Furniture of America CM7060IV-F User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7060IV-F/Q
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-19
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED

Page 2 of 6

Parts List
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the area
of its intended location. Make sure you have enough space to
move around during the assembly. ALWAYS have at least two
people to help with transporting and assembling of the product
and to avoid any potential injury and/or damage.
MD
Page 3 of 6
Hardware List

Step 1
I. Prepare 4 bolt assemblies by inserting
FIRST the lock washer (#E) onto the
bolt (#A) and then the flat washer (#D)
onto the SAME bolt (#A), in that order.
II. Insert two bolt assemblies through each
side of the pre-drilled holes of the
headboard (#1) using theAllen wrench
(#H) but expose about ½” of the bolts’
threads.
III. Mount the brackets of the side rails (#2)
onto the bolts (#A) on each side of the
headboard (#1). Make sure all the
washers are in the FRONT of the
brackets. Use the Allen wrench (#H) to
tighten the bolts with the two parts
together.
IV. Repeat the process I through III above
to assemble the other ends of the side
rails (#2) onto the footboard (#3).
Step 2
Turn right (clockwise) to tighten
Page 4 of 6
Enlarged
Enlarged
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. Align the foot (#5) onto the pre-drilled holes on the bottom corner of the
headboard (#1).
II. Prepare two bolt assemblies by inserting FIRST the lock washer (#E)
onto the bolt (#C) and then the flat washer (#D) onto the SAME bolt
(#C), in that order.
III. Insert the bolt assemblies through the holes of the foot (#5) and secure
those bolts using the Allen wrench (#H) to lock them in with the
headboard (#1). Repeat the assembly for the other foot (#5) to the
other side of the headboard (#1).
IV. For the assembly of the feet (#5) to the footboard (#3), repeat the
process I through III of the above.
Turn right (clockwise) to tighten
#A x 8 pcs
#E x 8 pcs
#D x 8 pcs

Step 3
Step 4
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 5 of 6
Enlarged
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Align the two slat support legs (#7) with the pre-drilled holes of the
central support rail (#4).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#E) onto
the bolt (#B) and then the flat washer (#D) onto the SAME bolt (#B), in
that order.
III. Insert the two bolt assemblies through the pre-drilled holes of the central
support rail (#4) using the Allen wrench (#H) to lock them in with the slat
support legs (#7)
Adjust the leveler according to the ground
level. To lower or to raise the slat support
leg, you need to turn the leveler clockwise
or counterclockwise, respectively.
I. Align the central support rail
(#4) with the pre-drilled
holes on the center of the
headboard (#1) and the
footboard (#3). Prepare 4
bolt assemblies by inserting
FIRST the lock washer (#E)
onto the bolt (#B) and then
the flat washer (#D) onto
the SAME bolt (#B), in that
order.
II. Insert the 4 bolt assemblies
through the brackets of the
central support rail (#4)
using the Allen wrench (#H)
to lock them in with the
headboard (#1) and the
footboard (#1).
Enlarged
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs