Furniture of America CM7009CK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-09
Page 1 of 10
DIFFICULT
ASSEMBLY RATING
CM7009Q
2 PERSONS RECOMMENDED
Phillips Screwdriver
(Not Included)

Page 2 of 10

Parts List
Page 3 of 10
#4 x 1 pc
Center Support Rail
#1 x 1 pc
Headboard
#3 x 1 pc
Footboard
#7 x 3 pcs
Side Rail Support
#9 x 2 pcs
Side Rail Leg
#6 x 6 pcs
Drawer Sliding Rail
#10 x 3 pcs
S/R Support Leg
#2 x 2 pcs
Side Rail
#5 x 2 pcs
Center Support Leg
#8 x 4 pcs
HB/FB Leg
#11 x 30 pcs
Slat
#13 x 6 pcs
Drawer Right Side #14 x 6 pcs
Drawer Left Side
#12 x 6 pcs
Drawer Front
#15 x 6 pcs
Drawer Rear #16 x 6 pcs Drawer Bottom
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.

#D x 20 pcs
Flat Washer
Hardware List
#A x 8 pcs
Bolt 5/16”x1”
#C x 6 pcs
Bolt 5/16”x3”
#G x 30 pcs
End Cap
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage,
especially with the fragile nature of the mirror.
Page 4 of 10
#I x 72 pcs
Screw M8x1”
#F x 15 pcs
Center Connector
#J x 18 pcs
Screw M8x3/8”
#B x 6 pcs
Bolt 5/16”x1-3/4”
#E x 20 pcs
Lock Washer
#H x 1 pc
Allen Wrench
#K x 6 pcs
Screw M8x1-1/2”

Page 5 of 10
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Note: Right and left are determined by
facing the front of the drawer in its
upright position.
I. Align the drawer right side (#13) and the drawer left side (#14)
with the pre-drilled holes on the drawer front (#12).
II. Secure 3 screws (#I) each into the drawer right side (#13) and
the drawer left side (#14) using a Phillips screwdriver to tighten
them to the drawer front (#12).
III. Repeat the process above to assemble the remaining 5 drawers.
I. Insert the drawer bottom (#16) into the grooves.
II. Align the drawer rear (#15) with the pre-drilled holes on the
drawer right side (#13) and the drawer left side (#14).
III. Secure 3 screws (#I) each into the drawer right side (#13) and
the drawer left side (#14) using a Phillips screwdriver to tighten
them to the drawer rear (#15).
IV. Repeat the process above to assemble the remaining 5
drawers.
#I x 36 pcs
#I x 36 pcs
X 6
X 6

Page 6 of 10
Turn right (clockwise) to tighten
I. Align the drawer sliding rail (#6) with the pre-drilled holes on the
bottom of the drawer rear (#15) and the drawer front (#12).
II. Secure 3 screws (#J) into the drawer sliding rail (#6) using a
Phillips screwdriver to tighten them to the drawer rear (#15) and
the drawer front (#12).
III. Repeat the process above to assemble the remaining 5 drawers.
#J x 18 pcs X 6
I. Align the two HB/FB legs
(#8) with the pre-drilled
holes underneath the
headboard (#1).
II. Prepare two bolt assemblies
by inserting FIRST the lock
washer (#E) onto the bolt
(#C) and then the flat
washer (#D) onto the SAME
bolt (#C), in that order.
III. Insert the bolt assemblies
through the two HB/FB legs
(#8) using the Allen wrench
(#H) to lock them with the
headboard (#1).
IV. Repeat the process above
to assemble the other two
HB/FB legs (#8) onto the
footboard (#3).
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten

Page 7 of 10
Turn right (clockwise) to tighten
I. Align the two side rail legs (#9) with the pre-drilled holes
underneath the two side rails (#2).
II. Prepare 2 bolt assemblies by inserting FIRST the lock
washer (#E) onto the bolt (#C) and then the flat washer (#D)
onto the SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the two side rail legs (#9)
using the Allen wrench (#H) to lock them with the two side
rails (#2).
X 2
Turn right (clockwise) to tighten
I. Align the threaded end of the
side rail support leg (#10) with
the pre-drilled hole on the
center of the side rail support
(#7) and tighten by hand until
secured.
II. Repeat the process above to
assemble the remaining two
side rail support legs (#10)
onto the two side rail supports
(#7).
#C x 2 pcs
#D x 2 pcs
#E x 2 pcs
X 3

Page 8 of 10
Turn right (clockwise) to tighten
I. Align the two center support legs (#5) with the pre-drilled holes underneath
the center support rail (#4).
II. Prepare two bolt assemblies by inserting FIRST the lock washer (#E) onto
the bolt (#B) and then the flat washer (#D) onto the SAME bolt (#B), in that
order.
III. Insert the bolt assemblies through the center support rail (#4) using the
Allen wrench (#H) to lock them with the two center support legs (#5).
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#E) onto the
bolt (#A) and then the flat washer (#D) onto the SAME bolt (#A), in that order.
II. Insert 4 bolt assemblies into the pre-drilled holes of the headboard (#1) using
the Allen wrench (#H) but expose about ½” of the bolts’ threads.
III. Mount the brackets on the two side rails (#2) onto the bolts (#A). Make sure
the washers are in the front of the brackets. Use the Allen wrench (#H) to
tighten the bolts to secure the two side rails (#2) together with the headboard
(#1).
IV. Repeat the process above to assemble the other ends of the two side rails
(#2) onto the footboard (#3).
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
Turn right (clockwise) to tighten

Page 9 of 10
Turn right (clockwise) to tighten
I. Aligned the assembled side
rail support (#7) with the pre-
drilled holes on each side of
the side rails (#2).
II. Secure two screws (#K) into
each end of the side rail
support (#7) using a Phillips
screwdriver to tighten them
with the two side rails (#2).
III. Repeat the process above to
assemble the remainder two
side rail supports (#7) onto
the two side rails (#2).
#K x 6 pcs
I. Align the assembled center
support rail (#4) with the pre-
drilled holes on the center of
the headboard (#1) and the
footboard (#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt (#B)
and then the flat washer (#D)
onto the SAME bolt (#B), in
that order.
III. Insert the 4 bolt assemblies
through the center support rail
(#4) using the Allen wrench
(#H) to lock them with the
headboard (#1) and the
footboard (#3).
Turn right (clockwise) to tighten
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs

Page 10 of 10
ASSEMBLY IS COMPLETED
I. Prepare a bed slat using two slats (#11), one center connector
(#F) and two end caps (#G). See diagram below for the correct
sequence in connecting those parts.
II. Align the end caps (#G) with the pre-drilled holes on each side of
the side rails (#2) and press firmly down on both end caps (#G)
to lock with the side rails (#2). Then press firmly down on the
center connector (#F) to lock with the center support rail (#4).
III. Repeat the process above to assemble the remaining bed slats
onto the side rails (#2) and the center support rail (#4).
IV. Insert the 6 assembled drawers into the designated area of the
side rails (#2).
V. Make sure the bed is rested on a flat surface and does not feel
loose or wobbly. If it does, double check that the bolts/screws
are secured and properly tightened.
Note: The correct position of the slats should be
arcing UPWARD when placing on the rails.
#F x 15 pcs
#G x 30 pcs
#2
#4
#12