Furniture Solutions ARCADIA 17ARC07WTA User manual

INSTRUCTION MANUAL
PRODUCT: ARCADIA 7PCE DINING
ITEM CODE: 17ARC07WTA
MADE IN CHINA
Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au
Arcadia Ext Table (sold separately)
Arcadia Dining Chair (sold separately)
Please retain these pages as they contain ps to maximize the lifeme of your furniture with a measured eort.
Properly caring for your furniture can help ensure that it looks great year aer year.
Important Noce: While every eort is made to use quality materials our products are limited in design for domesc use only
& are not suitable for commercial use.

PRE ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that
may damage the product
2. Take care when liing. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly
5. Keep all hardware parts and packaging out of reach of small children
6. Do not over ghten the screws and bolts as this may damage the threads
20
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2
For any assistance with assembly or missing parts please contact:
Place of purchase or Furniture Soluons on below
Customer Service (Australia) Phone– 1300794 188
Email– customerservice@furnituresoluons.com.au

EXTENSION DINING TABLE PARTS LIST
A: x 1
Rim & Glass
B: x 4
Long Bolt
C: x 4
Table Leg
D: x 4
Washer
E: x 4
Nut
F: x 4
Leg Cover
G: x 4
Leg Adjuster
H: x 1
Tool
ASSEMBLY STEP 1 –Fit Long Bolts
With the help of another person carefully lay rim & glass [A] upside down on a soft clean
surface IE: Blanket . Note take care of extension piece when moving table.
At each corner of rim & glass you will see a threaded hole take long bolt [B] insert into hole and
by hand seat thread correctly, then wind down till firm. Next take table leg [C] locate open end
of leg and slide over top of long bolt and seat long bolt thru hole at end of leg, ensure thread
end of blot protrudes thru hole. Repeat for all long bolts. Move to Step 2

ASSEMBLY STEP 2 –Fit Nuts to Long Bolts
Once all long bolts & Table legs are fitted. Take nut [E] with washer [D] and by hand fit nut to
long bolt end poking thru table leg. Ensure nut is seated correctly before tightening. Then take
tool [H] fit over nut and tighten nut till firm. Note do not overtighten as may cause damage to
threads. Repeat for all legs. Move to step 3
ASSEMBLY STEP 2 –Fit Leg Cover
You may need a rubber mallet or a hammer and block of soft wood. Take leg cover [F] aline
over hole in bottom of leg. Take note of diagram for positioning of leg adjuster [G] which is
already fitted in leg cover. Take your fist, rubber mallet or hammer with block of wood and
gently tap to fit leg cover, note stop when all corners are flat. Repeat for all legs.
Assembly complete. With the help of another person gently lift table into air and turn till feet
can touch the ground. Take care of extension piece when moving table. Go to operating
instruction

Operations of extension and leg adjuster.
When assembling table you may have noticed a knob with silver plunger x 2 on one side on
table. If not please look under table and locate. These are used as locks when table is not
extended. You will need to push to unlock before you can extend table one for each end, and
reverse when you close table. Note best you inform all whom in house hold may use table, as
undue stress on plunger may result in damage to fittings.
Leg adjuster is simply used to adjust height for unlevered surface wind in or out to suit your
area.
PRODUCT CARE & MAINTENANCE
Glass Maintenance
Glass used is tempered for your safety; best results are to use placemats & coasters to avoid scratching
surface. Keep dust free, with floating glass please lift and clean underside of glass with a soft clean cloth.
Use of normal glass cleaning product is permissible but please rinse surrounding areas with clean water
to avoid damage to wicker or paint on aluminium frame.
Aluminium Frame Information
The majority of frames are mainly produced from aluminium, with the main benefit being a light weight
product for easier use. Some designs require steel to be used in certain sections for added strength. While
aluminium is rust resistant, bare metal can show signs of oxidation (red film) this does not constitute
rust. Simply you are able to wipe or sand surface to remove oxidation mark.
Note you will need to touch up affected area with paint to stop from reoccurring. Steel itself has a lower
resistance to elements than aluminium and will show signs of rust as it ages. Limited exposure & mainte-
nance are best solutions for adding life to any furniture used in outside areas.
Aluminium Frame Maintenance
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean rinse off with
a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks.
Note when cleaning if you find scratches in paint please cover with a paint to prevent oxidation.
Textilene Sling Information
The Textilene sling is a synthetic material made from a mixture of fibres of polyester covered with a
sheath of PVC, able to withstand compressive stresses, strains, atmospheric agents and UV rays.
For Outside use properties of material have a proven track record, while still subject to fading strength
will remain even after colour starts to fade. Shelf life again depends on location & environment, regular
cleaning & storage for best results for longevity.
Textilene Sling Maintenance
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean rinse off with
a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks. Ensure not left wet for long periods
of time to avoid mould build up.

WARNING SAFETY & ADVICE
Please be aware materials used in your furniture are not impervious to neglect, acts of god, abuse, alcohol
spills, improper use of chemicals such as bleach or any solvent based product, products are limited in
design for residential use only and not suitable for commercial use.
Please be aware that heat generated from barbeques and heaters will have an adverse effect on
your furniture do not place furniture in close proximity to heat sources.
When moving tables, chairs, sofas or bench’s always lift off the floor never drag. Most tables would
require a 2 person lift doing so benefits yourself and furniture as dragging may cause damage to furniture
and or surface on flooring.
Do not stand on furniture for your own safety & for the sake of the furniture
Never strike glass
Never drag or lean back chair, sofa, benchers whilst sitting on them
Tables, chairs, sofas & benches are not work benchers please only use as intended.
Fitting; bolts, nuts & screws should be checked periodically to ensure they are still firm. Note do not over
tighten.
Please secure furniture during in climatic weather, as lightweight aluminium can become a projectile
Please be aware of staining fabric; Suntan oil, alcohol, juices & other chemical may do permanent
damage to your covering, should be cleaned immediately
General wear & tear on cushions, please rotate cushions were possible as filling will soften with use,
replacement cushion fillings can be purchased from local upholster if required in future.
General wear & tear fabrics, most synthetic fabric resist pilling but pilling can occur from transference
from other fabric that come in contact with material IE: Cotton clothing & or towels.
Do not allow children to play under tables
In summary outdoor furniture products require care to provide you with many years of use. Best results
are to combine maintenance and protection from environment + the use of an outdoor cover can give you
better result with least amount of effort.

1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation, chipping/
scratching, exposure to extreme heat/cold, mould/mildew, hardware corrosion, misuse of the
products & defects caused by failure in duty of care for the product in accordance with the
care instructions. Warranty only extends to original purchaser and is not transferable, except
when given as a gift.
Duty of care:
While every attempt is made to supply product using quality components there is always a
need from consumer to help ensure a long life of use for product.
*Proper use of item, only what it is designed to do.
*Regular maintenance and cleaning.
*Protecting product from the harsh environment: Pollution, mould, heat.
To extend the life of your outdoor furniture we recommend that furniture covers should be
used on furniture which is used in areas not protected from elements. Caution should be used
when using oils, lotions & other chemicals such as chlorine.
Instruction Manual –Have been written to suit individual materials used in construction,
please retain for future use for duty of care, assembly, parts & component sizing.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required
before proceeding with any claim. In the case of product defects providing photos may be
able to speed up processing of the claim. If missing parts please refer to assembly instructions
for identification of said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure”.