Furniture Solutions ARCADIA 17ARCB2SW User manual

1
INSTRUCTION MANUAL
PRODUCT: ARCADIA BALCONY 5 PC SETTING
ITEM CODE: 17ARCB2SW
MADE IN CHINA

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2
30
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2
For any assistance with assembly or missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone–1300794 188
Email–[e-mail]
Notice:
Ottoman & Side Table require Assembly.

3
PARTS LIST
OTTOMAN
Code Description QTY
A
FAJ18128
-1.OR
Ottoman
Rim 2
B
FAJ18128
-1.OL
Ottoman Leg
4
L
FAJ18128
-1.OC
Ottoman Cushion
2
H
FAJ18128
-1.HW
Bolt M6*20mm
16
I
FAJ18128
-1.HW
Washer M6
16
J
FAJ18128
-1.HW
Cover Cap
16
K
FAJ18128
-1.HW
Tool
1

4
PARTS LIST
SIDE TABLE
Code Description QTY
C
FAJ18128
-1.SR
Side Table Rim
1
B
FAJ18128
-1.SL
Side
Table Leg 2
L
FAJ18128
-1.SG
Glass
Panel 1
H
FAJ18128
-1.HW
Bolt M6*20mm
8
I
FAJ18128
-1.HW
Washer M6
8
J
FAJ18128
-1.HW
Cover Cap
8
K
FAJ18128
-1.HW
Tool
1

5
ASSEMBLY INSTRUCTIONS
OTTOMAN
ASSEMBLY
Please follow pre-assembly instruction on page.2.
As indicated by diagram below place ottoman rim [A] upside down, locate the predrilled holes in
both ottoman leg [B] and ottoman rim. Aline leg holes with rim holes, while a second person
holds leg in position, take bolt [H] together with washer [I], insert thru hole and by hand seat the
thread correctly by turning 2-3 times and pull back to ensure bolt has gripped. Do not tighten yet.
Repeat for second hole of leg. Now go to opposite side of leg and repeat same process. Now take
tool [K] and tighten all four (4) bolts. Note do not over tighten as you may cause damage to
threads. Then repeat process again for the other leg. Assembly complete. Please pick up item and
stand on its feet, place cushion on top

5
ASSEMBLY INSTRUCTIONS
SIDE TABLE
ASSEMBLY
Please follow pre-assembly instruction on page.2.
As indicated by diagram below place side table rim [c] upside down, locate the predrilled holes in
both side table leg [D] and side table rim. Aline leg holes with rim holes, while a second person
holds leg in position, take bolt [H] together with washer [I], insert thru hole and by hand seat the
thread correctly by turning 2-3 times and pull back to ensure bolt has gripped. Do not tighten yet.
Repeat for second hole of leg. Now go to opposite side of leg and repeat same process. Now take
tool [K] and tighten all four (4) bolts. Note do not over tighten as you may cause damage to
threads. Then repeat process again for the other leg. Assembly complete. Please pick up item and
stand on its feet, place glass panel [E] as indicated in diagram,

7
COMPONENTS LIST
Left Hand Facing
Chair frame
Code: FAJ18128-1.LF
Left Hand Facing
Chair frame
Code: FAJ18128-1.RF
Chair Seat Cushion
Code: FAJ18128-1.SC
Chair Seat Cushion
Code: FAJ18128-1.SC
Chair Seat Cushion
Code: FAJ18128-1.BC
Chair Seat Cushion
Code: FAJ18128-1.BC

7
CONFIGURATION
Please note due to modular natural of this product you
have the ability to arrange to suit please see a couple
of examples below

6
PRODUCT CARE & MAINTENANCE
Fabric Information
Fabrics used in outdoor product are not made of any special type of material;
they do however use blends of common materials such as polyester, olefin &
acrylic which perform best for intended purpose. These fabrics are not
impervious to fading or mould, ensure cushions are always dry and put away
when not in use.
Fabric Maintenance
It is important to keep fabric free of dust and or debris. Please vacuum at least
every 2-3 weeks. Spot cleaning warm water & soft soap solution, sponge onto
affected area till clean rinse area with clean sponge, pat dry with a soft clean
cloth. Stubborn stains may be removed with fabric cleaner or if available steam
cleaning is ok providing covers are left on filling and on gentle setting. Note do
not use solvents, do not machine wash, do not tumble dry.
Textilene Sling Information
The Textilene sling is a synthetic material made from a mixture of fibres of polyester covered
with a sheath of PVC, able to withstand compressive stresses, strains, atmospheric agents and
UV rays.
For Outside use properties of material have a proven track record, while still subject to fading
strength will remain even after colour starts to fade. Shelf life again depends on location &
environment, regular cleaning & storage for best results for longevity.
Textilene Sling Maintenance
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean
rinse off with a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks. Ensure not
left wet for long periods of time to avoid mould build up.

6
PRODUCT CARE & MAINTENANCE
Glass Maintenance
Glass used is tempered for your safety; best results are to use placemats & coasters to avoid
scratching surface. Keep dust free, with floating glass please lift and clean underside of glass
with a soft clean cloth. Use of normal glass cleaning product is permissible but please rinse
surrounding areas with clean water to avoid damage to wicker or paint on aluminium frame.
Aluminium Frame Information
The majority of frames are mainly produced from aluminium, with the main benefit being a
light weight product for easier use. Some designs require steel to be used in certain sections for
added strength. While aluminium is rust resistant, bare metal can show signs of oxidation (red
film) this does not constitute rust. Simply you are able to wipe or sand surface to remove
oxidation mark.
Note you will need to touch up affected area with paint to stop from reoccurring. Steel itself
has a lower resistance to elements than aluminium and will show signs of rust as it ages.
Limited exposure & maintenance are best solutions for adding life to any furniture used in
outside areas.
Aluminium Frame Maintenance
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean
rinse off with a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks.
Note when cleaning if you find scratches in paint please cover with a paint to prevent
oxidation.