Furniture of America CM7528EK User manual

AssemblyInstructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
CM7528EK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
For more information contact our team: [email protected]
AssemblyInstructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
CM7528CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
For more information contact our team: [email protected]
Rev: 18-12-12
Rev: 18-12-12
Allen Wrench (Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)
Allen Wrench (Included)
Phillips Screwdriver
Wrench
(Included)
(Not Included)

Page2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.
Page2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
#2 x 2pcs
#E x 1pc
#A x 6pcs
#C x 14pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page3 of 7
Headboard Leg(L&R)
Allen Key4mm
Bolt Ø5/16" x 2-3/8"
Lock Washer Ø5/16"
#D x 14pcs
Flat Washer Ø5/16"
#1 x 1pc
Headboard
#4 x4pcs
FootboardLeg
#6 x 2pcs
Side Rail
#7 x 4pcs
Slat
#8 x 8pcsØ1/4"
Support Leg193x30x30mm
#F x8pcs
#B x 8pcs
Bolt Ø5/16" x 2"
#3 x 1pc
Footboard
#5 x 3pcs Ø1/4"
FBSupport Leg124x30x30mm
Threaded StudØ5/16" x 3-1/2"
Half Moon
Ø5/16"
#G x 8pcs
Hex nutØ5/16"
#H x 8pcs
Parts List
Hardware List
#2 x 2pcs
#E x 1pc
#A x 6pcs
#C x 14pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page3 of 7
Headboard Leg(L&R)
Allen Key4mm
Bolt Ø5/16" x 2-3/8"
Lock Washer Ø5/16"
#D x 14pcs
Flat Washer Ø5/16"
#1 x 1pc
Headboard
#4 x4pcs
FootboardLeg
#6 x 2pcs
Side Rail
#7 x 4pcs
Slat
#8 x 8pcs Ø1/4"
Support Leg193x30x30mm
#F x8pcs
#B x 8pcs
Bolt Ø5/16" x 2"
#3 x 1pc
Footboard
#5 x 3pcs Ø1/4"
FBSupport Leg124x30x30mm
Threaded StudØ5/16" x 3-1/2"
Half Moon
Ø5/16"
#G x 8pcs
Hex nut Ø5/16"
#H x 8pcs

Page4 of 7
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Hardware List
#J x8pcs#I x1pc
Screw #8 x 32mm
Wrench 12mm
Page4 of 7
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Hardware List
#J x8pcs#I x1pc
Screw #8 x 32mm
Wrench 12mm
#1
#2L
#6
#3
#4
#5
#7
#8
#2R
#1
#2L
#6
#3
#4
#5
#7
#8
#2R

Page5 of 7
#A x 6pcs
#C x6pcs
#D x6pcs
#B x 8pcs
#C x8pcs
#D x8pcs
Page5 of 7
#A x 6pcs
#C x6pcs
#D x6pcs
#B x 8pcs
#C x8pcs
#D x8pcs
L
#2R
#2L
#1
#A
#E
#C
#D
#D
#C
#B
#E
#5
#3
#4
L
#2R
#2L
#1
#A
#E
#C
#D
#D
#C
#B
#E
#5
#3
#4
Align HB legs (#2R/L) to the headboard (#1), then
secure by using bolts (#A) with washers (#C,D).
Attach support leg (#5) to the footboard (#3), then adjust
the leveler on the support leg (#5) according to ground
level.
Align legs (#4) to the footboard (#3), then
secure by using bolts (#B) with washers
(#C,D).

Page6 of 7
#F x 8pcs
#G x 8pcs
#H x 8pcs
Page6 of 7
#F x 8pcs
#G x 8pcs
#H x 8pcs
#F
#G #H
#I
#1
#6
#6
#3
x 4
#8
#7
#F
#G #H
#I
#1
#6
#6
#3
x 4
#8
#7
Attach threaded studs (#F) to the headboard (#1) and footboard (#3), then align the
side rails (#6) to the threaded studs (#F) attached to the headboard (#1) and
footboard (#3). Secure by using hex nut (#H) with washers (#G).
Attach support legs (#8) to the slats (#7). Adjust the levelers on
the support legs (#8) according to ground level.

Page7 of 7
ASSEMBLY IS COMPLETED
#J x 8pcs
Page7 of 7
ASSEMBLY IS COMPLETED
#J x 8pcs
#J
#J
#6
#7
#6
#7
Align slats (#7) to the side rails (#6), then secure
by using screws (#J).