Furniture of America CM-BK1042 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-04
Page 1 of 13
DIFFICULT
ASSEMBLY RATING
CM-BK1042
2 PERSONS RECOMMENDED

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 13

Page 3 of 13

Parts List
Page 4 of 13
#4 x 1 pc
Right Lower Guardrail
#1 x 1 pc
Left Top Panel
#3 x 1 pc
Left Lower Guardrail
#7 x 1 pc
Left Upper G/R Side
#9 x 4 pcs
Outer Bed Frame
#6 x 1 pc
Upper Headboard
#10 x 4 pcs
Inner Bed Frame
#2 x 1 pc
Right Top Panel
#5 x 1 pc
Lower Headboard
#8 x 1 pc
Right Upper G/R Side
#11 x 1 pc
Lower Footboard
#13 x 2 pcs
Handle #14 x 1 pc
Front Round Panel B
#12 x 1 pc
Bottom Front Panel
#15 x 1 pc
Front Round Panel C #16 x 1 pc
Upper Footboard
Before you begin, please read Page 3
for “Assembly and Care Advice” AND
Page 13 for “Safety Warnings”.
And remember, do not tighten until
each step is completed or instructed.

Parts List (Continued)
Page 5 of 13
#17 x 1 pc
Ladder #18 x 2 pcs
Rear Wheel
#19 x 2 pcs
Front Wheel A #20 x 2 pcs
Sign
#21 x 1 pc
Right Front Post #22 x 1 pc Left Front Post
#23 x 2 pcs
Rear Post #24 x 1 pc
Front Round Panel A
#25 x 2 pcs
Front Wheel B #26 x 4 pcs
Headlight
Note: Right and left are determined
by facing the front end of the bunk
bed in its upright position.

Hardware List
Page 6 of 13
#D x 7 pcs
Bolt M6x30
#A x 11 pcs
Bolt M6x8
#C x 50 pcs
Bolt M6x25
#G x 2 pcs
Bolt M6x50
#I x 24 pcs
Front Lug Nut
#F x 2 pcs
Bolt M6x45
#J x 9 pcs
Rear Lug Nut
#B x 3 pcs
Bolt M6x15
#E x 20 pcs
Bolt M6x35
#H x 4 pcs
Bolt M6x65
#K x 8 pcs
Threaded Stud (S)
#M x 3 pcs
Barrel Nut #N x 2 pcs
Allen Wrench
#L x 6 pcs
Threaded Stud (L)
#O x 16 pcs
Bolt M6x65 #P x 8 pcs Spacer
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.

Page 7 of 13
Turn right (clockwise) to tighten

Page 8 of 13
Turn right (clockwise) to tighten

Page 9 of 13
Turn right (clockwise) to tighten

Page 10 of 13
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

Page 11 of 13
Turn right (clockwise) to tighten

Page 12 of 13
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
Turn right (clockwise) to tighten
Safety is ALWAYS
the main priority.
For extra safety
measure and before
using the bed,
please take the time
to inspect the
assembly again and
make sure that ALL
bolts and screws
are FULLY
tightened. Read and follow the information on the
WARNINGS shown on the end structure of
the upper bunk and on the carton. Do not
remove warning label from the bed. Keep
these instructions for future reference.

Page 13 of 13
Safety Warnings for Bunk Beds
1. Read and follow the information on the WARNINGS shown on the end
structure of the upper bunk and on the carton. Do not remove warning label
from the bed. Keep these instructions for future reference.
2. Always use the recommended size mattress or mattress support, or both, to
help prevent the likelihood of entrapment or falls. The proper mattress sizes
for the UPPER TWIN-SIZE bunk should be 74” to 75” long x 37½” to 38½”
wide x 6” high (no higher than 6”) and for the LOWER TWIN-SIZE bunk
should be 74” to 75” long x 37½” to 38½” wide x 6” to 8” high.
3. Surface of mattress must be at least 5 inches (127 mm) BELOW the upper
edge of guardrails.
4. Do not allow persons under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrails, ladder, handle and other
components are in their proper position, free from damage, and that all
connectors are tighten and secured.
6. For safety reasons, especially on the upper bunk bed, DO NOT allow rough
playing or jumping on the bed and do not allow playing or hiding under the
bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for
replacement parts.
9. Use of a nightlight may provide added safety precaution for a person using
the upper bunk.
10. Always use the guardrails on both long sides of the upper bunk. If the bunk
bed will be placed next to the wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. No more than one person is allowed on the upper bunk at all times.
13. The MAXIMUM weight capacity for the upper bunk is not to exceed 150 lbs.
WARNING:
STRANGULATION HAZARD
Never attach or hang objects to any part of the bunk bed
that are not designed for use with the bed. Objects such as
hanger, hook, belt, bag, rope, string, etc. should not be used
on or around the bunk bed.