Furniture Solutions 18ZAR User manual

1
= Furniture Solutions
=
Imported by Furniture Solutions (Aust) Pty Ltd New South Wales,
Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
[e-mail]
INSTRUCTION MANUAL
ZARRAH RECLINER CHAIR & FOOTSTOOL
ITEM CODE: 18ZAR
18ZAR
H:98.5~78.5CM
D:78~117CM D:42.5CM
W:80CM
H:43CM
W:49CM

PRE-ASSEMBLY PREPARATION
2
Before you start :
1. Choose a clean, level, spacious assembly area . Avoid hard surfaces that
may damage the product
2. Take care when lifting.Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4.
5. Keep all hardware parts and packaging out of reach of small children .
6. Do not over tighten the screws and bolts as this may damage the threads
Always read the assembly instructions carefully before beginning assembly.
30
MINUTES
ALLOW TIME
X2
PEOPLE REQUIRED
18ZAR

3
PARTS LIST
A
B
C
D
E
F
G
1PC
4PCS
6PCS
1PC
1SET
M6X20 4mm/6mm
Knob/Shaft
1PC
3PCS
M6X20
M8X35
1.Seat Cushion
6.Footstool base
5.Chair Base
2.Backrest Cushion 3.Armrest Pads
4.Footstool Cushion
18ZAR
Footstool post
Chair post
1
2
4
5
6
3
3

4
To Assemble
Footstool:
Identify required
hardware before you start assembly. Note do not over tighten any bolts,
tighten
only until feels firm.
Take footstool cushion [?],
place upside down as per diagram. Next take footstool stem [B] and
aline all 4
holes as indicated in diagram. Then take bolt [A] by hand and insert thru hole in stem
into
threaded hole of footstool cushion and turn 2-3 times to ensure thread on bolt has gripped
threaded
hole in cushion. Do not tighten yet. Repeat for other 3 bolts [A] until all bolts are
seated correctly. Once all seated correctly take tool [H] and tighten all four (4) bolts until feels
firm. DO NOT OVER TIGHTEN. Then position footstool base [?] on a firm level surface and insert
stem into base as shown in diagram, you will need to ensure tube is inserted squarely, once you
are satisfied all square, with caution sit on footstool top to add the pressure required to lock in
stem and base together.
Move to Chair base Assembly next Page.
18ZAR
4
4
6

5
To Assemble
Chair, chair base assembly [?]
You will need
the help of another person thru this stage.
As
indicated on diagram place chair base [?] on a flat level surface. Take chair stem [C] insert
thicker
end into chair base, check that it is square. With help of another person pickup chair
seat
cushion and frame [?], locate hole in middle of frame under cushion, insert squarely onto
chair
and stem as indicated in diagram, check that it is fitted correctly should be no
movement in lower frame. Move to backrest assembly
Next is to fit backrest [?] to seat cushion. You will note that seat cushion can move forward and
backward, please position seat cushion so you have a clear view of threaded bolt hole in black
frame at back of cushion, you may need to move leather to view holes. With the help of
another person take backrest and aline backrest with seat cushion as shown in diagram. Note
on Right Hand Side Facing you will see a black painted pin extending from frame, please insert
coordinating hole on backrest, next aline threaded hole in seat cushion frame with hole in
backrest on left hand facing side of chair, insert by hand bolt [D] turn 2- times to ensure tread
is seated properly, please do not tighten as yet. Note this bolt acts as a pivot once fully tighten
do not over tighten once advice to tighten is instructed. Next as per diagram you will need to
fit 2 more bolts (pivots) higher up on backrest
18ZAR
1
5

