Furniture of America CM4401E User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-07-28
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM4401E

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List
#1 x 1 pc
Glass Top
#2 x 1 pc
Stand A
#3 x 1 pc
Stand B
#D x 18 pcs
Lock Washer
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
#C x 4 pcs
Bolt 5/16”x1-1/4”
Page 4 of 6
#E x 18 pcs
Flat Washer
Hardware List
#A x 6 pcs
Bolt 5/16”x1/2”
#B x 8 pcs
Bolt 5/16”x3/4”
#G x 2 pcs
Base Bracket
#H x 1 pc
Flat Bracket
#F x 1 pc
Allen Wrench
#4 x 1 pc
Base

Insert stand A (#2) through stand B (#3). Make
sure the cutouts are aligned with each other.
Turn right (clockwise) to tighten
Page 5 of 6
#B x 8 pcs
#D x 8 pcs
#E x 8 pcs
#G x 2 pcs
#H x 1 pc
I. Insert the flat bracket (#H) through the cutout on the stand A (#2) and align with the pre-drilled
holes on the stand B (#3).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#D) onto the bolt (#B) and then
the flat washer (#E) onto the SAME bolt (#B), in that order.
III. Insert the bolt assemblies through the holes on the flat bracket (#H) and secure those bolts
using the Allen wrench (#F) to lock them with the stand B (#3).
IV. Align the long sides of the two base brackets (#G) with the pre-drilled holes on the stand A (#2)
and the stand B (#3).
V. Prepare 6 bolt assemblies by inserting FIRST the lock washer (#D) onto the bolt (#B) and then
the flat washer (#E) onto the SAME bolt (#B), in that order.
VI. Insert the bolt assemblies through the holes on the base brackets (#G) and secure those bolts
using the Allen wrench (#F) to lock them with the standA(#2) and the stand B (#3).
#3
#2

I. Align the base (#4) with the pre-
drilled holes on the standA (#2)
and the stand B (#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#C) and then
the flat washer (#E) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through
the holes of the base (#4) and
secure those bolts using the Allen
wrench (#F) to lock them with the
standA (#2) and the stand B (#3).
Page 6 of 6
ASSEMBLY IS COMPLETED
#3 #2
I. Carefully place the glass top (#1)
facing down on a protected surface.
II. Align the short sides of the base
brackets (#G) assembled on the
stands with the pre-drilled holes on
the glass top (#1).
III. Prepare 6 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#A) and then the
flat washer (#E) onto the SAME bolt
(#A), in that order.
IV. Insert the bolt assemblies through
the holes of the base brackets (#G)
and secure those bolts using the
Allen wrench (#F) to lock them with
the glass top (#1).
V. Place the table in its upright
position. Make sure the table is
rested on a flat surface and does not
feel loose or wobbly. If it does,
double check that the bolts/screws
are secured and properly tightened.
#A x 6 pcs
#D x 6 pcs
#E x 6 pcs
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
#G
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten