Furniture of America CM7008T User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7008T
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-10
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 2 pcs
Side Rail
#3 x 1 pc
Footboard
#A x 8 pcs
Bolt 5/16”x1”
#B x 8 pcs
Bolt 5/16”x4”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 16 pcs
Flat Washer
MD
#D x 16 pcs
Lock Washer
#4 x 13 pcs
Slat
Page 3 of 5
#E x 26 pcs
End Cap
#F x 1 pc
Allen Wrench
#5 x 4 pcs
HB/FB Leg
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.

Turn right (clockwise) to tighten
Page 4 of 5
#B x 8 pcs
#C x 8 pcs
#D x 8 pcs
I. Align the two HB/FB legs (#5) with the pre-drilled holes underneath the
headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#D) onto the
bolt (#B) and then the flat washer (#C) onto the SAME bolt (#B), in that
order.
III. Insert the bolt assemblies through the holes of the two HB/FB legs (#5) and
secure those bolts using the Allen wrench (#F) to lock them with the
headboard (#1).
IV. Repeat the process above to assemble the remaining two HB/FB legs (#5)
onto the footboard (#3).
Turn right (clockwise) to tighten
#A x 8 pcs
#C x 8 pcs
#D x 8 pcs
I. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#D) onto the bolt (#A)
and then the flat washer (#C)
onto the SAME bolt (#A), in
that order.
II. Insert the bolt assemblies
through the right and left side
of the pre-drilled holes of the
headboard (#1) using the Allen
wrench (#F) but expose about
½” of the bolts’ threads.
III. Mount the brackets on the side
rails (#2) onto the bolts (#A) on
each side of the headboard
(#1). Make sure all the
washers are in the FRONT of
the brackets. Use the Allen
wrench (#F) to further tighten
the bolts to secure the two
parts together.
IV. Repeat the process above to
assemble the other ends of the
two side rails (#2) onto the
footboard (#3).

#E x 26 pcs
Page 5 of 5
.
I. Prepare a complete bed slat by connecting two end caps (#E)
onto the ends of the slat (#4).
II. Align the two end caps (#E) with the pre-drilled holes on each
side of the side rails (#2) and press firmly down on both end
caps (#G) to lock with the side rails (#2).
III. Repeat the process above to assemble the remaining bed slats
onto the side rails (#2).
IV. Make sure the bed is rested on a flat surface and does not feel
loose or wobbly. If it does, double check that the bolts/screws
are secured and properly tightened.
ASSEMBLY IS COMPLETED
Note: The correct position of the slats should be
arcing UPWARD when placing on the rails.
#4
#2