Furniture of America CM-BK1167 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-05-13
Page 1 of 11
DIFFICULT
ASSEMBLY RATING
CM-BK1167
2 PERSONS RECOMMENDED
Phillips Screwdriver (Not Included)

Page 2 of 11

Page 3 of 11
PARTS LIST

Page 4 of 11
HARDWARE LIST
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.

Before you begin, please read Page 2
of “Assembly and Care Advice” AND
Page 11 of “Safety Warnings”.
And remember, do not fully tighten all
bolts until assembly is completed.
Page 5 of 11
MD
STEP 1: FRAME ASSEMBLY
Note: Right and left is
determined by
standing in the FRONT
of the completed bed.
STEP 2: BASE FRAME/CROSS BAR 1 ASSEMBLY
Enlarged
Turn right (clockwise) to tighten
4 LOCATIONS
2 LOCATIONS

Page 6 of 11
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
STEP 3: GUARDRAILASSEMBLY
STEP 4: CROSS BAR 2 ASSEMBLY
Enlarged
4 LOCATIONS
3 LOCATIONS 3 LOCATIONS
2 LOCATIONS

Page 7 of 11
STEP 5: CROSS BAR AND CONNECTED BARASSEMBLY
STEP 6: DESK BOARD ASSEMBLY
4 LOCATIONS
2 LOCATIONS
4 LOCATIONS
4 LOCATIONS 5 LOCATIONS
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

Page 8 of 11
STEP 7: INSPECTING AND TIGHTEN OF BOLTS/SCREWS
STEP 8: PENCIL HOLDER ASSEMBLY
Safety is ALWAYS
the main priority.
Please take the
time to inspect
the assembly and
FULLY tighten
every bolts and
screws from Step
1 to Step 6.
Read and follow the information on the
WARNINGS shown on the end structure of
the upper bunk and on the carton. Do not
remove warning label from the bed. Keep
these instructions for future reference.

Page 9 of 11
STEP 9: BASKETASSEMBLY
STEP 10: BOARD ASSEMBLY

Page 10 of 11
Read and follow the information on the
WARNINGS shown on the end structure of
the upper bunk and on the carton. Do not
remove warning label from the bed. Keep
these instructions for future reference.
For extra safety measure and before using
the bunk bed, please take the time to
inspect the assembly again and make sure
that ALL bolts and screws are FULLY
tighten.
ASSEMBLY IS COMPLETED
STEP 11: INSPECT THE ASSEMBLY

Page 11 of 11
Safety Warnings for Bunk Beds
1. Read and follow the information on the WARNINGS shown on the end
structure of the upper bunk and on the carton. Do not remove warning label
from the bed. Keep these instructions for future reference.
2. Always use the recommended size mattress or mattress support, or both, to
help prevent the likelihood of entrapment or falls. The proper mattress size
for the UPPER TWIN-SIZE bunk should be 74” to 75” long x 37½” to 38½”
wide x 6” high (no higher than 6”).
3. Surface of mattress must be at least 5 inches (127 mm) below the upper
edge of guardrails.
4. Do not allow persons under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrails, ladder, handle and other
components are in their proper position, free from damage, and that all
connectors are tighten and secured.
6. For safety reasons, especially on the upper bunk bed, DO NOT allow rough
playing or jumping on the bed and do not allow playing or hiding under the
bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for
replacement parts.
9. Use of a nightlight may provide added safety precaution for a person using
the upper bunk.
10. Always use the guardrails on both long sides of the upper bunk. If the bunk
bed will be placed next to the wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. No more than one person is allowed on the upper bunk at all times.
13. The MAXIMUM weight capacity for the upper bunk is not to exceed 150 lbs.
WARNING:
STRANGULATION HAZARD
Never attach or hang objects to any part of the bunk bed
that are not designed for use with the bed. Objects such as
hanger, hook, belt, bag, rope, string, etc. should not be used
on or around the bunk bed.