblies through the brackets of the support rail (#5) using
the Allen wrench (#F) to lock them with the headboard (#1) and the
footboard (#3).
#A x 4 pcs
#B x 4 pcs
#C x 4 pcs
Turn right (clockwise) to tighten
#D x 13 pcs
#E x 26 pcs
I. Prepare a bed slat using two slats
(#6), one center connector (#D)
and two end caps (#E). See
diagram for the correct sequence
in connecting those parts.
II. Align the two end caps (#E) with
the pre-drilled holes on each side
of the side rails (#2) and press
firmly down on both end caps (#E)
to lock with the side rails (#2).
Then press firmly down on the
center connector (#D) to lock with
the support rail (#5).
III. Repeat the process above to
assemble the remaining bed slats
onto the side rails (#2) and the
support rail (#5).
IV. Place the 2 cushions (#4) onto the
headboard (#1).
V. Make sure the bed is rested on a
flat surface and does not feel
loose or wobbly. If it does, double
check that the bolts/screws are
secured and properly tightened.
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails.
ASSEMBLY IS COMPLETED
Adjust the levelers according to
the ground level. To lower or to
raise the slat support legs, turn
the leveler clockwise or
counterclockwise, respectively.

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7017CK/EK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-30
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench
(Not Included)

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 32 pcs
Bolt 5/16”x1-1/2”
#B x 32 pcs
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
#C x 32 pcs
Flat Washer
MD
#D x 26 pcs
Center Connector
Page 3 of 6
#H x 8 pcs
Hex Nut
#6 x 39 pcs
Slat
#4 x 2 pcs
Cushion
#5 x 2 pcs
Support Rail
#7 x 4 pcs
Support Rail Leg
#E x 26 pcs
End Cap
#F x 1 pc
Allen Wrench
#G x 1 pc
Wrench
#I x 4 pcs
Corner Bracket
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage.

Page 4 of 6
Remove the cushions (#4) and the slats (#6) from behind the zipper of the
back of the headboard (#1).
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#H x 8 pcs
Turn right (clockwise) to tighten
I. Align the 2 support rail legs (#7) with the pre-drilled holes of the support rail
(#5).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#B) onto the
bolt (#A) and then the flat washer (#C) onto the SAME bolt (#A), in that
order.
III. Insert the bolt assemblies through the pre-drilled holes of the support rail
(#5) and the 2 slat support legs (#7) using the Allen wrench (#F).
IV. Tighten the 4 hex nuts (#H) onto the same bolts (#B) using the wrench (#G)
to secure the parts together.
V. Repeat the process above to assemble the remaining two support rail legs
(#7) onto the other support rail (#5).
Adjust the levelers on Step 5.
X 2