Furniture of America CM3455T User manual

EASY DIFFICULT
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3455T
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Page 1 of 9 Rev: 18-04-16
For more information contact our team: [email protected]
Assembly Instructions
Wrench
(Included)

Page 2 of 9
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 9
Table Top
#1 x 1pc
#3 x 2pcs
#4 x 2pcs
Allen Wrench 4mm
#D x 1pc
Bolt Ø5/16" x 1-1/2"
#A x 24pcs
Bolt Ø5/16" x 4"
#E x 6pcs
#C x 30 pcs
Lock Washer Ø5/16"
#B x 30pcs
Lock Nut Ø5/16"
#F x 6pcs
#5 x 4pcs
Table Leaf
#2 x 1pc
#6 x 2pcs
Mounting Plate 1
#7 x 2pcs
Mounting Plate 2
Leg
Curve Washer
#G x 6pcs
Side Support Bar
Middle Support Bar
Flat Washer Ø5/16"

#H x 8pcs
Bolt Ø1/4" x 1-1/2"
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 9
#I x 8pcs
#J x 8pcs
Wrench 1/2"
#K x 1pc
Flat Washer Ø1/4"
Lock Washer Ø1/4"
#5
#5
#5
#6
#6
#7
#4
#4
#1
#2
#3
#3
#5

#E x 2pcs
Page 5 of 9
#B x 2pcs
#C x 2pcs
#F x 2pcs
#G x 2pcs
#E
#6
#E
#5
#6
#5
#5
#G #C
#B #F
#K
x 4
x 2
x 2
Attach bolts (#E) to the hole of each legs (#5) and side support bars (#6).
Align legs (#5) to the side support bar (#6). Insert curved washer (#G), flat washer (#C),
lock washer (#B), then hex nut (#F) onto the bolts of the legs (#5).

Page 6 of 9
#A x 4pcs
#B x 4pcs
#C x 4pcs
#4
#D
#A
#B
#C
#7
#B x 2pcs
#C x 2pcs
#F x 2pcs
#G x 2pcs
#G
#C
#B
#F
#K
x 2
#6
Prepare 4 bolts assembly by inserting
lock washer (#B), then flat washer (#C)
onto bolts (#A). Align mounting plate
(#4) to the holes of the legs. Secure by
using bolts (#A).
Align middle support bar (#7) to the bolts of the side support bars (#6). Insert curved washer (#G),
flat washer (#C), lock washer (#B), then hex nut (#F) onto the bolts of the side support bars (#6).

Page 7 of 9
#H x 8pcs
#I x 8pcs
#J x 8pcs
#H
#I
#J
#D
#A
#B
#C
#D
#A x 16pcs
#B x 16pcs
#C x 16pcs
#5
#4
#3
#3
#1
#3
Prepare 8 bolts assembly by inserting lock washer (#I),
then flat washer (#J) onto bolts (#H). Align mounting
plate (#3) to the holes of the table top (#1). Secure by
using bolts (#H).
Prepare 16 bolts assembly by inserting lock washer (#B), then flat washer (#C) onto bolts (#A).
Align legs to the table top (#1). Secure by using bolts (#A).

Page 8 of 9
#2
OPEN
Turn lever at the bottom of the table to open to extend table.
Place table leaf (#2) to the middle of the extended table.

Page 9 of 9
LOCK
ASSEMBLY IS COMPLETED
Turn lever to lock to secure leaf.