Furniture of America CM-BK611 User manual

For more information contact our team: [email protected]

Hardware List
#H x 41pcs
#I x 10pcs
#J x 6pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#Q x 4pcs
Page 6 of 17
Bolt 1/4" x 1-3/8"
Screw 1/8" x 5/8"
#P x 5pcs
Screw 3/16" x 3/4"
Screw 1/8" x 1/2"
#K x 14pcs
#L x 20pcs
#N x 5pcs
#G x 40pcs
Screw 3/16" x 1"
#O x 5pcs
#M x 1pc
Allen Wrench
Metal Dowel 3/8"x3-9/16"
Wood Dowel 7/16"x1-9/16"
Wood Dowel 1/4"x1-3/16"
Scroll Bar
Scroll Bar
#R x 5pcs
Iron Basin

1. Align the side rails (#7) to the holes
along the lower end guardrails (#1,3),
then insert 2 barrel nuts (#C) into the
holes along the sides of the side rails (#7).
2. Face the holes on
the barrel nut (#C)
towards the hole,
then insert 2 bolts
(#A) into the holes
along the end
guardrails (#1,3).
Insert the bolts
into the barrel
nuts and secure
using the Allen
wrench (#M)
1. Insert a wood dowel (#K) into the bottom holes along the
ends of the guardrails (#8), then insert those ends into the
holes along the sides of the end guardrails (#2,4). Insert
the screw (#B) into each end. Secure using the Allen wrench.
2. Align the side rails (#7) to the holes
along the upper end guardrails (#2,4),
then insert 2 barrel nuts (#C) into the
holes along the sides of the side rails (#7).
3. Face the holes on
the barrel nut (#C)
towards the hole,
then insert 2 bolts
(#A) into the holes
along the end
guardrails (#2,4).
Insert the bolts
into the barrel
nuts and secure
using the Allen
wrench (#M)

Align the guardrail support (#12) to the center holes along
the side rails (#7) and guardrails (#8), then insert 3 screws
(#F) into each. Secure using a Phillips screwdriver.
Insert the metal dowels (#J)
into the holes along the top
of the bottom bed, then
carefully place the top bed
onto those metal dowels.

1. Align the foot plates
as displayed.
2. Insert bolts (#D) into the holes
along the sides of (#16,17). Secure
using the Allen wrench (#M).
3. Insert bolts (#E) into the holes
along the side of (#13). Secure
using the Allen wrench (#M).
2. Insert bolts (#E)
into the holes along
the side of (#13).
Secure using the
Allen wrench (#M).
1. Align the lower end guardrail (#5)
to the foot plates, then insert the
bolts (#D) into the holes along the
plates. Secure using the Allen wrench.

1. Insert a wood dowel (#K) into the bottom holes along the ends of the back guard-
rails (#9), then insert those ends into the holes along the side of the end guardrails
(#4). Insert the screws (#B) into each end. Secure using the Allen wrench.
2. Insert bolts (#Q) into the holes
along the side of (#18). Secure
using the Allen wrench (#M).
1. Apply wood dowels (#K) into the holes
along the ends of the guardrails (#9).
#J
2. Place the
dowels (#J)
into the holes
then place the
guardrail (#6).
3. Insert the dowels into the guardrail (#6),
then insert 3 screws (#B) and secure.
4.
5.

Page 12 of 17
#F x 5pcs
#O x 5pcs
#P x 5pcs
#H x 10pcs
#R x 5pcs
#G
#G x 20pcs
#L x 20pcs
#23,#32
#22,#31
#24,#25
#26,#33
#19,#20
#21,#30
#L
#L
X5
#P
#F
#O
#R
#H
1. Insert the wood dowels (#L) into the holes along (#19,20,21,30),
then place (#22,23,31,32) onto the other ends of those dowels.
2. Insert the screws (#G) into each hole. Secure using a screwdriver.
3. Slide (#24,25,26,33) along
the ridges of each drawer.
Place the scroll bars (#O), then
insert a screw (#P) into each end.
Secure using a Phillips screwdriver.
Place iron basin (#R) to the back of each scroll bar (#O).
Secure with screws (#H).

Align (#27,28,39,34) to the back of the
drawers, then insert the screw (#G) into
each hole. Secure using a screwdriver.
Place the scroll bars (#N) onto the bottom of the drawers
and align the holes. Insert the screw (#H) into the front hole
and 2 screws (#I) into the rear holes. Secure using a screwdriver.

Align (#37,38,39,40), then insert
the screws (#H) into the holes.
Secure using a screwdriver.

Align the wood connection (#35)
to the top step and wood
connections (#36) to the other
two. Insert 2 bolts (#E) into each.
Secure using the Allen wrench (#M).
Insert the drawers
accordingly.

Place the twin slat kit (#11)
onto the top bunk. Insert
the screws (#F) into each
hole and secure using
a Phillips screwdriver
Place the full slat kit (#10)
onto the bottom bunk.
Insert the screws (#F) into
each hole and secure using
a Phillips screwdriver