Furniture of America FCI-138-4L User manual

Page 1 of 12 REV.14-10-21
FCI-138-4L FCI-138C11

Page 2 of 12

Page 3 of 12

Page 4 of 12

Page 5 of 12
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS

70 INCH TV STAND
ASSEMBLY INSTRUCTIONS MODEL # FCI-138-4L FCI-138C11
please keep for future reference PARTS LIST
HARDWARE LIST
A1PC
120PCS
DIMENSIONS :70.8"(W)*15.7"(D)*20"(H)
220PCS 370PCS 44PCS 53PCS 68PCS
72sets(8pcs) 816PCS
B1PC
I1PC
M1PC
9 10 1PC 11 8PCS8PCS
C1PC D1PC
E1PC F1PC
G1PC H2PCS
J4PCS K4PCS
L2PCS
N1PC
O2PCS
P2PCS
Q2PCS
R2PCS
12 8SETS
Page 6 of 12
A
F
M
N
BG
C

Dowel hole X2
STEP : 1
Hardware 1 x 8 pcs
Hardware 2 x 8 pcs
Hardware 3 x 4 pcs
Hardware 6 x 8 pcs
Hardware 7 x 4 pcs drawer rails
Hardware 8 x 8 pcs
ASSEMBLY INSTRUCTIONS
Page 7 of 12
Side View
Right Drawer Rail
Front View
Identifying Drawer's Rails (a.k.a. Runners, Glides, Slides or Guides)
An assembly of ONE drawer requires a set of 4 different rails: right panel rail, left panel rail, right
drawer rail and left drawer rail. To identify which rail belongs to which part, please read completely
first before assembling.
To Determine Right/Left Panel Rail: Place the panel rail flat on its back with the roller position on
the left hand side. If there are two holes above the roller and the other end is slightly downward angle
then it is the LEFT PANEL RAIL. If there are two holes below the roller and the other end is slightly
upward angle, then it is the RIGHT PANEL RAIL. The right and left panel rails are mirror image of
each other.If needed, label or separate each rail for easy identification.
To Determine Right/Left Drawer Rail: Place the drawer rail with the round and oval holes resting
flat on the surface with its roller on the right hand side. If the roller is facing the top, then it is the
LEFT DRAWER RAIL and if the roller is facing the bottom, then it is the RIGHT DRAWER RAIL. The
right and left drawer rails are mirror image of each other. If needed, label or separate each rail for
easy identification.
Mounting the Panel Rail: The panel rail is constructed to be mounted flat. Make sure the roller is
position on the front of the panel and the screw holes are aligned with the pre-drilled holes of the
panel.
Mounting the Drawer Rail: The drawer rail is constructed to be mounted on the side of the drawer.
Make sure the roller is position on the SIDE REAR of the drawer and the screw holes are aligned
with the pre-drilled holes on the side of the drawer.
X2

ASSEMBLY INSTRUCTIONS
STEP : 2
STEP : 3
Page 8 of 12
Hardware 7 x 4 pcs
Hardware 8 x 8 pcs
Hardware 3 x 20 pcs
STEP : 4

STEP : 5
STEP : 6
STEP : 7
ASSEMBLY INSTRUCTIONS
Hardware 3 x 12 pcs
Page 9 of 12
10

STEP : 9
STEP : 8
L
K
K
K
K
3
STEP : 10
3
ASSEMBLY INSTRUCTIONS
Page 10 of 12
Hardware 2 x 4 pcs
Hardware 11 x 8 pcs
Hardware 3 x 12 pcs