6
To
Assemble Chair, Backrest assembly[?]
You will need
the help of another person thru this stage.
Next
is to fit backrest [?] to seat cushion. You will note that seat cushion can move forward
and backward,
please position seat cushion so you have a clear view of threaded bolt hole in
black frame
at back of cushion, you may need to move leather to view holes. With the help of
another person take
backrest and aline backrest with seat cushion as shown in diagram. Note
on Right Hand Side Facing you will see a black painted pin extending from frame, please insert
coordinating hole on backrest, next aline threaded hole in seat cushion frame with hole in
backrest on left hand facing side of chair, insert by hand bolt [D] turn 2- times to ensure tread
is seated properly, please do not tighten as yet.
Note this bolt acts as a pivot once fully tighten do not over tighten once advice to tighten is
instructed.
Next as per diagram you will need to fit 2 more bolts (pivots) higher up on backrest, aline
backrest cushion so that holes at top of chair frame match the threaded holes in backrest.
Take bolt [D] insert thru hole in chair frame into threaded hole and by hand turn 2-3 times to
seat thread correctly, once complete repeat for other side. Once both fitted take tool [G] and
tighten all 3 bolts that are in backrest. Note all these bolts act as pivot and only require to be
tightening until thread is not visible. Move to next page for arm pad assembly.
18ZAR
2
1

7
To fit
locking arm:
Please
locate underneath seat cushion on black frame a threaded hole as per the diagram.
Take
locking arm [F] insert threaded end into thread of chair frame and turn 2-3 times to seat
in thread
properly. Note this locking arm acts as a brake system for reclining action on chair,
please
see operating instruction in coming pages. Assembly Complete please see operating
instruction before you use.
To Assemble
armrest pads:
To fit armrest
pads [?] you will be required to pull backrest back to be as flat as possible.
Please
position armrest pad as per diagram, aline holes in chair frame to threaded holes in
armchair
pads, insert bolt [E] into hole of frame and into threaded hole of arm pads, turn 2-3
times
to seat thread correctly. Do not tighten yet. Repeat for other 2 bolts once all three (3)
bolts
are fitted, take tool [H] and tighten until feels firm. DO NOT OVER TIGHTEN.
Repeat process for other arm. Move to fit locking arm.
18ZAR
33
2
1

ASSEMBLY IS COMPLETE
818ZAR

918ZAR

10
CARE AND
MAINTENANCE
Varieties
of materials are used in construction of “Recliner” furniture range, Such as Stainless
Steel;
Chrome plated steel: Powder coated steel, Timber, Leather, PU synthetic fabric & a
variety
fabrics.
All
will require some form of maintenance to extend the life of finishes and general appearance.
Please
see below instruction unique to your chosen model.
Zarrah
Covering : Leather Full Hide with Corrected
Recliner Chair and footstool
Grain
Base : Laminated timber
Leather Covering;
Keep dust free at all times.
Regular use a damp soft clean cloth and wipe down leather.
Pay special attention to areas where skin touchers leather. IE : Armrest Pads, Headrest, front
section of chair and footrest tops.
Please clean up spills immediately. Ensure to dry properly before use.
Periodic Leather Cleaning;
Every 3-4 months you need to give leather a good clean to remove excess body oils.
Please purchase a propriety leather cleaner and follow all directions indicated on packaging.
You could also purchase a leather conditioner/protector to complement the leather after a
good clean.
Frequency of periodic cleaning can vary due to colour of leather, use and environment.
A chair used 2 hours a day will require less cleaning than a chair used 8 hours a day.
Areas of high humidity will require more cleaning than areas of low humidity.
Professional Cleaning;
Even the most diligent house keeper cannot always prevent leather from aging or looking tired.
We recommend you use the services of a reputable leather cleaning service when your cleaning
does not appear to make a difference in appearance.
Things to know about leather;
The surface of leather can be affected by chemicals used in hair spray, gel, mousse, perfume,
deodorants, some medications, alcohol and dye transference from clothing. Please factor this
into your cleaning regime.
Laminated Timber Base and Swivel Action;
Please remove dust and grit on exposed timber as required.
Every 3-4months lay chair over on it’s back please wipe and or vacuum action inside chair to
remove excess dust and fluff, pay special attention to swivel action at base of chair, ensure all
metal components are clean and free of impediments.
18ZAR