Furniture of America CM3122SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-05-16
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3122SC-2PK
Phillips Screwdriver
(Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
#A x 4 pcs x 2
Bolt 5/16”x3”
#B x 4 pcs x 2
Bolt 5/16”x2-3/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 1 pc x 2
Bolt 5/16”x1-9/16”
MD
#D x 9 pcs x 2
Flat Washer
#4 x 2 pcs x 2
Leg Support
Page 3 of 5
#E x 9 pcs x 2
Lock Washer
#F x 1 pc
Allen Wrench
#G x 4 pcs x 2
Screw
Note: The above parts and hardware are shown for a complete
assembly of ONE chair. However, the actual parts and hardware
(with an exception of the Allen wrench) in the box will be twice
the quantities listed to include the assembly of the second chair.
X 2

I. Place the backrest with legs
(#1) on a protected surface.
Align the seat (#2) with the
pre-drilled holes of the
backrest with legs (#1).
II. Prepare a bolt assembly by
inserting FIRST the lock
washer (#E) onto the bolt
(#C) and then the flat
washer (#D) onto the SAME
bolt (#C), in that order.
III. Insert the bolt assembly
through the center hole of
the seat (#2) and secure
that bolt using theAllen
wrench (#F) to lock it in with
the backrest with legs (#1).
Turn right (clockwise) to tighten
Page 4 of 5
I. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#E) onto the bolt (#A) and then
the flat washer (#D) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies
through the pre-drilled holes in
the corners of the seat (#2) and
secure those bolts using the
Allen wrench (#F) to lock them
in with the backrest with legs
(#1).
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
#C x 1 pc
#D x 1 pc
#E x 1 pc

I. Align the two legs (#3) with
the pre-drilled holes of the
seat (#2).
II. Prepare 4 bolt assemblies
by inserting FIRST the lock
washer (#E) onto the bolt
(#B) and then the flat
washer (#D) onto the SAME
bolt (#B), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes
in the corners of the seat
(#2) and secure those bolts
using the Allen wrench (#F)
to lock them in with the legs
(#3).
Page 5 of 5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR.
Turn right (clockwise) to tighten
I. Insert the leg supports (#4) into
the backrest with legs (#1)AND
the front legs (#3).
II. Secure the leg supports (#4) with
4 wood screws (#G) using a
Phillips screwdriver to lock them
with in the backrest with legs (#1)
AND the front legs (#3).
III. Carefully turn the completed chair
upright. Make sure the chair is
rested on a flat surface and it
does not feel loose or wobbly. If
it does, double check that the
bolts are secured and properly
tighten.
#G x 4 pcs
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
#2
#1
#3