Furniture of America YNJ-2078C31 User manual

EASY DIFFICULT
1 / 21
MODEL #
Questions?
GIVE US A CALL: 1-888-980-5122
MON－FRI 8:30AM－5:30PM (PST)
TOOLS REQUIRED
ASSEMBLY RATING
Recommended
2 - People
The Assembly Rating is a
assemble a specific product.
level of effort needed to
5-point system showing the
VERSION # 22-03-09
YNJ-2078C31
Phillips
Screwdriver
(Not Included)
(Not Included)
Hammer

2 / 21
are all accounted for.

3 / 21

4 / 21
AND MAY CAUSE SERIOUS INJURY.
ASSEMBLY
CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Position each part correctly
and insert screws or bolts into
their respective holes.
Use the appropriate hand tools
or power tools for assembly.
Select steps, such as tightening
screws and/or bolts, may require
hand tools to avoid causing
damage during assembly.
Turn clockwise to tighten and
only tighten when step is
completed or when instructed
to do so.
Save the instructions and store
any supplied tools for later
maintenance.
After two weeks, check and
tighten any loose hardware and
repeat again every six months
thereafter.

5 / 21

P1PC
O1PC
N1PC
M1PC
L1PC
K1PC
J1PC
I1PC
H1PC
G1PC
F1PC
E1PC
D1PC
C1PC
B1PC
1PC
A
YNJ-2078C31
MINI BAR
PARTS
HARDWARE ACCESSORIES
6 / 21
122PCS 222PCS 44PCS 54PCS
71SET 82PCS 62PCS
316PCS
94PCS
A15 1SET
A14 1PC
A12 1PC
A13 1PC
A11 4PCS
1.25"
0.47"
0.75"
1.97"
0.59"
0.39"
0.75"
1PC
A10
1PC
A1
4PCS
A7
4PCS
A6 2PCS A8
5PCS
A3 1PC
A4
2PCS
A9
5PCS
A5
2PCS
A2
10 2PCS
11 2PCS 12 2SETS 13 4PCS 14 8PCS 15 1PC
16 6PCS
T1PC
S1PC
R1PC
Q1PC
0.63" 1"
1.75"
1.25"
0.5"
0.47" 1.5"
17 6PCS
V1PC
U1PC
W2PCS
H
J
T
S
C
E
K

7 / 21
GET READY
Please group boards as below.
Body
Door
Drawer
G1PC F1PC E1PC C1PC
I1PC D1PC B1PC1PC A
R1PC
Q1PC
J1PC T1PC
S1PC
V1PC
U1PC W2PCS
H1PC
P1PC
O1PC
N1PC M1PC L1PC K1PC

8 / 21
1
Hardware x18PCS
1
Hardware x2PCS
8
Hardware x4PCS
9
Hardware x2SETS
12
Hardware x4PCS
13
Hardware x4PCS
14
Rotate
How to rotate
1. Push the button inward and hold
2. Rotate the upper bracket to the other side
3. And then release the button
B
1
1
11
1
1
1
1
14 14
12
magnet
C
1
1414
12
1
1
1
1
11
1
1
1
magnet
8
9
9
Attach magnet to panel
(#B,C) by using screws
(#9). Make sure magnet
(#8) is facing the direction
of the arrow.
X2
left 12
13
13
Screw horizontal part (#12) with
lower bracket. Screw the vertical
part (#12) with upper bracket.
right 12 13
13
Screw horizontal part (#12) with
lower bracket. Screw the vertical
part (#12) with upper bracket.

9 / 21
2
Hardware x8PCS
3
Accessory x1PC
A12
Hardware x2PCS
10
Hardware x1SET
7
Hardware x2PCS
11
OPTIONAL
Apply a dab of glue
into dowel holes of
panels before
inserting dowels (#3).
3
A12
A
3
3
10
11
H
7
7
D
3
3
F
3
3
E
3
3

10 / 21
3
Hardware x4PCS
1
Hardware x8PCS
3
Accessory x1PC
A12
OPTIONAL
Apply a dab of glue
into dowel holes of
panels before
inserting dowels (#3).
3
A12
3
3
I
3
M
3
3
G
3
3
L
3
N
1
K
1
1
1