Furniture of America Pioneer CM7449CK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7449CK/EK
Phillips Screwdriver
(not Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-24
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Allen Wrench (Included)

Page 2 of 5

Parts List
#1 x 1 pc
Headboard
#2 x 1 pc
Footboard
#3 x 2 pcs
Side Rail
#D x 1 pc
Allen Wrench
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.
MD
#C x 8 pcs
Flat Washer
#4 x 2 pcs
Headboard Leg
Page 3 of 5
#E x 8 pcs
Screw
Hardware List
#5 x 4 pcs
Slat
#6 x 8 pcs
Slat Support Leg
#A x 8 pcs
Bolt 1/4”x2”
#B x 8 pcs
Lock Washer

Page 4 of 5
Insert the hooks of the two side rails (#3) into the slotted bars of
the headboard (#1) and footboard (#2). Make sure the parts are
properly secured.
I. Align the 2 headboard legs (#4) with the pre-drilled holes of the
headboard (#1).
II. Prepare 8 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the 2 headboard legs (#4)
using theAllen wrench (#D) to lock them with the headboard (#1).
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs

Turn right (clockwise) to tighten
Page 5 of 5
#E x 8 pcs
ASSEMBLY IS COMPLETED
1. Align the 4 assembled
slats (#5) with the pre-
drilled holes on the side
rails (#3).
2. Secure 2 screws (#E) onto
the ends of each
assembled slat (#5) using
a Phillips screwdriver to
tighten them with the side
rails (#3).
3. If needed, adjust the
levelers according to the
ground level. To lower or to
raise the slat support leg,
turn the levelers clockwise
or counterclockwise,
respectively.
I. Align the threaded end of the 2 slat support legs (#6) with
the pre-drilled holes on the slat (#5) and tighten by hand
until secured.
II. Repeat the process above to assemble the remaining 6
slat support legs (#6) onto the 3 remaining slats (#5).
Adjust the levelers according to the
ground level on Step 4.

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7449Q
Phillips Screwdriver
(not Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-29
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Allen Wrench (Included)

Page 2 of 5

Parts List
#1 x 1 pc
Headboard
#2 x 1 pc
Footboard
#3 x 2 pcs
Side Rail
#D x 1 pc
Allen Wrench
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.
MD
#C x 8 pcs
Flat Washer
#4 x 2 pcs
Headboard Leg
Page 3 of 5
#E x 6 pcs
Screw
Hardware List
#5 x 3 pcs
Slat
#6 x 3 pcs
Slat Support Leg
#A x 8 pcs
Bolt 1/4”x2”
#B x 8 pcs
Lock Washer

Page 4 of 5
Insert the hooks of the two side rails (#3) into the slotted bars of
the headboard (#1) and footboard (#2). Make sure the parts are
properly secured.
I. Align the 2 headboard legs (#4) with the pre-drilled holes of the
headboard (#1).
II. Prepare 8 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the 2 headboard legs (#4)
using theAllen wrench (#D) to lock them with the headboard (#1).
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs

Turn right (clockwise) to tighten
Page 5 of 5
#E x 6 pcs
ASSEMBLY IS COMPLETED
1. Align the 3 assembled
slats (#5) with the pre-
drilled holes on the side
rails (#3).
2. Secure 2 screws (#E)
onto the ends of each
assembled slat (#5) using
a Phillips screwdriver to
tighten them with the side
rails (#3).
3. If needed, adjust the
levelers according to the
ground level. To lower or
to raise the slat support
leg, turn the levelers
clockwise or
counterclockwise,
respectively.
I. Align the threaded end of the slat support leg (#6) with the
pre-drilled hole on the slat (#5) and tighten by hand until
secured.
II. Repeat the process above to assemble the remaining 2
slat support legs (#6) onto the remaining 2 slats (#5).
Adjust the levelers according to the
ground level on Step 4.