Furniture of America CM3776SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-02-28
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3776SC-2PK

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Back Rest w/ Legs
#2 x 1 pc
Seat Cushion Frame
#3 x 2 pcs
Front Leg
#A x 11 pcs
Flat Washer 1/4”
#B x 11 pcs
Lock Washer 1/4”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 3 pcs
Bolt 1/4”x1-1/2”
MD
#D x 4 pcs
Bolt 1/4”x2-3/8”
Page 3 of 5
#E x 4 pcs
Bolt 1/4”x3”
#F x 1 pc
Allen Wrench
Note: The above parts and hardware are shown for a
complete assembly of ONE chair. However, the actual
parts and hardware (with an exception of the Allen wrench)
in the box will be twice the quantities due to the packaging
of TWO chairs in a box.
X 2

Step 1 I. Place the back rest with legs (#1) on a protected surface.
II. Align the seat cushion frame (#2) with the pre-drilled holes of the
back rest with legs (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer (#B)
onto the bolt (#C) and then the flat washer (#A) onto the SAME bolt
(#C), in that order.
IV. Insert the bolt assembly through the center hole of the seat cushion
frame (#2) and secure that bolt using the Allen wrench (#F) to lock it
in with the back rest with legs (#1). Repeat for the other two holes.
Step 2
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 4 of 5
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
#A x 4 pcs
#B x 4 pcs
#E x 4 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#B)
onto the bolt (#E) and then the flat washer (#A) onto the SAME bolt
(#E), in that order.
II. Insert 2 bolt assemblies through the two pre-drilled center holes in
the corner of the seat cushion frame (#2) and secure those bolts
using the Allen wrench (#F) to lock it in with the back rest with legs
(#1). Repeat for the other side.
Enlarged
Enlarged

Step 3 I. Insert the front leg (#3) to align with the pre-drilled holes of the seat
cushion frame (#2).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#B)
onto the bolt (#D) and then the flat washer (#A) onto the SAME bolt
(#D), in that order.
III. Insert the 2 bolt assemblies through the two pre-drilled center holes
in the corner of the seat cushion frame (#2) and secure those bolts
using the Allen wrench (#A) to lock it in with the front leg (#3).
Repeat for the other side.
IV. Carefully turn the completed chair upright. Make sure the chair is
rested on a flat surface and it does not feel loose or wobbly. If it
does, double check that the bolts are secured and properly tighten.
Turn right (clockwise) to tighten
Page 5 of 5
#A x 4 pcs
#B x 4 pcs
#D x 4 pcs
Enlarged
ASSEMBLE EVERYTHING EXACTLY
THE SAME FOR THE SECOND CHAIR
#2
ASSEMBLY IS COMPLETED