Furniture of America CM3720PT-3PK User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3720PT-3PK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
Rev: 19-07-11

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
Page 3 of 7
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#1 x 1pc x 2
Seat
#2 x 2pcs x 2
Right Leg
#3 x 2pcs x 2
Left Leg
#4 x 4pcs x 2
Stretcher
#5 x 1pc
#6 x 1pc
#7 x 1pc
#8 x 1pc
Table Top
Front Leg (Left )
Front Leg (Right)
Back Leg (Left )
Bolt Ø1/4" x 2"
#B x 2pcs
#C x 20pcs
#D x 24pcs
#E x 24pcs
Lock Washer Ø1/4"
Flat Washer Ø1/4"
#F x 2pcs
Bolt Ø1/4" x 3"
Screw #8 x 38mm
#A x 24pcs
#G x 1pc
Allen Wrench M4
Nut Ø1/4

Parts List
Page 4 of 7
#9 x 1pc
#10 x 1pc
#11 x 2pcs
Back Leg (Right )
Long Stretcher
Short Stretcher
#5
#6
#7
#8
#9
#10
#11
#1
#2
#2
#3
#4
x 2

# A x 8pcs
#D x 8pcs
#E x 8pcs
Page 5 of 7
#E
#D
#A
#G
#1
#2
#3
#4
#C
#3
#2
#2
#3
#4
#3
#2
# C x 8pcs
x 2
x 2
Align legs (#2,3) with stretchers (#4) and seat (#1), then
secure legs (#2,3) to seat (#1) by using bolts (#A) with
washers (#D,E).
Secure stretchers (#4) on legs (#2,3)
by using screws (#C).

Page 6 of 7
#7
#6
#E
#D
#A
#G
#10
#5
#F
#B
#11
#9
#8
#6
#7
#E
#D
#A
#G
#G
# A x 4pcs
#D x 4pcs
#E x 4pcs
# A x 4pcs
#B x 2pcs
#D x 4pcs
#E x 4pcs
#F x 2pcs
Align long stretcher (#10) to table legs (#6,7), then
secure by using bolts (#B) with barrel nuts (#F).
Align table legs (#6,7) to
the table (#5), then secure
by using bolts (#A) with
washers (#D,E).
Align table legs (#8,9) to the table top and
stretchers (#11), then secure table legs
(#8,9) to table top by using bolts (#A) with
washers (#D,E).

Page 7 of 7
#C
# C x 4pcs
ASSEMBLY IS COMPLETED
#11
#11
Secure the stretchers (#11) by using screws (#C).